• 전자공학회논문지SC
• /
• 제44권1호
• /
• pp.85-93
• /
• 2007

본 논문에서는 다수의 병렬 입.출력 환경을 위한 높은 노이즈 마진을 갖고 있는 LVDS I/O 회로를 소개한다. 제안된 LVDS I/O회로는 송신단과 수신단으로 구성되어 있으며 송신단 회로는 차동위상 분할기와 공통모드 피드백(common mode feedback)을 가지고 있는 출력단으로 이루어져 있다. 차동위상 분할기는 SSO(simultaneous switching output) 노이즈에 의해 공급전압이 변하더라도 안정된 듀티 싸이클(duty cycle)과 $180^{\circ}$의 위상차를 가진 두 개의 신호를 생성한다. 공통모드 피로백을 가지고 있는 출력단 회로는 공급전압의 변화에 상관없이 일정한 출력전류를 생성하고 공통모드 전압(common mode voltage)을 ${\pm}$0.1V 이내로 유지한다. LVDS 수신단 회로는 VCDA(very wide common mode input range differential amplifier)구조를 사용하여 넓은 공통 입력전압 범위를 확보하고 SSO 노이즈에 의한 공급 전압의 변화에도 안정된 듀티 싸이클(50% ${\pm}$ 3%)을 유지하여 정확한 데이터 복원이 가능하다. 본 논문에서 제안한 LVDS I/O 회로는 0.18um TSMC 라이브러리를 기본으로 하여 설계 되었으며 H-SPICE를 이용하여 시뮬레이션 하였다.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.153-160
• /
• 2020

In this paper, we present a hydrostatic bearing design and rotordynamic analysis of a pump-and-drive turbine module for a 250-kW supercritical CO₂ cycle application. The pump-and-drive turbine module consists of the pump and turbine wheel, assembled to a shaft supported by two hydrostatic radial and thrust bearings. The rated speed is 21,000 rpm and the rated power is 143 kW. For the bearing operation, we use high-pressure CO₂ as the lubricant, which is supplied to the bearing through the orifice restrictor. We calculate the bearing stiffness and flow rate for various orifice diameters, and then select the diameter that provides the maximum bearing stiffness. We also conduct a rotordynamic analysis based on the design parameters of the pump-and-drive turbine module. The predicted Campbell diagram shows that there is no critical speed below the rated speed, owing to the high stiffness of the bearings. Furthermore, the predicted damping ratio indicates that there is no unstable mode. We conduct the operating tests for the pump and drive turbine modules within the supercritical CO₂ cycle test loop. The pressurized CO₂, at a temperature of 136℃, is supplied to the turbine and we monitor the shaft vibration during the test. The test results show that there is no critical speed below the rated speed, and the shaft vibration is controlled to below 3 ㎛.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.381-383
• /
• 2007

Charge-pump high voltage inverter for Plasma backlight with CIM(Current Injection Method) is proposed in this paper. Adoption of ERC is a new attempt in high voltage inverter so that it is not only energy recovery but also improvement of discharge stability and system unstability which is interrupted by noise. Using a charge-pump technique enables low voltage switches to be usable, the cost can be reduce. CIM is adopted to achieve high speed energy recovery in proposed circuit. Operations of the proposed circuit are analyzed for each mode. The proposed circuit is verified to be applicable on a 32 inch plasma backlight panel by experimental results.

• 센서학회지
• /
• 제33권1호
• /
• pp.12-17
• /
• 2024

Floating inverter amplifiers (FIAs) have recently garnered considerable attention owing to their high energy efficiency and inherent resilience to input common-mode voltages and process-voltage-temperature variations. Since the voltage gain of a simple FIA is low, it is typically cascaded or cascoded to achieve a higher voltage gain. However, cascading poses stability concerns in closed-loop applications, while cascoding limits the output swing. This study introduces a gain-enhanced FIA that features cross-coupled body biasing. Through simulations, it is demonstrated that the proposed FIA designed using a 28-nm complementary metal-oxide-semiconductor technology with a 1-V power supply can achieve a high voltage gain (> 90 dB) suitable for dynamic open-loop applications. The proposed FIA can also be used as a closed-loop amplifier by adjusting the amount of positive feedback due to the cross-coupled body biasing. The capability of achieving a high gain with minimum-length devices makes the proposed FIA a promising candidate for low-power, high-speed sensor interface systems.

• Journal of Astronomy and Space Sciences
• /
• 제27권2호
• /
• pp.107-116
• /
• 2010

We developed the playback control software for a high-speed playback system which is a component of the Korea-Japan Joint VLBI Correlator (KJJVC). The Mark5B system, which is a recorder and playback system used in the Korean VLBI Network (KVN), has two kinds of operation mode. That is to say, the station unit (SU) mode, which is for the present Mark4 system, and the VSI mode, which is for the new VLBI standard interface (VSI) system. The software for SU is already developed and widely used in the Mark4 type VLBI system, but the software for VSI has only been developed for recording. The new VLBI system is designed with a VSI interface for compatibility between different systems. Therefore, the playback control software development of the VSI mode is needed for KVN. In this work, we developed the playback control software of the Mark5B VSI mode. The developed playback control software consists of an application part for data playing back, a data input/output part for the VSI board, a module for the StreamStor RAID board, and a user interface part, including an observation time control part. To verify the performance of developed playback control software, the playback and correlation experiments were performed using the real observation data in Mark5B system and KJJVC. To check the observation time control, the data playback experiment was performed between the Mark5B and Raw VLBI Data Buffer (RVDB) systems. Through the experimental results, we confirmed the performance of developed playback control software in the Mark5B VSI mode.

• 한국정보통신학회논문지
• /
• 제21권4호
• /
• pp.767-773
• /
• 2017

본 논문에서는 HEVC 부호기를 위한 효율적인 Intra Prediction Angular 모드 결정 하드웨어 설계를 제안한다. HEVC의 Intra Prediction은 현재 블록 주변의 재구성된 샘플들을 참조하여 현재 블록을 예측하는 방법이다. Intra Prediction에서는 1개의 DC 모드, 1개의 Planar 모드, 33개의 Angular 모드로 총 35개의 모드를 지원한다. HEVC의 Intra Prediction은 35개의 모드 중에서 최적의 모드를 결정한 후 예측하여 부호화 성능을 향상 시킨다. 그러나 35가지의 모드를 모두 처리하기 위해서는 많은 연산 복잡도와 처리시간이 요구된다. 그러므로 본 논문에서는 원본 영상 픽셀의 차이 값을 비교하여 Angular 모드를 효율적으로 결정하는 알고리즘을 적용한 하드웨어 설계를 제안하였다. 또한 효율적인 알고리즘의 사용을 통해 하드웨어 면적을 감소시켰다. 제안된 하드웨어 구조는 Verilog HDL로 설계하였으며, 65nm 공정으로 합성하였다. 합성 결과 14.9K개의 게이트로 구현되었고, 최대 동작 주파수는 2GHz이다.

• 한국안전학회지
• /
• 제28권1호
• /
• pp.12-17
• /
• 2013

Considering the wind power system and the rotor blades which are composed of much technology, the wind power blade would be the most dangerous part because it revolves at high speed and weighs about dozens of tons, if the accident happens. Therefore, the light weight composite materials have been replacing as substitutional materials. The object of this study is to examine the delamination and damage for CFRP/GFRP hybrid composite that is used for strength improvement of a wind power blade. The influence of the initial crack length and fiber orientation for the interlaminar delamination was exposed for the blade safety. Plain woven CFRP instead of GFRP was inserted into the layer of the box spar for improving the strength and blade life. DCB(Double Cantilever Beam) specimen was used for evaluating fracture toughness and damage evaluation of interlaminar delamination. The material used in the experiment is a commercial material known as CF 3327 EPC in plain woven carbon prepreg(Hankuk Carbon Co.) and UD glass fiber prepreg(Hyundai Fiber Co.). From the results, crack growth rate is not so different according to the variation of the initial crack length. Mode I interlamainar fracture toughness of fiber direction $0^{\circ}$ is higher than that of $45^{\circ}$. Interlaminar fracture has an effect on fiber direction and K decreased with lower value according to increasing initial crack length. Also energy release rate fracture toughness was evaluated because CFRP/GFRP hybrid composite with a different thickness is under the mixed mode loading condition. The interlaminar fracture was almost governed by mode I fracture even though the mixed mode.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.3-5
• /
• 2008

This paper presents a hybrid winding connection method for torque characteristics improving of a traction SRM. In order to get a high torque in wide speed range and torque ripple reduction, series and parallel winding connection are changed according to operating speed. From the analysis of torque character operation mode and efficiency, the proposed control scheme is verified.

• 전자공학회논문지B
• /
• 제33B권3호
• /
• pp.38-46
• /
• 1996

In this paper, a multi-velocity log system which uses ultrasonic pulsed doppler signal is developed. The output of the system is the absoluted velcocity of the ship. By using digitral signal processing, we get the vector velocity which displays the ship's speed about fore, aft, port and starboard. And this system give us the information about depth. This multi-velocity system has a large merit that is bottom and water track velocity. In addition, this has the high accuracy and can measure the water-depth according to the deep mode. And the fish finder, echo sounder or docking system will be made by applying the speed log system.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.273-276
• /
• 2005

Performance analysis of a solid oxide fuel cell/micro gas turbine hybrid system is conducted at design-point and part-load conditions and its results are discussed in this study. With detailed considerations of the heat and mass transfer phenomena along various flow streams of the SOFC, the analysis based on a quasi-2D model reasonably predicts its performance at the design-point operating conditions. In case of part-load operations, performance of the hybrid system to three different operation modes(fuel only control, speed control, and VIGV control) is compared. It is found that the simultaneous control of both supplied fuel and air to the system with a variable MGT rotational speed mode is the optimum choice for the high performance operation. And then, the dynamic characteristics of a solid oxide fuel cell are briefly introduced.