• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.230-231
• /
• 2009

펄스 레이저 층착법 (이하 PLD)은 다성분계 산화물 박막 또는 다층구조의 박막 제작에 매우 유용한 기술이다. 본 실험에서는 KrF 엑시머 레이저를 이용하여 pt on Si 기판 위에 150nm 두께의 $Bi_{1.5}ZnNb_{1.5}O_7$(이하 BZN) 박막을 다양한 기판온도에서 제작하였다. XRD를 이용하여 BZN 박막의 구조적 특성을 분석하였고, 박막을 MIM 구조로 제작하여 유정적 특성을 측정하였다. 제조한 BZN 박막은 $500^{\circ}C$ 이상에서 결정질을, $500^{\circ}C$ 이하의 온도에서는 비정질 특성을 보였다. 유전 특성은 100 - 400$^{\circ}C$ 영역에서는 온도가 증가함에 따라 졸은 특성을 나타내었고, $500^{\circ}C$에서부터는 감소하였다. 증착 온도 $400^{\circ}C$에서 제작한 BZN 박막이 유전상수가 67.8, 유전 손실이 0.006으로 가장 줄은 유전특성을 나타내었다.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.340-345
• /
• 2003

B $i_2$ $O_3$-Ti $O_2$ composite dielectric ceramics have been prepared by a conventional solid state ceramic route. The composite ceramics were prepared with starting materials of different origin and the microwave dielectric properties were investigated. The sintered ceramics were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray microanalysis, Raman and microwave methods. Structural and microstructural analyses identified two separate phases: Ti $O_2$(rutile) and B $i_2$ $Ti_4$0$_{11}$. The separate grains of titania and bismuth titanate were distributed uniformly in the ceramic matrix. The composition 0.88Ti $O_2$-0.12B $i_2$ $Ti_4$ $O_{11}$ was found to have a Q$\times$f of 9300 GHz (measured at a frequency of 3.9 GHz), a temperature coefficient of frequency, $\tau$$_{cf}$ near zero and a high relative permittivity, $\varepsilon$r of 83. The microwave dielectric properties were measured down to 20$^{\circ}$K K. The quality factor increased on cooling the ceramic samples.les.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1552-1553
• /
• 2011

The HVDC transformer which is one of the main equipments for HVDC(High Voltage Direct Current) electric power transmission systems is exposed to not only AC voltage but also the inflowing DC voltage which comes from the DC-AC converter systems. Therefore, the HVDC transformer insulation system is required to withstand the electric field stress under AC, DC and DC polarity reversal conditions. However the electric field distributions under those conditions are different because the AC electric field and DC electric field are governed by permittivity and conductivity, respectively. In this study, the changes of electric potential and electric field of conventional AC transformer insulation system under DC polarity reversal test condition were analyzed by FEM(Finite Element Method). The DC electric field stress was concentrated in the solid insulators while the AC electric field stress was concentrated in the mineral oil. In addition, the electric stress under that condition which is affected by the surface charge accumulation at the interfaces between insulators was evaluated. The stress in some parts could be higher than that of AC and DC condition, during polarity reversal test. The result of this study would be helpful for the HVDC transformer insulation system design.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.18-22
• /
• 2013

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• Resources Recycling
• /
• v.13 no.6
• /
• pp.26-30
• /
• 2004

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.879-882
• /
• 1992

In order to study electrical properties of epoxy composites with various additives rates and curing conditions, dielectric measurements have been performed over a frequency range from 30 [Hz] to 3 [MHz] and a temperature range of 20[$^{\circ}C$]$\sim$180[$^{\circ}C$] The observed higher values of dielectric permittivity and loss In the case of filled epoxy are attributed to MWS polarization effect. The low temperature peak assigned to the $\beta$-relaxation process is attributed to the enhenced rotation of the methyl group attached to the main chain and the presence of filler. And the high temperature peak ($\alpha$-relaxation process)is associated with the segmental motion or glass transition process.

• Journal of Powder Materials
• /
• v.15 no.4
• /
• pp.292-296
• /
• 2008

The electromagnetic (EM) wave absorption properties of the $Fe_{73}Si_{16}B_7Nb_3Cu_1$ nanocrystalline powder mixed with 5 to 20 vol% of Ni-Zn ferrites has been investigated in a frequency range from 100MHz to 10GHz. Amorphous ribbons prepared by a planar flow casting process were pulverized and milled after annealing at 425 for 1 hour. The powder was mixed with a ferrite powder at various volume ratios to tape-cast into a 1.0mm thick sheet. Results showed that the EM wave absorption sheet with Ni-Zn ferrite powder reduced complex permittivity due to low dielectric constant of ferrite compared with nanocrystalline powder, while that with 5 vol% of ferrite showed relatively higher imaginary part of permeability. The sheet mixed with 5 vol% ferrite powder showed the best electromagnetic wave absorption properties at high frequency ranges, which resulted from the increased imaginary part of permeability due to reduced eddy current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.45-48
• /
• 1998

A BaTiO$_3$ was annexed to SrTiO$_3$, (x)BaTiO$_3$-(1-x)SrTiO$_3$ (0.7$\leq$X$\leq$1) ceramics with stable dielectric and electrical properties in high voltage were manufactured. Structural, dielectric and electrical properties were surveyed with the contents of SrTiO$_3$. The open porosity and sintering density were excellent in 0.9BaTiO$_3$-0.1SrTiO$_3$, the grain size of 0.9BaTiO$_3$-0.1SrTiO$_3$ was maximum at 12.40[${\mu}{\textrm}{m}$]. Increasing SrTiO$_3$ mol ratio, the curie temperature was shifted low temperature and the supreme permittivity was increased. In line with increasing of supplied voltage, permitivity was decreased slightly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.42-45
• /
• 2001

The high permittivity are applied to DRAM and FRAM. (Ba,Sr)$TiO_3$ (EST) thin films were prepared by Sol-Gel method. BST solution was made and spin-coated on $Pt/SiO_2/Si$ substrate at 4000 [rpm] for 10 seconds in a time coating. Coated specimens were dried at $90[^{\circ}C]$ for 5 minutes. Coating process was repeated from 3 times to 5 times and then sintered at $750[^{\circ}C]$ for 30 minutes. Each specimen was analyzed structure and electrical characteristics. Thickness of BST ceramics thin films are about 2600-2800[$\AA$] in 3 times. Dielectric constant of thin films was little decreased at 1[KHz]~1[MHz]. Dielectric constant and loss to frequency were 250 and 0.02 in BST3. The property of leakage current was stable When the applied voltage was 0~3[V] Leakage current was $10^{9}\sim10^{11}$[A] at 0~3[V].

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.1
• /
• pp.48-58
• /
• 2015

The bandwidth enhancement of an aperture coupled microstrip patch antenna(ACMPA) with a high permittivity feed substrate suitable for the integration with MMIC is investigated using variation of an aperture width. As an aperture width increases, the 10 dB return loss bandwidth increases due to the increase of the mutual resonance region between a patch resonance and an aperture resonance. The bandwidth of an ACMPA with extended aperture width is increased up to 35.3 % from 20.8 % of the ACMPA with an aperture of a typical aspect ratio 10:1. The degradation of the radiation characteristics of an ACMPA due to the increase of an aperture width is very small.