• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.12
• /
• pp.8-13
• /
• 2001

Cerium oxide ($CeO_2$) thin film has been proposed as a buffer layer between the ferroelectric thin film and the Si substrate in Metal-Ferroelectric-Insulator-Silicon (MFIS) structures for ferroelectric random access memory (FRAM) applications. In this study, $CeO_2$ thin films were etched with $Cl_2$/Ar gas mixture in an inductively coupled plasma (ICP). Etch properties were measured for different gas mixing ratio of $Cl_2$($Cl_2$+Ar) while the other process conditions were fixed at RF power (600 W), dc bias voltage (-200 V), and chamber pressure (15 mTorr). The highest etch rate of $CeO_2$ thin film was 230 ${\AA}$/min and the selectivity of $CeO_2$ to $YMnO_3$ was 1.83 at $Cl_2$($Cl_2$+Ar gas mixing ratio of 0.2. The surface reaction of the etched $CeO_2$ thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. There is a Ce-Cl bonding by chemical reaction between Ce and Cl. The results of secondary ion mass spectrometer (SIMS) analysis were compared with the results of XPS analysis and the Ce-Cl bonding was monitored at 176.15 (a.m.u). These results confirm that Ce atoms of $CeO_2$ thin films react with chlorine and a compound such as CeCl remains on the surface of etched $CeO_2$ thin films. These products can be removed by Ar ion bombardment.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.2
• /
• pp.66-72
• /
• 2020

The difference of plasma resistance between the CAS glass bulk and coating films were compared. Plasma resistance was confirmed by analyzing the etch rate and the microstructure of the surface when the CAS glass bulk and the glass coating film were etched with CF₄/O₂/Ar plasma gas. CAS glass coating film was etched up to 25 times faster than the glass bulk. A statistically high correlation between the surface roughness and the etching rate of the coating film was derived, and thus, the high surface roughness of the coating film was determined to cause rapid etching. In addition, cristobalite crystals that has a low Ca content and a high Si content, was foamed on the glass coating film. Therefore, the CAS glass coating film is considered to have low plasma resistance compared to the glass bulk.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.4
• /
• pp.318-331
• /
• 1995

The c - axis oriented single crystal of $LiNbO_3$ and $LiNbO_3$ : 5mol%MgO was success-fully grown by Floating zone method using halogen lamp as a heat source. The effects of the sintering condition of the feed rod and the atmosphere gas during the crystal growth on the be havior of the feed rod/melt interface were studied for growing crystal with the high quality, and then, the optimum growth conditions were determined by studying the experimental param eters, such as gas flow rate, pulling rate, rotation speeds of the feed rod and the seed. The grown crystals were analyzed using the chemical etching to observe the tch pattern and the ICP (Inductively Coupled Plasma) to determine the composition uniformity and the impurity content of Fe. The effects of additive (5 mol % MgO) on the transmittance and refractive index was, also, analyzed. In order to compare the nonlinear optical oharacteristics of $LiNbO_3$ with those of the other optical materials, the nonlinear optical refractive index ($n_2$) was calcu l lated using the measured refractive index.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.459-465
• /
• 1993

By making the inter-metal PECVD $SiO_2$ as a Si rich oxide under the SOG, the hydrogen and water related diffusants could be captured a t SI dangling bonds. This gettering process was known to prevent the device characteristics degradations related to the H, $H_20$. The basic characteristics of Si rich oxide have been studied according to changing high/low frequency power and $SiH_4/N_2O$ gas flow ratio in PECVD. As increase in low frequency power, deposition rate decreased but K.I. and compressive stress increased. Decrease of the water peaks of FTIR spectra at the wave number range of 3300~3800$\textrm{cm}^{-1}$' also indicated that intensty the films were densified. As increase in SiH, gas flow rate, deposition rate, R.I. and etch rate increased while compressive stress decreased. F'TIK spectra showed that peak intensity corresponding to Si-0-Si stretching vibration decreased and shifted to the lower wave numbers. But AES showed that Si dangl~ng bonds were increased as a result of lower Si:O(l: 1.23) ratlo inthe Si rich oxide as compared to Si : O(1 : 1.98) ratio of usual oxide.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.62-62
• /
• 2003

고밀도 유도결합 플라즈마(high density inductively coupled plasma) 식각은 GaAs 이종접합 양극성 트랜지스터(HBTs)와 고속전자 이동도 트랜지스터(HEMTs)와 같은 GaAs 기반 반도체의 정교한 패턴을 형성하는데 더욱 많이 이용되고 있다 본 연구는 고밀도 플라즈마 소스(source)인 평판형(planar) 고밀도 유도결합 플라즈마 식각장치를 이용하여 $BCl_3$ 와 $BCl_3/Ar$ 가스에 따른 GaAs 식각결과를 비교 분석하였다. 공정변수는 ICP 소스 파워를 0-500W, RIE 척(chuck) 파워를 0-150W, 공정압력을 0-15 mTorr 이었다. 그리고 가스 유량은 20sccm(standard cubic centimeter per minute)으로 고정시킨 상태에서 Ar 첨가 비율에 따른 GaAs의 식각결과를 관찰하였다. 공정 결과는 식각률(etch rate), GaAs 대 PR의 선택도(selectivity), 표면 거칠기(roughness)와 식각후 표면에 남아 있는 잔류 가스등을 분석하였다. 20 $BCl_3$ 플라즈마를 이용한 GaAs 식각률 보다 Ar이 첨가된 (20-x) $BC1_3/x Ar$ 플라즈마의 식각률이 더 우수하다는 것을 알 수 있었다. 식각률 증가는 Ar 가스의 첨가로 인한 GaAs 반도체와 Ar 플라즈마의 충돌로 나타난 결과로 예측된다. $BCl_3$ 와 $BC1_3/Ar$ 플라즈마에 노출된 GaAs 반도체 모두 표면이 평탄하였고 수직 측벽도 또한 우수하였다. 그리고 표면에 잔류하는 성분은 Ga와 As 이외에 $Cl_2$ 계열의 불순물이 거의 발견되지 않아 매우 깨끗함을 확인하였다. 이번 발표에서는 $BCl_3$ 와 $BCl_3/Ar$ 플라즈마를 이용한 GaAs의 건식식각 비교에 대해 상세하게 보고 할 것이다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.297-303
• /
• 2003

Mn-Ni-Co type thin films were prepared at various conditions by a rf magnetron sputtering system. At the condition. or substrate temperature of $300^{\circ}C$ and $Ar/O_2$= 10/0, a cubic spinel phase was obtained. When oxygen was included in process gas, a cubic spinel phase was not formed even after the thermal annealing at $900^{\circ}C$. The thermistor thin film had no other elements except Mn, Ni and Co. The infrared reflection spectra of the thermistor thin films showed that the films had somewhat high reflectance for incoming infrared ray with some angle. The etch rate of the thermistor thin films was about 63nm/min at a condition of DI water : $HNO_3$: HCl = 60 : 30 : 10 vol%. The B constant and temperature coefficient of resistance of the thermistor thin films were 3500 K and -3.95 %/K, respectively. The voltage responsivity of the thermistor thin film infrared sensor was 108.5 V/W and its noise equivalent power and specific detectivity were $5.1\times 10^{-7}$ W/$Hz^{-1/2}$ and $0.2\times 10^6$cm $Hz^{1/2}$/W, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.113-114
• /
• 2009

Silicon carbide is one of the most attractive and promising wide band-gap semiconductor material with excellent physical properties and huge potential for electronic applications. Up to now, the most successful method for growth of large SiC crystals with high quality is the physical vapor transport (PVT) method [1, 2]. Since further reduction of defect densities in larger crystal are needed for the true implementation of SiC devices, many researchers are focusing to improve the quality of SiC single crystal through the process modifications for SiC bulk growth or new material implementations [3, 4]. It is well known that for getting high quality SiC crystal, source materials with high purity must be used in PVT method. Among various source materials in PVT method, a SiC powder is considered to take an important role because it would influence on crystal quality of SiC crystal as well as optimum temperature of single crystal growth, the growth rate and doping characteristics. In reality, the effect of powder on SiC crystal could definitely exhibit the complicated correlation. Therefore, the present research was focused to investigate the quality difference of SiC crystal grown by conventional PVT method with using various SiC powders. As shown in Fig. 1, we used three SiC powders with different particles size. The 6H-SiC crystals were grown by conventional PVT process and the SiC seeds and the high purity SiC source materials are placed on opposite side in a sealed graphite crucible which is surrounded by graphite insulation[5, 6]. The bulk SiC crystal was grown at $2300^{\circ}C$ of the growth temperature and 50mbar of an argon pressure. The axial thermal gradient across the SiC crystal during the growth is estimated in the range of $15\sim20^{\circ}C/cm$. The chemical etch in molten KOH maintained at $450^{\circ}C$ for 10 min was used for defect observation with a polarizing microscope in Nomarski mode. Electrical properties of bulk SiC materials were measured by Hall effect using van der Pauw geometry and a UV/VIS spectrophotometer. Fig. 2 shows optical photographs of SiC crystal ingot grown by PVT method and Table 1 shows electrical properties of SiC crystals. The electrical properties as well as crystal quality of SiC crystals were systematically investigated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.2
• /
• pp.89-93
• /
• 2017

GaN single crystals were grown by controlling of various processing parameters such as growing temperature, V/III ratio and growing rate. We optimized thickness of bulk GaN single crystal by analyzing defect of surface and inside of the GaN single crystal for application to high brightness and power device. 2-inch bulk GaN single crystals were grown by HVPE (hydride vapor phase epitaxy) on sapphire and their thickness was 0.3~7.0 mm. Crystal structure of the grown bulk GaN was analyzed by XRD (X-ray diffraction). The surface characteristics of the grown bulk GaN were observed by OM (optical microscope) and SEM (scanning electron microscopy) with measuring EPD (etch pits density) of the GaN crystals.

• Restorative Dentistry and Endodontics
• /
• v.33 no.2
• /
• pp.141-147
• /
• 2008

This study was aimed to develop an instrument for real-time measurement of fluid conductance and to investigate the hydrodynamics of dentinal fluid. The instrument consisted of three parts; (1) a glass capillary and a photo sensor for detection of fluid movement, (2) a servo-motor, a lead screw and a ball nut for tracking of fluid movement, (3) a rotary encoder and software for data processing. To observe the blocking effect of dentinal fluid movement, oxalate gel and self-etch adhesive agent were used. BisBlock (Bisco) and Clearfil SE Bond (Kuraray) were applied to the occlusal dentin surface of extracted human teeth. Using this new device, the fluid movement was measured and compared between before and after each agent was applied. The instrument was able to measure dentinal fluid movement with a high resolution (0.196 nL) and the flow occurred with a rate of 0.84 to 15.2 nL/s before treatment. After BisBlock or Clearfil SE Bond was used, the fluid movement was decreased by 39.8 to 89.6%.