• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.770-775
• /
• 2004

Although $High-T_c $superconducting HTS antennas have high efficiency and high gain, narrow bandwidth due to the high Q is the major limitation for application of satellite communication and mobile communication. Defining bandwidth as the frequency range over which standing wave ratio (SWR) is 2:1 or less, HTS antenna bandwidths are typically less than 1 %. Thus considerable effort has been focused on developing HTS antennas for broadband operation. In this work the HTS antenna array, using the bipin antenna which consisted of two triangle-radiation patches, was designed and fabricated using a ${YBa}_2{Cu}_3{O}_7x (YBCO)$ superconducting thin film on a MgO substrate for broadband operation. Also gold antennas with the same dimension as our HTS antennas were fabricated on the MgO substrate for the comparison. Experimental results for both antennas were reported in terms of radiation patterns, return losses, bandwidths and other various characteristics. The center frequency of HTS antennas was 20.28 GHz and the bandwidth obtained was significant 10 %.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.11
• /
• pp.501-507
• /
• 2003

In this study, microscale, high-performance, solenoid-type RF chip inductors were investigated. The size of the RF chip inductors fabricated in this work was 1.0${\times}$0.5${\times}$0.5㎣. 96% $Al_2$ $O_3$and I-type were used as the material and shape of the core, respectively. The copper (Cu) wire with 6 turns was employed as the coils. The diameter (40${\mu}{\textrm}{m}$) and position (middle) of the coil and the length (0.35mm) of solenoid were determined by a high-frequency structure simulator (HFSS) to maximize the performance of the inductors. High frequency characteristics of the inductance (L) and quality-factor (Q) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The inductors developed have inductances of 10.8nH and quality factors of 25.2 to 50 over the frequency ranges of 250MHz to l GHz, and show results comparable to those measured for the inductors prepared by CoilCraf $t^{Tm}$ . The simulated data predicted the high-frequency data of the L and Q of the inductors developed well.l.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.688-692
• /
• 2003

For high voltage operation, a new type of piezoelectric transformer using radial vibration of disk, poled with the same direction was proposed. The piezoelectric ceramics was composed to PZT-PMN-PSN. The diameter and thickness of a disk type piezoelectric transformer were 45［mm］and 4［mm］, respectively The surface ratio of driving electrode and generating electrode of the piezoelectric transformer was 2 : 1. The resonance characteristics of input admittance, step-up voltage ratio and power transmission efficiency of the piezoelectric transformer were measured by varying the load resistance(0.1∼70［kΩ］). As a result, both resonance frequency and step-up voltage ratio increased with increasing load resistance. The step-up voltage ratio was reached more than 60 times under no load resistance. The maximum efficiency of 97% at load resistance of 2kΩ was obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.202-202
• /
• 2010

This study focused on the characteristics of single crystal solar cell using the impedance technique. In this experiment, the impedance was measured according to frequency's from 1mHz until 2MHz. The solar cell is R-L-C series circuit. Capacitance reactance was changed according to changing from low frequency to high frequency. It could know that the impedance was changed according to the frequency increases in solar cell.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.89-94
• /
• 1999

In this study, a new technology to bond the PZT with connection board, which is a core technology for the fabrication of medical micro high frequency sensors, was developed. Two technologies were adopted. One is bonding of In using thermal heating, he other is bonding of Pb using a high frequency heating machine. In case of thermal eating, bonding was failed because of the contaminations of In surface. But, when using high frequency healing machine, we developed good bonding characteristics at various experimental conditions and thickness of the electrode material.

• KIEAE Journal
• /
• v.1 no.2
• /
• pp.47-54
• /
• 2001

Single sound absorbers such as porous materials, panels, and Helmholts resonators have limited performance with some extents of frequency region. For example, porous materials do not attenuate low frequency sounds, while panels do not absorb high frequency sounds. Composite absorption structure with coverings, porous materials, and air gaps are an alternative for wide band sound absorption. Slits, panels, perforated panels are those materials for coverings, glass wool, mineral wool, polyester, and polyurethane are frequently used porous materials. Air gap between the porous material and background surface is one of major factors which governs the absorption characteristics of composite absorption structures, especially in the low frequency area. Calculations and measurements show that the absorption coefficients of composite absorption structure, in mid and low frequency bands, are getting higher with increased air gaps. Perforated panels rather than slits and panels are good coverings with higher number as far as absorption coefficient is concerned. Perforated panels with porous materials and 37 cm of air gaps in background have high absorption coefficients for all frequency bands, above 0.7 to 1.0. All measurements are performed in reverberation chamber, Mokpo National University, according to ISO 354 and ISO 3382.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.502-507
• /
• 2004

The forward planar transformer, which had power capacity of 300 W, input voltage of 220 V, output voltage of 15 V, and switching frequency of 300 KHz, was designed and manufactured by using the planar core with large effective area and the flat copper leadframes for miniaturization and high efficiency of the switching mode power supply (SMPS). As well as, a forward converter equipped with the above mentioned planar transformer was manufactured and electromagnetic characteristics were investigated. The numerical value of turns for 1st and 2nd winding were 15 and 2 respectively The self inductance of 1st winding was 1.592 mH, very low leakage inductance of 2.7 $\mu$H, and the coupling factor of 0.928 were obtained at switching frequency of 300 KHz. The high efficiency of 88.62 % for the SMPS equipped with planar transformer was obtained at power capacity of 300 W.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.8
• /
• pp.780-784
• /
• 2006

We present high aspect ratio air-core solenoid inductors with $100{\mu}m\;and\;200{\mu}m$ tall via structures on Pyrex wafer. The effect of various parameters such as different number of turns, via heights, pitch distance between turns on inductor's radio frequency (RF) characteristics have been studied. The highest Q factor we obtained from various solenoid inductors is 72.8 at 9.7 GHz, which was produced by a 3-turn inductor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.2 no.2
• /
• pp.73-79
• /
• 2001

In this paper, the transmitted noise reduction performance of piezoelectric smart panels is experimentally studied. The proposed piezoelectric smart panels are comprised of plate structure on which piezoelectric sensor/actuators are bonded and sound absorbing material is provided. It is a combination of passive and active approaches utilizing a passive effect at high frequencies and an active effect at low frequencies. To prove the concept of piezoelectric smart panels, an acoustic measurement experiment is performed. An acoustic tunnel is designed and its acoustic characteristics are tested. Below 800Hz, the tunnel exhibits a plane wave guide characteristics. When an absorbing material is bonded on a single plate, a remarkable transmitted noise reduction in mid frequency range is observed except the first resonance frequency. By enabling the active control of single smart panel with negative feedback control. about 10dB noise reduction is achieved at the resonance frequencies. The double smart panel got 4dB at the first resonance frequency and has more potential to reduce the transmitted noise in a wide range frequency. Piezoelectric smart panels incorporating passive absorbing material and active piezoelectric devices is a promising technology for noise reduction in a wide range frequency.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.21-28
• /
• 2004

In modem manufacturing industries such as the airplane and automobile, aluminum alloys which are remarkable in durability have been utilized effectively. High-speed machining technology for surface roughness quality of workpiece has been applied in these fields. Higher cutting speed and feedrates lead to a reduction of machining time and increase of surface quality. Furthermore, the reduction of time required for polishing or lapping of machined surfaces improves the production rate. Traditional milling process for high speed cutting can be machined with end mill tool. However, such processes are generally cost-expensive and have low material removal rate. Thus, in this paper, face milling cutter which gives high MRR has developed face milling cutter body for the high speed machining of light alloy to overcome the problems. Also vibration experiment to detect natural frequency in free state and frequency characteristics during machining are performed to escape resonance.