• Journal of the Korea institute for structural maintenance and inspection
• /
• 제21권6호
• /
• pp.67-73
• /
• 2017

Recently, the demand for large diameter piles has been rapidly increased in order to secure the allowable bearing capacity of pile foundation due to the increase of large structures such as high rise buildings. In this study, to improve the shear capacity of a conventional PHC pile, a large diameter composite PHC pile strengthened by in-filled concrete and shear reinforcement was manufactured. All the piles were tested according to the shear strength test method of Korean Standard. As a result of the shear test, the F-type piles which are produced without shear reinforcement occurred abrupt horizontal cracks after flexural and inclined shear cracks occurred. On the contrary, the FT-type piles which are produced with shear reinforcement exhibited stable flexural and inclined shear cracks uniformly over the entire pile without abrupt horizontal cracks. Furthermore, the maximum load of the large diameter composite PHC pile improved to 2.9 times in the F series, and more than 3.3 times in the FT series compared to the conventional PHC pile. This result indicated that FT-type piles had excellent composite behavior due to the shear reinforcement and effectively prevented the unstable growth of inclined shear cracks.

• Journal of the Korean Geotechnical Society
• /
• 제24권11호
• /
• pp.61-70
• /
• 2008

Load settlement behaviors and load transfer characteristics of rock-socketed pile subjected bi-directional load at pile tip were investigated using bi-directional pile load tests (BD PLT) performed on ten large-diameter drilled shafts at four sites. Based on test results, additional pile-toe displacement ($w_{bs}$) by coupled soil resistance was analyzed, and thus equivalent top loaded load-settlement curve of pile subjected bi-directional load was proposed by taking into account the coupled soil resistance. Through comparisons with field case studies, it is found that for test piles there exists effect of coupled soil resistance, which is represented by wbs, and thus an equivalent curve obtained by existing uncoupled methods can overestimate bearing capacity of piles by BD PLT. On the other hand, the analysis by the proposed method with soil coupling effect has a considerably larger settlement when compared with the results by uncoupled load transfer method and estimates reasonable load-settlement behaviors of test piles. In case of pile socketed in high strength rocks, however, effects of coupled soil resistance can be neglected.

• Journal of the Korean Geotechnical Society
• /
• 제29권7호
• /
• pp.17-36
• /
• 2013

In this paper, the empirical relations of skin friction and end bearing resistance with the results of site investigation in soft rock are proposed through the analysis of bi-directional pile load tests of rock socketed drilled shafts performed at large offshore bridge foundations and high-rise building projects (13 test piles in 4 projects). The site investigation and drilling for bi-directional pile load tests were performed at the centers of test piles, and f-w curves for skin friction and q-w curves for end bearing were plotted based on load-transfer measurements. From the above curves, the empirical relations of skin friction and end bearing resistance with the results of site investigation depending on the mobilized displacement are determined by multiple regression analysis and compared with previous studies. Since the f-w and q-w curves of rock-socketed piles in Korea show hardening behavior according to mobilized displacement, the developed empirical relations by the mobilized displacement are more reasonable than those of previous studies which could not consider the mobilized displacement and suggested the ultimate capacity with unconfined compressive strength only. Particularly, the developed equations correlated with unconfined compressive strength show the best correlations among the equations correlated with other parameters.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제25권3호
• /
• pp.77-84
• /
• 2021

In this study, flexural tests of prestressed high strength spun concrete (PHC) piles reinforced with infilled concrete and longitudinal rebars were conducted, where the longitudinal rebar ratio and the presence of sludge formed on the inner surface of PHC pile were set as key test variables. A total of six PHC pile specimens were manufactured, and their flexural behaviors including failure mode, crack pattern, longitudinal strain distribution in a section and end slip between external PHC pile and infilled concrete were measured and discussed in detail. The test results revealed that the flexural stiffness and strength increased as the longitudinal rebar ratio became larger, and that the sludge formed on the inner surface of PHC pile did not show any detrimental effect on the flexural performance. In addition to the experimental approach, this study presents a nonlinear flexural analysis model considering compatibility conditions and strain and stress distributions of the PHC piles and infilled concrete. The rationality of the nonlinear flexural analysis model was verified by comparing it with test results, and it appeared that the proposed model well evaluated the flexural behavior of PHC piles reinforced with infilled concrete and longitudinal rebars with a good accuracy.

• International Journal of Concrete Structures and Materials
• /
• 제4권1호
• /
• pp.9-15
• /
• 2010

Silica fume is a common addition to high performance concrete mix designs. The use of silica fume in concrete leads to increased water demand. For this reason, Florida Department of Transportation (FDOT) allows only a 72-hour continuous moist cure process for concrete containing silica fume. Accelerated curing has been shown to be effective in producing high-performance characteristics at early ages in silica-fume concrete. However, the heat greatly increases the moisture loss from exposed surfaces, which may cause shrinkage problems. An experimental study was undertaken to determine the feasibility of steam curing of FDOT concrete with silica fume in order to reduce precast turnaround time. Various steam curing durations were utilized with full-scale precast prestressed pile specimens. The concrete compressive strength and shrinkage were determined for various durations of steam curing. Results indicate that steam cured silica fume concrete met all FDOT requirements for the 12, 18 and 24 hours of curing periods. No shrinkage cracking was observed in any samples up to one year age. It was recommended that FDOT allow the 12 hour steam curing for concrete with silica fume.

• Journal of the Korean Geotechnical Society
• /
• 제39권2호
• /
• pp.19-30
• /
• 2023

Underground structures, such as compacted sand piles applied as soft ground countermeasures, are analyzed for settlement and stability by the composite ground design method. The basic principle of the composite ground design method is the arching effect. The reinforcing effect of the pile is evaluated as the stress-distribution ratio. When applying grouting piles with elastic properties using the ground reinforcement method, the existing stress-distribution ratio was only considered when the pile was installed. This study shows that the method of applying the stress-distribution ratio applied in previous studies should be changed when the ground reinforcement pile is installed at an arbitrary location in the ground without raising it to the ground surface. When high strength jet routing is applied, the stress-distribution ratio (n) to the in-situ ground generally ranges from 30 to 50. However, if the pile is located far from the surface and the depth goes down to the boundary depth of the stress sphere, the stress-distribution effect rapidly decreases, and the stress-distribution ratio converges to 1.5.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.91-98
• /
• 2006

The purpose of this study is to investigate the opacity and printing strength of MG paper overlaid plywood. The printing strength of ink on MG paper can be evaluated effectively by a formula $E^{*2}=[(L^{*})^{2}+(a^{*})^{2}+(b^{*})^{2}]^{1/2}$ that we proposed. Higher E value indicates good printing strength of ink-on-paper. We also assess the real color of translucent printed MG paper with a formula CIE ${\bigtriangleup}E^{*}$ (color difference between a pile of same paper to be opaque and fancy paper laminated board). In addition, the color difference on paper surface caused by the color of wood-based board (bottom) can be evaluated by a formula of Pc. No. Generally, an acceptable appearance quality of fancy boards is ${\bigtriangleup}E^{*}$ <2.0 and small Pc.No. value. The experimental results showed that Japan-made MG papers -J1, J2 and J3 have better printing strength and gloss than that of Taiwan-made paper (T1). The reason for this was that Taiwan-made paper has poor printing strength and low gloss, which might be correlated to the fiber compositions in paper. Higher printing strength can be seen for short fiber containing handsheets when comparing to that of handsheets. Nonetheless, low-freeness sheets gives better printing strength than that of high-freeness sheets. High-opacity MG paper gives good opacifying effect to the fancy paper laminated wood-based boards. Comparing the surface color of 2 kinds of fancy paper laminated boards, paperboard T1 laminated with high-opacity fancy paper showed slight color difference. The same results can be seen for $??g/m^{2}$ handsheets. Higher-opacity Acacia and Eucalyptus bleached sulfate pulps (short fiber) gives higher opacifying effect on the plywood when comparing to Northan pine and Radiata pine sulfate pulps(long fiber). The former ones also showed small color differences when comparing the color differences between the color of fancy paper and laminated paper board. Additionally, the color of bottom plywood can't be shown through for the high-opacify surface paper adhered to. Besides, the PC No of the base paper laminated board is small as well. Apparently, we can add colorants to the binders for the manufscture of various handsheets ($30g/m^{2}$) with various pulp mix ratios to increase the opacity of paperboards to certain extents. When we using yellow and brown binders in paper laminated board, the color difference between Acacia and Eucalyptus handsheets overlaid boards decreasing to 2.0 (acceptable ${\bigtriangleup}E^{*}$ <2.0, hard to discern), but not much improvement for Northern and Radiata pines. Definitely, show-through defects can be discernible for lower opacity papers. In general, admirable printing strength of fancy paper by which glued to plywood can be made with high-opacity paper and colored binders techniques.

• Journal of the Korean Geotechnical Society
• /
• 제19권5호
• /
• pp.253-261
• /
• 2003

Mechanical behavior of composition pound improved by sand compaction pile (SCP) with low replacement area ratio could be more significantly affected by mechanical interaction between sand piles and clays than that of clay ground improved by SD or SCP with high replacement area ratio. It is essential to elucidate the mechanical interaction in the improved clay ground, in order to accurately estimate behavior in reducing settlement of the improved ground and increasing strength of clays. In this paper, through a series of model tests of composition ground improved by SCP with low replacement area ratio, each mechanical behaviors of sand piles and clays in the composition ground during consolidation was elucidated, together with stress sharing behavior between sand piles and clays.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제16권2호
• /
• pp.58-64
• /
• 2012

Due to the influence of global oil prices, industrial productivity, which oil consumption is high, was significantly reduced. AC type of high-strength PHC piles is being manufactured through twice the steam curing process and this have resulted in a significant rise for product's manufacturing costs. NAC way other types of file manufacturing process has the advantage of reducing manufacturing costs by a turn of the steam curing. Nevertheless, because the initial strength be poor than that of AC method, shipment is being after the curing period of approximately three days. In addition, the growth of the product enhance with curing period can not be avoided, as a result, cost of inventory is acting as the rise. Piles by the AC method is immediately shipped after curing, damaging problems does not occur when they are introduced to the field site (for example, pile on-site). In the case of NAC, however, at least after the curing period of three days and after expressing the strength of 80 MPa or more, they are shipped on the scene. Therefore, NAC type has problems as follows: (1) increase in moderate inventory holding costs with type and (2) breakage in the field due to lack of strength. In this study, for NAC-typed PHC files, mixing characteristics research for the strength development at 1 day equivalent to AC method were conducted and strength characteristics with changes of original materials were evaluated were also identified.

• Journal of Advanced Research in Ocean Engineering
• /
• 제3권2호
• /
• pp.53-58
• /
• 2017

This study introduces the case of pipelines installed in subsea conditions and buried offshore. Such installations generate pore water pressure under the seabed because of cyclic wave excitation, which is an environmental load, and consistent cyclic wave loading that reduce the soil shear strength of the seabed, possibly leading to liquefaction. Therefore, in view of the liquefaction of the seabed, stability of the subsea pipelines should be examined via calculations using a simple method for buried subsea pipelines and floating structures. Particularly, for studying the possible liquefaction of the seabed in regard to subsea pipelines, high waves of a 10- and 100-year period and the number of occurrences that are affected by the environment within a division cycle of 90 s should be applied. However, when applying significant wave heights (HS), the number of occurrences within a division cycle of 3 h are required to be considered. Furthermore, to research whether dynamic vertical load affect the seabed, mostly a linear wave is used; this is particularly necessary to apply for considering the liquefaction of the seabed in the case of pile structure or subsea pipeline installation.