• Plant Resources
• /
• 제5권3호
• /
• pp.214-223
• /
• 2002

The objective of this study was to understand the conservation of gene resources and provide information for mass selection' of winter bud characters among the selected populations of Kalopanax septemlobus Koidz using analysis of variance(ANOVA) tests. The obtained results are shown below; 1. Ten populations of K. septemlobus were selected for the study of the variation of winter bud characters in Korea. The results of the analysis of variance(ANOVA) tests shows that there were statistically significant differences in all of the winter bud characters among those populations. 2. Correlation analysis shows that width between Height and DBH(Diameter at breast height) characters have negative relationship with all of the characters, as ABL(Apical branch length), ABW(Apical branch width), AWBL(Apical branch winter bud length), AWBW(Apical branch winter bud width), ABT(Apical branch No. of thorns), ABLB(Apical branch No. of lateral bud) and LBL(Lateral branch length), LBW(Lateral branch width), LBT(Lateral branch No. of thorns), LBLB(Lateral branch No. of lateral bud). 3. The result of principal component analysis(PCA) for winter buds showed that the first principal components(PC' s) to the fourth principal component explains about 78% of the total variation. The first principal component(PC) was correlated with AWBW, LWBW, and LBL and the ratio of ABL/ABW and LBL/LBW out of 16 winter bud characters. The second principal component correlated with ABL, ABW, ABLB, LWBL(Lateral branch winter bud length), and LBW and the ratio of AWBL/AWBW. The third principal component correlated with ABL, ABW, LWBL, LBL, and the ratio of LBL/LBW. The fourth principal component correlated with LBL and the ratio of LWBL/LWBW(Lateral branch winter bud width), LBL/LBW. Therefore, these characters were important to analysis of the variation for winter bud characters among selected populations of K. septemlobus in Korea. 4. Cluster analysis using the average linkage method based on 10 selected populations for the 16 winter bud characters of K. septemlobus in Korea showed a clustering into two groups by level of distance 1.1(Fig. 3). As can be seen in Fig. 3, Group I consisted of three areas(Mt. Sori, Mt. Balwang and Mt. Worak) and Group Ⅱ contisted of seven areas(Suwon, Mt. Chuwang, Mt. Kyeryong, Mt. Kaji, Mt. Jiri, Muan, and Mt. Halla). The result of cluster analysis for winter bud characters corresponded well with principal component analysis, as is shown in Fig. 2.

• Ocean and Polar Research
• /
• 제32권3호
• /
• pp.247-254
• /
• 2010

Single cell PCR analysis and light and scanning electron microscopic techniques were utilized to identify free living bivalve larvae in the coastal waters of Tae-an, on the west coast of Korea. Through DNA sequencing, venerid clam larvae were isolated and identified as Ruditapes philippinarum (99% similarity) and Meretrix lusoria (99%). Under microscopic observation, the D-veliger stage of R. philippinarum exhibited symmetrical shoulder angles and an elliptical ventral form. In contrast, M. lusoria displayed asymmetrical shoulder angles and a round ventral form in the umbonal stage. Size of the R. philippinarum larvae was $156{\pm}22{\mu}m$ in length, $126{\pm}12{\mu}m$ in height, $92{\pm}14{\mu}m$ in width with a length: height ratio of 1.23. Meretrix lusoria was $202{\pm}44{\mu}m$ in length, $161{\pm}35{\mu}m$ in height, $96{\pm}38{\mu}m$ in width with a length: height ratio of 1.25. Experimental results indicate that morphological and molecular characteristics provide evidence for the larval identification of these two venerid clam larvae species in nature.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.132-139
• /
• 2000

This paper reports a novel micromachining process based on UV-LIGA process and (110) silicon anisotropic etching for fabrication of a high-aspect-ratio comb actuator. The comb electrodes are fabricated by (110) SILICON comb structure considering the etch-rate-ratio between (110) and (111) planes and lateral etch rate of a beam-type structure. The fabricated structure was$ 400\mum \; thick\; and\; 18\mum$ wide comb electrodes separated by $7\mim$ so that the height-gap ratio was about 57. Also considering resonant frequency of the comb actuator and the frequency-matching between sensing and driving mode for gyroscope application, we designed the number, width, height and length of the spring structures. Electroplated gold springs on both sides of the seismic mass were $15\mum\; wide,\; 14\mum\; thick\; and \; 500\mum$ long. The fabricated comb actuator had resonant frequency ay 1430Hz, which was calculated to be 1441Hz. The proposed fabrication process can be applicable to the fabrication of a high-aspect-ratio comb actuator for a large displacement actuator and precision sensors. Moreover, this combined process enables to fabricate a more complex structure which cannot be fabricate only by surface or bulk micromachining.

• 대한토목학회논문집
• /
• 제30권3A호
• /
• pp.241-256
• /
• 2010

본 연구에서는 변장비 70에 가까운 도전적인 현수교 단면을 개발하는데 목적을 두고 있다. 이를 위하여 먼저 강박스 현수교의 제원을 수집 분석하였다. 그 결과를 보면 강박스 현수교에서 경간장과 형상변수(교폭, 형고, 변장비, 고폭비)는 상관관계가 낮았고 고유진동수와 형상변수의 상관관계도 낮은 것으로 나타났으며, 상관관계가 높은 경간장과 고유진동수 관계는 신뢰구간별 추정식을 제시하였다. 그리고 교폭, 진동수비, 질량, 질량관성모멘트, 수직 및 비틈 고유진동수 변화에 따른 플러터 풍속의 민감도 분석을 실시하였는데, 타 변수보다 비틈 고유진동수가 플러터 풍속에 미치는 영향이 가장 큰 것으로 나타났다. 주경간장 1111 m인 현수교의 내풍 단면을 개발하기 위하여 최소 단면폭과 형고를 제약조건으로 하여 총 30개의 단면에 대한 풍동실험을 실시하고, 이로부터 한계풍속 기준을 충분히 만족하는 단면을 찾았다. 그리고 다중모드 플러터 해석으로 개발한 단면의 내풍안정성을 검증하였다. 본 연구에서 제시한 세장 단면은 향후 장대 현수교 설계시 활용할 수 있을 것으로 판단된다.

• 대한기계학회논문집B
• /
• 제24권5호
• /
• pp.744-752
• /
• 2000

The influence of arrangement and length of discrete ribs on heat/mass transfer and friction loss is investigated. Mass transfer experiments are conducted to obtain the detailed local heat/mass transfer information on the ribbed wall. The aspect ratio (width/height) of the duct is 2.04 and the rib height is one tenth of the duct height, such that the ratio of the rib height to hydraulic diameter is 0.0743. The ratio of rib-to-rib distance to rib height is 10. The discrete ribs were made by dividing each continuous rib into 2, 3 or 5 pieces and attached periodically to the top and the bottom walls of the duct with a parallel orientation The combined effects of rib angle and length of the discrete ribs on heat/mass transfer ae considered for the rib angles $({\alpha})\;of\;90^{\circ}\;and\;45^{\circ}$. As the number of the discrete ribs increases, the uniformity of the heat/mass transfer distributions increases. For $(\alpha})=90^{\circ}$, the heat/mass transfer enhancement with the discrete ribs is remarkable, while the heat/mass transfer performances are slightly higher than that of the transverse continuous ribs due to the accompanied high friction loss penalty. For $(\alpha})=90^{\circ}$, the average heat/mass transfer coefficients and the heat/mass transfer performances decrease slightly with the discrete ribs compared to the case of the angled continuous ribs.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.293-298
• /
• 2011

The most widely used method to form an electrode in industrial solar cells are screen printing. Screen printing is characterized by a relatively simple and well-known production sequence with high throughput rates. However the method is difficult to implement a fine line width of high-efficiency solar cells can not be made. The open circuit voltage(Voc) and the short circuit current density(Jsc) and fill factor(FF) need to be further improved to increase the efficiency of silicon solar cells. In this study, gravure offset printing method using the multicrystalline-silicon solar cells were fabricated. Gravure off-set printing method which can print the fine line width of finger electrode can have the ability reduce the shaded area and increase the Jsc. Moreover it can make a high aspect ratio thereby series resistance is reduced and FF is increased. Approximately $50{\mu}m$ line width with $35{\mu}m$ height was achieved. The efficiency of gravure off set was 0.7% higher compare to that of scree printing method.

• 한국환경과학회지
• /
• 제30권9호
• /
• pp.709-717
• /
• 2021

This study evaluated the growth, physiological responses and productivity based on the intercropping ratio of cherry tomato (Lycopersicon esculentum L.) with basil (Ocimum basilicum L.). on the rooftops to determine out the efficient ratio in urban agriculture. From April to September 2019, an experiment was conducted on the rooftop of Konkuk University Glocal Campus. Cherry tomato and basil were selected as companion plants for eco-friendly urban agriculture on the rooftops. Each plot was created with a width of 100 cm, length of 100 cm, and height of 25 cm. After installing drainage and waterproof layers from bottom to top, substrate was laid out with a height of 20 cm. Intercropping ratio was consisted of a single tomato plant (TC), 2:1 tomato to basil (T₂B₁), 1:1 tomato to basil (T₁B₁), 1:2 tomato to basil 2 (T₁B₂), and a single basil plant (BC), were conducted using a randomized complete plot design with five treatments and three replication (a total 15 plots). Measurements were divided into growth, physiological responses, and productivity parameters, and detailed items were investigated and analyzed by classifying them into plant height, leaf length, leaf width, number of leaves, root length, root collar caliper, chlorophyll contents, fresh weight, dry weight, number of fruit, fruit caliper, fruit weight, and sugar content. Comparative analyses of cherry tomato with basil plants by intercropping ratio, growth, physiological, and productivity responses are determined to be efficient when the ratio of cherry tomato to basil ratio is 2:1 or 1:1.

• 한국자원식물학회지
• /
• 제22권4호
• /
• pp.299-303
• /
• 2009

넓은잎큰조롱의 두둑높이에 따른 생산성 및 품질향상을 위하여 재배법 확립의 기초자료로 제공하고자 두둑높이를 달리하여 2005년부터 3년간 시험한 결과, 만장, 엽장, 엽폭, 엽수, 엽록소함량, 경엽 건물중은 두둑높이가 높을수록 양적인 증가를 가져왔으나, 경태와 분지수는 두둑높이가 낮을수록 굵거나, 많은 경향이었다. 근수와 근장은 두둑높이 20 cm까지는 두둑높이가 높을수록 많거나, 길었으나, 20 cm 이상의 두둑높이에서는 생육량이 감소하였으며, 근태는 두둑높이가 낮을수록 굵어지는 경향이었다. 비상품근 중 세근은 두둑높이 20 cm에서 다소 많았으며, 부패근은 두둑높이가 낮을수록 많은 경향이었고, 근수량은 두둑높이 20 cm내지 30 cm 까지는 두둑높이가 높을수록 증수되어 두둑높이 10 cm의 515 kg/10a 대비 3%, 11% 증수되었다.

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.1-8
• /
• 2007

The present research is based upon the numerical analysis of a car windshield in order to represent the optimum design guide to improve the overall defrosting performance of the system. First, the control factors that highly affect the defrosting performance of a car windshield are chosen and afterwards, the optimum variables of each control factor are extracted out to analyze its performance. The main control factors for this research are respectively, the air injection angle of a defroster nozzle, the height of a nozzle outlet, and the ratio of the width to the height of a nozzle outlet. For such case when the air inlet angle is relatively small, the flow near the vicinity of the inner face of a windshield tends to expand. As a consequence, the heat transfer rate through the windshield decreases. Also, the height of a nozzle outlet is recommended to maintain its size to minimum. However, when the ratio mentioned before is designed less than unity, the defrosting performance decreases.

• 대한기계학회논문집B
• /
• 제28권9호
• /
• pp.1022-1031
• /
• 2004

The commutation errors by the filtering process in the large eddy simulation are considered. It is compared the conventional filter with the inhomogeneous filter that is devised to reduce the commutation errors. The weighting factor of the inhomogeneous filter suggested by Vasilyev is adopted. Also, using the optimizing function that estimates test filter width to eliminate the dissipations in the region excluding the vicinity of the wall, the flow patterns are analyzed. It is evaluated in simulations of the turbulent channel flow at Reynolds number of 1020, based on friction velocity and channel half height. Results show that the commutation errors can be significantly reduced by using the inhomogeneous filter and the optimized test filter width.