• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.1
• /
• pp.82-88
• /
• 2001

The demands of high data transfer rate and high recording density in optical disk memory device are being increased. In this paper, 4 design parameters for next generation optical disk are investigated. As for the high data transfer rate, two design parameters such as driving acceleration and transmissibility are introduced. As the high recording density is concerned, the minimum linearity and the tilt of the actuator are introduced. Two kinds of pickup actuator are used to evaluate the validity of the parameters through the simulation and the experiment. The 4-wire actuator has good linearity but bad stability and tilt characteristics, while the rotary and axis actuator has good stability for the external vibration but bad linearity. It is demonstrated that the newly proposed design parameters are available to design and evaluate quantitatively the performance of the actuator for the next generation optical disk.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.235-237
• /
• 1998

Gradient coil offers the spatial informations of sample or patient in Nuclear Magnetic Resonance Imaging(NMRI) and its gradient field linearity over the field of view(FOV) has many influence on the MR imaging. Accurate and good quality MR imaging can be acquired by the high gradient field linearity over the FOV. So it is an important part to design of gradient coil with good linearity in the wide imaging range. Usually, Z-directional gradient field is generated by using the Helmholtz type coil which is consisted of one-pair loop with anti-current path. It gets less about 40% linearity of the diameter spherical volume(DSV). In this study, we calculated optimized geometrical parameters of two-pair loop system to cancel odd terms up to $B_7$ included effectively. we also analyzed and compared the gradient field distribution and linearity of the common Helmholtz coil with them of the two-pair loop system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.713-721
• /
• 2004

This paper presents a high Performance LNA based on InGaP/GaAs HBT for 5.4㎓ WAM band applications. During the past days, InGaP/GaAs HBT has been being used for mainly high power amplifiers, but InCaP/GaAs is recognized as a suitable device for RF single chip. At this point, the research about a high performance LNA based on InGaP/GaAs HBT must be preceded, and in this paper, a excellent linearity and noise characteristics LNA based on InGaP/GaAs HBT is desisted and fabricated. The LNA is integrated in new of 0.9${\times}$0.9$\textrm{mm}^2$ single chip with high Q spiral inductors and MIM capacitors. The proposed LNA is biased at current point for optimum noise figure and gain characteristics, futhermore, excellent linearity is achieved. The proposed LNA shows 13㏈ gain, 2.1㏈ noise figure, and excellent linearity in terms of IIP3 of 5.5㏈m.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.888-891
• /
• 2003

This paper describes on the fabrication and characteristics of micro ceramic thin-film type pressure sensors based on Ta-N strain-gauges for high-temperature applications. The Ta-N thin-film strain-gauges are deposited onto thermally oxidized Si diaphragms by RF sputtering in an argon-nitrogen atmosphere($N_2$ gas ratio: 8 %, annealing condition: $900^{\circ}C$, 1 hr.), Patterned on a wheatstone bridge configuration, and use as pressure sensing elements with a high stability and a high gauge factor. The sensitivity is $1.097{\sim}1.21mV/V.kgf/cm^2$ in the temperature range of $25{\sim}200^{\circ}C$ and the maximum non-linearity is 0.43 %FS. The fabricated pressure sensor presents a lower TCR, non-linearity than existing Si piezoresistive pressure sensors. The fabricated micro ceramic thin-film type pressure sensor is expected to be usefully applied as pressure and load sensors that is operable under high-temperature environments.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.395-398
• /
• 2004

High-linearity voltage-controlled current sources (VCCSs) circuits for wide voltage-controlled oscillator and automatic gun control were proposed. The VCCS consists of emitter follower for voltage input, two common-base amplifier which their emitter connected for current output, and current mirror which connected the two amplifier for large output current. The VCCS used only five transistors and a resistor without an extra bias circuit. Simulation results show that the VCCS has current output range from 0mA to 300mA over the control voltage range from 1V to 4.8V at supply voltage 5V. The linearity error of output current has less than $1.4\%$ over the current range from 0A to 300mA.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.181-184
• /
• 2002

This paper describes fabrication and characteristics of ceramic pressure sensor for working at high temperature. The proposed pressure sensor consists of a Ta-N thin-film, patterned on a Wheatstone bridge configuration, sputter deposited onto thermally oxidized Si membranes with an aluminium interconnection layer. The fabricated pressure sensor presents a low temperature coefficient of resistance, high sensitivity, low non-linearity and excellent temperature stability The sensitivity is 1.097∼1.21 mV/V$.$kgf/$\textrm{cm}^2$ in the temperature range of 25∼200$^{\circ}C$ and the maximum non-linearity is 0.43 %FS.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.103-106
• /
• 2005

The material properties of membrane for stratospheric airship is experimentally investigated. Mechanical tensile properties of the membrane material at room, high and low temperature are measured using instron with thermal chamber. Experimentaly, material non-linearity is observed at room and high temperature. In order to simulate material non-linearity caused by the uniaxial extension curve of a woven fabric, the nonlinear hyperelastic problem is considered with finite clement program of ABAQS. Numerical results are compared with experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.618-627
• /
• 2005

In this paper, we have compared and analyzed the performance of high amplifier using Doherty technique to improve linearity and efficiency of base station and repeater Power amplifier for WCDMA. This Doherty amplifier implements with 3dB branch line coupler and $90^{\circ}C$ transmission line The phase offset line is designed to maintain the high linearity and efficiency at the low efficiency Period of the power amplifier CW 1-tone experimental results at the WCDMA frequency $2.11{\sim}2.17GHz$ shows that Doherty amplifier which achieves power add efficiency(PAE) of 50% at 6dB back off the point from maximum output power 52.3 dBm, obtains higher efficiency of 13.3% than class AB Finding optimum bias Point after adjusted gate voltage, Doherty amplifier shows that $IMD_3$ improves 4dB.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.205-207
• /
• 2006

In this paper, we present a design procedure of high linearity LNA using CMOS technology. To enhance the low linearity of the inherent CMOS transistor, we adopt the modified derivate superposition with adding external capacitor. The simulation of the designed LNA shows $IIP_3$ of +12-dBm, power gain of 13.8-dB, noise figure of 1.75-dB over the 900 MHz UHF RFID frequencies. The circuit draws the current of 4.2 mA from 1.8-V supply voltage.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.405-409
• /
• 2001

This paper describes fabrication and characteristics of metal thin-film pressure sensor for working at high temperature. The proposed pressure consists of a chrom thin-film, patterned on a Wheat stone bridge configuration, sputter-deposited onto thermally oxidized Si membranes with an aluminium interconnection layer. The fabricated pressure sensor presents a low temperature coefficient of resistance, high-sensitivity, low non-linearity and excellent temperature stability. The sensitivity is 1.097∼1.21mV/V$.$kgf/$\textrm{cm}^2$ in the temperature range of 25∼200$^{\circ}C$ and the maximum non-linearity is 0.43%FS.