• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2009년도 춘계 학술대회 제21권1호
• /
• pp.307-308
• /
• 2009

부산 롯데타운용 80MPa급 초고강도 콘크리트는 낮은 W/B와 높은 결합재량에 기인하여 수화생성 물이 증가하고, FA 및 BS의 포졸란 및 잠재수경성반응에 의하여 생성된 C-S-H겔이 공극구조를 개선함으로써 콘크리트 내부조직이 밀실하게 형성되어 탄산가스, 염화물 및 염소이온의 침투가 없는 것으로 나타나 내구성은 매우 우수한 것으로 판단된다.

• 콘크리트학회논문집
• /
• 제25권3호
• /
• pp.295-304
• /
• 2013

초고성능 콘크리트(UHPC: Ultra-High Performance Concrete)는 최근 국내외에서 연구가 가장 활발한 분야 중 하나로서 구조물의 장수명화와 경제성 제고에 기여하고 있다. 품질관리 및 공사기간 단축을 위해서는 공장에서 제작된 프리캐스트 방식의 초고성능 콘크리트가 유리하지만, 이 경우에도 프리캐스트 세그먼트 간의 이음부 등 부득이 현장타설로 시공되어야 하는 부분이 존재한다. 그러나 현장타설 시에는 공장 제작 시와는 달리 최적의 양생 조건을 구현하기 어려울 가능성이 크다. 따라서 이 연구에서는 현장에서 예상되는 여러 가지의 열악한 양생 조건을 가정하였을 때 초고성능 콘크리트의 압축강도 발현 경향을 실험적으로 규명하였다. 양생온도, 양생 전 지연시간, 양생 지속시간, 수분 공급 조건을 변수로 두어 공시체를 제작한 후 표준적인 고온습윤양생으로 제작된 공시체의 강도와 비교하였다. 실험 결과를 분석하여 현장에서 타설된 초고성능 콘크리트를 양생할 때 요구되는 최소한의 조건을 제안하였다. 이 연구를 통해 초고성능 콘크리트의 현장에서의 활용도를 더욱 높일 수 있을 것으로 기대된다.

• Structural Engineering and Mechanics
• /
• 제61권6호
• /
• pp.711-719
• /
• 2017

This study investigates the effects of reinforcing bar diameter and cover depth on the shrinkage behavior of restrained ultra-high-performance fiber-reinforced concrete (UHPFRC) slabs. For this, twelve large-sized UHPFRC slabs with three different rebar diameters ($d_b=9.5$, 15.9, and 22.2 mm) and four different cover depths (h=5, 10, 20, and 30 mm) were fabricated. In addition, a large-sized UHPFRC slab without steel rebar was fabricated for evaluating degree of restraint. Test results revealed that the uses of steel rebar with a large diameter, leading to a larger reinforcement ratio, and a low cover depth are unfavorable regarding the restrained shrinkage performance of UHPFRC slabs, since a larger rebar diameter and a lower cover depth result in a higher degree of restraint. The shrinkage strain near the exposed surface was high because of water evaporation. However, below a depth of 18 mm, the shrinkage strain was seldom influenced by the cover depth; this was because of the very dense microstructure of UHPFRC. Finally, owing to their superior tensile strength, all UHPFRC slabs with steel rebars tested in this study showed no shrinkage cracks until 30 days.

• Computers and Concrete
• /
• 제21권2호
• /
• pp.167-179
• /
• 2018

Reactive powder concrete (RPC) is a type of ultra-high strength cement-based material with a dense microstructure, which is made of ultra-fine powders. RPC demonstrate a very brittle behavior, thus adding fibers improves its mechanical properties. In this study, it was attempted to investigate the effect of using steel and polyvinyl alcohol (PVA) fibers as well as their combination on the properties of RPC. In this regard, hooked-end crimped steel fibers together with short PVA fibers were utilized. Steel and PVA fibers were used with the maximum volume fraction of 3% and 0.75%, respectively, and also different combinations of these fibers were used with the maximum volume fraction of 1% in the concrete mixes. In total, 107 concrete specimens were prepared, and the effect of fiber type and volume fraction on the physico-mechanical properties of RPC including compressive strength, tensile strength, modulus of elasticity, density, and failure mode was explored. In addition, the effect of the curing type on the properties of compressive strength, modulus of elasticity, and density of RPC was evaluated. Finally, coefficients for conversion of cubic compressive strength to cylindrical one for the RPC specimens were obtained under the two curing regimes of heat treatment and standard water curing.

• 콘크리트학회논문집
• /
• 제23권2호
• /
• pp.235-244
• /
• 2011

세그멘탈 교량의 파괴는 부적절한 접합에 의해 파괴를 일으키게 되는데 이는 세그멘탈 접합부를 가로지르는 횡방향 텐던의 부식을 야기하게 된다. 이 연구에서는 현장 타설 접합 및 에폭시 접합 조건에 따른 초고성능 프리캐스트 콘크리트 접합부에서의 전단키 거동을 전단 및 극한거동 측면에서 평가하였다. 또한, PC 세그멘탈 교량 접합부의 전단 거동을 파악하기 위하여 전단키 접합부의 전단 거동과 전단강도 특성을 실험적으로 연구하였다. 이 연구를 통하여 접합부 형상에 따른 하중-변위 관계, 균열 거동, 파괴 모드, 전단 강도 등을 구명하고, 접합부의 역학적 거동에 영향을 미치는 여러 인자들에 대해 분석한다. 또한 이로부터 최적의 접합부 형상을 도출하고, 이에 따른 최적의 접합 방식을 검토함으로서 접합부 설계의 지침과 해석의 근거를 제시하도록 한다.

• Structural Engineering and Mechanics
• /
• 제50권5호
• /
• pp.635-652
• /
• 2014

Creep and shrinkage behaviour of an ultra lightweight cement composite (ULCC) up to 450 days was evaluated in comparison with those of a normal weight aggregate concrete (NWAC) and a lightweight aggregate concrete (LWAC) with similar 28-day compressive strength. The ULCC is characterized by low density < 1500 $kg/m^3$ and high compressive strength about 60 MPa. Autogenous shrinkage increased rapidly in the ULCC at early-age and almost 95% occurred prior to the start of creep test at 28 days. Hence, majority of shrinkage of the ULCC during creep test was drying shrinkage. Total shrinkage of the ULCC during the 450-day creep test was the lowest compared to the NWAC and LWAC. However, corresponding total creep in the ULCC was the highest with high proportion attributed to basic creep (${\geq}$ ~90%) and limited drying creep. The high creep of the ULCC is likely due to its low elastic modulus. Specific creep of the ULCC was similar to that of the NWAC, but more than 80% higher than the LWAC. Creep coefficient of the ULCC was about 47% lower than that of the NWAC but about 18% higher than that of the LWAC. Among five creep models evaluated which tend to over-estimate the creep coefficient of the ULCC, EC2 model gives acceptable prediction within +25% deviations. The EC2 model may be used as a first approximate for the creep of ULCC in the designs of steel-concrete composites or sandwich structures in the absence of other relevant creep data.

• Steel and Composite Structures
• /
• 제49권4호
• /
• pp.381-392
• /
• 2023

This study experimentally investigates the flexural behavior of steel-UHPC composite slabs composed of an innovative negative Poisson's ratio (NPR) steel plate and Ultra High Performance Concrete (UHPC) slab connected via demountable high-strength bolt shear connectors. Eight demountable composite slab specimens were fabricated and tested under traditional four-point bending method. The effects of loading histories (positive and negative bending moment), types of steel plate (NPR steel plate and Q355 steel plate) and spacings of high-strength bolts (150 mm, 200 mm and 250 mm) on the flexural behavior of demountable composite slab, including failure mode, load-deflection curve, interface relative slip, crack width and sectional strain distribution, were evaluated. The results revealed that under positive bending moment, the failure mode of composite slabs employing NPR steel plate was distinct from that with Q355 steel plate, which exhibited that part of high-strength bolts was cut off, part of pre-embedded padded extension nuts was pulled out, and UHPC collapsed due to instantaneous instability and etc. Besides, under the same spacing of high-strength bolts, NPR steel plate availably delayed and restrained the relative slip between steel plate and UHPC plate, thus significantly enhanced the cooperative deformation capacity, flexural stiffness and load capacity for composite slabs further. While under negative bending moment, NPR steel plate effectively improved the flexural capacity and deformation characteristics of composite slabs, but it has no obvious effect on the initial flexural stiffness of composite slabs. Meanwhile, the excellent crack-width control ability for UHPC endowed composite members with better durability. Furthermore, according to the sectional strain distribution analysis, due to the negative Poisson's ratio effect and high yield strength of NPR steel plate, the tensile strain between NPR steel plate and UHPC layer held strain compatibility during the whole loading process, and the magnitude of upward movement for sectional plastic neutral axis could be ignored with the increase of positive bending moment.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.86-87
• /
• 2015

An active study on UHPC, which has been recently used in high-rise building and bridges, is in progress. However, research on bonding shear strength of UHPC is required to be studied due to the lack of information. In this study, experimental research progress for bonding shear strength (shear strength of adhesive surface) evaluation of UHPC (Ultra High Performance Concrete) is proceeded. First, specimens that surface treatment methods of concrete bonded section and retardation time of placement are considered are produced. Second, Direct Shear test is applied on concrete bonded section of UHPC. As a result of this study, the highest bonding shear strength specimen in which compared to the non-retardation time specimen is compaction turbulence treatment. From later study, it is judged that strength of UHPC in accordance with direction of steel fiber when steel fiber of UHPC is mixed.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.377-384
• /
• 2014

최근의 건축 구조물이 고층화, 대형화됨에 따라 초고강도 콘크리트의 적용 및 수요가 증가하고 있는 추세이나, 화재에 대한 취약성을 가지고 있는 초고강도 콘크리트의 열적 특성에 대한 검토는 아직 충분하지 않으며 이에 대한 성능 검토 또한 요구되고 있는 실정이다. 이에 이 논문에서는 초고강도 콘크리트의 고온 재료 모델 개발에 대한 기초적 자료를 제공하기 위하여 상온에서 $800^{\circ}C$까지의 고온 가열을 받은 100 MPa급 초고강도 콘크리트를 대상으로 가열온도의 변화에 따른 잔존압축강도, 탄성계수 및 응력-변형 성상, 반복하중 시의 응력-변형 성상 등 역학적 특성 변화를 확인하였다. 또한, TG/DTA분석과 SEM 촬영으로 콘크리트의 화학 물리적 특성을 확인하고 국내 외의 기존 연구와 비교 검토하였다. 그 결과, 가열온도 $300^{\circ}C$에서 잔존압축강도 및 탄성계수의 급격한 저하를 확인하였으며, 반복하중 하에서는 가열온도 $400^{\circ}C$부터 소성거동이 발생하는 것과 함께 단일하중과 거의 동일한 경향을 보임을 확인할 수 있었다. TG/DTA 분석 및 SEM 촬영을 실시한 결과와 기존 연구를 비교 검토한 결과, 콘크리트 내부 조직의 열화와 수분 증발 및 화학반응 등으로 인하여 잔존압축강도 및 탄성계수의 저하가 일어났음을 확인할 수 있었다.

• Computers and Concrete
• /
• 제26권3호
• /
• pp.275-283
• /
• 2020

Reinforced concrete (RC) does not provide sufficient resistance against impacts and blast loads, and the brittle structure of RC fails to protect against fractures due to the lack of shock absorption. Investigations on improving its resistance against explosion and impact have been actively conducted on high-performance fiber-reinforced cementitious composites (HPFRCCs), such as fiber-reinforced concrete and ultra-high-performance concrete. For these HPFRCCs, however, tensile strength and toughness are still significantly lower compared to compressive strength due to their limited fiber volume fraction. Therefore, in this study, the tensile behavior of slurry-infiltrated fiber-reinforced cementitious composites (SIFRCCs), which can accommodate a large number of steel fibers, was analyzed under static and dynamic loading to improve the shortcomings of RC and to enhance its explosion and impact resistance. The fiber volume fractions of SIFRCCs were set to 4%, 5%, and 6%, and three strain rate levels (maximum strain rate: 250 s^-1) were applied. As a result, the tensile strength exceeded 15 MPa under static load, and the dynamic tensile strength reached a maximum of 40 MPa. In addition, tensile characteristics, such as tensile strength, deformation capacity, and energy absorption capacity, were improved as the fiber volume fraction and strain rate increased.