• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.4
• /
• pp.615-624
• /
• 2011

last few decades. In this study, the lyophilized cells of Pleurotus eryngii (mushroom) were used as an inexpensive biosorbent for Cd(II) and Pb(II) removal from aqueous solutions. The effect of various physicochemical factors on Cd(II) and Pb(II) biosorption such as pH (2.0-7.0), initial metal concentration ($0.0-300mg\;L^{-1}$), temperature, fungal biomass and contact time (0-120 min) were studied. Optimum pH for removal of Cd(II) and Pb(II) was 6.0, and the contact time was 45 min at room temperature. The nature of biosorbent and metal ion interaction was evaluated by Infrared (IR) spectroscopic technique. IR analysis of mushroom biomass revealed the presence of amino, carboxyl, hydroxyl and methyl groups, which are responsible for biosorption of Cd(II) and Pb(II). The maximum adsorption capacities of P. eryngii for Pb(II) and Cd(II) calculated using Langmuir adsorption isotherm were 82.0 and $16.13mg\;g^{-1}$, respectively. The adsorption isotherms for two biosorbed heavy metals were fitted well with Freundlich isotherm as well as Langmuir model with correlation coefficient ($r^2$>0.99). Thus, this study indicated that the P. eryngii is an efficient biosorbent for the removal of Cd(II) and Pb(II) from aqueous solutions.

• Mycobiology
• /
• v.49 no.5
• /
• pp.507-520
• /
• 2021

Papiliotrema huenov was previously reported to be highly tolerant of a range of extremely toxic heavy metals. This study aimed to identify the potential of P. huenov to remove manganese and copper from aqueous solution. Physical conditions which affect removal of Mn(II) and Cu(II) were determined. Optimal temperature for adsorption of both metal ions was 30 ℃, and optimal pH for maximum uptake of Mn(II) and Cu(II) were 5 and 6, respectively. Under these conditions, living cells of P. huenov accumulated up to 75.58% of 110 mg/L Mn(II) and 70.5% of 128 mg/L Cu(II) over 120 h, whereas, the removal efficiency of metal ions by dead cells over 1 h was 60.3% and 56.5%, respectively. These results indicate that living cells are more effective than dead biomass for bioremediation, but that greater time is required. The experimental data extends the potential use of P. huenov in biosorption and bioaccumulation of toxic heavy metals to copper and manganese, two of the most common industrial contaminants.

• Economic and Environmental Geology
• /
• v.43 no.6
• /
• pp.555-564
• /
• 2010

Remediation process by using the bio-carrier (beads) with dead Bacillus sp. B1 and polysulfone was investigated for heavy metal contaminated groundwater. Sorption batch experiments using the bio-carrier were performed to quantify the heavy metal removal efficiencies from the contaminated solution. The analyses using SEM/EDS and TEM for the structure and the characteristic of precipitates on/inside the beads were also conducted to understand the sorption mechanism by the bio-carrier. Various amounts of freeze-dried dead Bacillus sp. B1 were mixed with polysulfone + DMF(N,N-dimethylformamide) solution to produce the bio-carrier (beads; less than 2mm in diameter) and 5% of Bacillus sp. B1 in the bio-carrier was optimal for Pb removal in the solution. The removal efficiency ratings of the bio-carrier for Pb, Cu and Cd were greater than 80% after adding 2g of bio-carrier in 50ml of aqueous solution (<10mg/L of each heavy metal concentration). Reaction time of the bio-carrier was very fast and most of the sorption reaction for heavy metals were completed within few hours. Batch experiments were duplicated at various pH conditions of aqueous solutions and Cu and Pb removal efficiencies highly maintained at wide pH ranges (pH 2-12), suggesting that the bio-carrier can be useful to clean up the acidic waste water such as AMD. From SEM/EDS and TEM analyses, it was observed that the bio-carrier was spherical shape and was overlapped by many porous layers. During the sorption experiment, Pb was crystallized on the surface of porous layers and also was mainly concentrated at the boundary of Bacillus sp. B1 stroma and polysulfone substrate, showing that the main mechanism of the bio-carrier to remove heavy metals is the sorption on/inside of the bio-carriers and the bio-carriers are excellent biosorbents for the removal of heavy metal ions from groundwater.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.271-275
• /
• 2005

Pine bark, chinese cabbage, crap shell which are used for removing metal ions from aqueous solutions. The removal of metal ions from aqueous solution by adsorption and ion exchange on bio residues was studied. Biosorption of $Cu^{2+},\;Ni^{2+},\;Pb^{2+}$ were compared. Adsorption ability different for the factors [adsorption time, adsorbent weight, initial concentration] and all experiments pH variation were investigated. It was shown that chinese cabbage has higher metal removal ability than other materials The pH variation of metal solution were investigated according to the influences of the initial concentration and weight adsorbents.

• Journal of Food Hygiene and Safety
• /
• v.19 no.3
• /
• pp.132-139
• /
• 2004

As measure against the environmental pollution, maximum efforts to improve of the environmental pollution have also been made; removal of the contaminated sediments of the bay and the coastal area, monitoring of several heavy metal levels in fishes, shell fishes, sea water and sediment, and so on. The objective of this research is to investigate how much metals are included in the sea water, sediment, fishes and shell fishes in kyeongnam coastal area. Specifically, we are investigating the relationships between the metal included in fishes and sea water, and shell fishes and sediment, and heavy metals and heavy metals respectively. Heavy metal over the studied component and area, the average concentrations of Pb, Cd, Cr and Hg in sea water were 0.0029 mg/L, 0.005 mg/L, 0.0016 mg/L and ND, those of sediment were 11.9583 mg/kg, 0.2136 mg/kg, 1.9158 mg/kg and Hg 0.0108 mg/kg, those of fishes were 0.4358 mg/kg. 0.0726 mg/kg, 1.1188 mg/kg and Hg 0.0622 mg/kg, and those of shellfishes were Pb 0.6738 mg/kg, Cd 0.2223 mg/kg, Cr 0.5516 mg/kg and Hg 0.0117 mg/kg respectively. In the relationship test, Cd was significant in the relationship between fishes and sea water, and Hg was significant in the relationship between sediment and shellfishes.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 1998.10a
• /
• pp.2-4
• /
• 1998

Proliferation of Nocardia amarae cells in activated sludge has often been associated with the generation of nuisance foams. Despite intense research activities in recent years to examine the causes and control of Nocardia foaming in activated sludge, the foaming continued to persist throughout the activated sludge treatment plants in United States. In addition to causing various operational problems to treatment processes, the presence of Nocardia may have secondary effects on the fate of heavy metals that are not well known. For example, for treatment plants facing more stringent metal removal requirements, potential metal removal by Nocardia cells in foaming activated sludge would be a welcome secondary effect. In contrast, with new viosolid disposal regulations in place (Code o( Federal Regulation No. 503), higher concentration of metals in biosolids from foaming activated sludge could create management problems. The goal of this research was to investigate the metal sorption property of Nocardia amarae cells grown in batch reactors and in chemostat reactors. Specific surface area and metal sorption characteristics of N. amarae cells harvested at various growth stages were compared. Three metals examined in this study were copper, cadmium and nickel. Nocardia amarae strain (SRWTP isolate) used in this study was obtained from the University of California at Berkeley. The pure culture was grown in 4L batch reactor containing mineral salt medium with sodium acetate as the sole carbon source. In order to quantify the sorption of heavy metal ions to N amarae cell surfaces, cells from the batch reactor were harvested, washed, and suspended in 30mL centrifuge tubes. Metal sorption studies were conducted at pH 7.0 and ionlc strength of 10-2M. The sorption Isotherm showed that the cells harvested from the stationary and endogenous growth phase exhibited significantly higher metal sorption capacity than the cells from the exponential phase. The sequence of preferential uptake of metals by N. amarae cells was Cu>Cd>Ni. The specific surFace area of Nocardia cells was determined by a dye adsorption method. N.amarae cells growing at ewponential phase had significantly less specific surface area than that of stationary phase, indicating that the lower metal sorption capacity of Nocardia cells growing at exponential phase may be due to the lower specific surface area. The growth conditions of Nocardia cells in continuous culture affect their cell surface properties, thereby governing the adsorption capacity of heavy metal. The comparison of dye sorption isotherms for Nocardia cells growing at various growth rates revealed that the cell surface area increased with increasing sludge age, indicating that the cell surface area is highly dependent on the steady-state growth rate. The highest specific surface area of 199m21g was obtained from N.amarae cell harvested at 0.33 day-1 of growth rate. This result suggests that growth condition not only alters the structure of Nocardia cell wall but also affects the surface area, thus yielding more binding sites of metal removal. After reaching the steady-state condition at dilution rate, metal adsorption isotherms were used to determine the equilibrium distributions of metals between aqueous and Nocardia cell surfaces. The metal sorption capacity of Nocardia biomass harvested from 0.33 day-1 of growth rate was significantly higher than that of cells harvested from 0.5- and 1-day-1 operation, indicatng that N.amarae cells with a lower growth rate have higher sorpion capacity. This result was in close agreement with the trend observed from the batch study. To evaluate the effect of Nocardia cells on the metal binding capacity of activated sludge, specific surface area and metal sorption capacity of the mixture of Nocardia pure cultures and activated sludge biomass were determined by a series of batch experiments. The higher levels of Nocardia cells in the Nocardia-activated sludge samples resulted in the higher specific surface area, explaining the higher metal sorption sites by the mixed luquor samples containing greater amounts on Nocardia cells. The effect of Nocardia cells on the metal sorption capacity of activated sludge was evaluated by spiking an activated sludge sample with various amounts of pre culture Nocardia cells. The results of the Langmuir isotherm model fitted to the metal sorption by various mixtures of Nocardia and activated sludge indicated that the mixture containing higher Nocardia levels had higher metal adsorption capacity than the mixture containing lower Nocardia levels. At Nocardia levels above 100mg/g VSS, the metal sorption capacity of activate sludge increased proportionally with the amount of Noeardia cells present in the mixed liquor, indicating that the presence of Nocardia may increase the viosorption capacity of activated sludge.

• Journal of Environmental Science International
• /
• v.17 no.10
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.29-50
• /
• 2003

Physicochemical Properties of acid mine water of the Chonam-ri Creek and the Sagok-ri Creek in the Kwangyang Au-Ag mine area were determined using geochemical approaches. Metal contamination (Cd, Cu, Pb, Zn) is more serious in the Chonam-ri Creek than in the Sagok-ri Creek. However, the contents of Al and Fe is higher in the Sagok-ri Creek. Such differences between the two creeks probably reflect the abundance and composition of ore minerals. The attenuation processes for acid mine water in both creeks were investigated. In the Chonam-ri Creek, a small retention pond which contains limestone plays an important role in the removal of heavy metals by adsorption or coprecipitation due to increase of pH. The capacity of metal scavenging in this pond depends on the seasonal variation of inflow volume. Reddish yellow precipitates sampled in the Chonam-ri Creek were analyzed by XRD, SEM-EDS, EPMA, and chemical decomposition. The precipitates mainly consist of goethite and are also enriched in Al, Mn, Cu and Zn. This inditates that precipitation of goethite is important for scavenging those trace elements, possibly due to adsorption or coprecipitation. In the Sagok-ri Creek, on the other hand, hydrologic mixing of uncontaminated tributaries results in removal of heavy metals with iron hydroxides precipitation due to the pH increase. The mechanisms proposed for metal attenuation at the confluence between contaminated mine water and uncontaminated tributary water are also explained by the property-property plots.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.3
• /
• pp.310-315
• /
• 2011

BACKGROUND: Heavy-metal pollution represents an important environmental problem due to the toxic effects of metals, and their accumulation throughout the food chain leads to serious ecological and health problems. METHODS AND RESULTS: Optimum conditions in continuous-flow stirred tank reactor (CSTR) and packedbed column contactor (PBCC) using brown seaweed biosorbent were investigated. Under optimum conditions from both lab-scale biosorbent systems, removal efficiency of copper (Cu) in a large-scale PBCC system was investigated. Removal capacity of Cu using brown seaweed biosorbent in a lab-scale CSTR system was higher than that in a lab-scale PBCC system. On the other hand, over 48 L/day of flow rate in Cu solution, removal efficiency of Cu in a lab-scale PBCC system was higher than that in a lab-scale CSTR system. Optimum flow rate of Cu was 24 L/day, optimum Cu solution concentration was 100 mg/L. Removal capacity of Cu at different stages was higher in the order of double column biosorption system > single column biosorption system. Under different heavy metals, removal capacities of heavy metal were higher in the order of Pb > Cr > Ni > Mn ${\geq}$ Cu ${\geq}$ Cd ${\fallingdotseq}$ Zn ${\geq}$ Co. Removal capacity of Cu was 138 L in a large-scale PBCC system. Removal capacity of Cu a large-scale PBCC system was similar with in a lab-scale PBCC system. CONCLUSION(s): Therefore, PBCC system using brown seaweed biosorbent was suitable for treating heavy metal wastewater.

• Journal of Environmental Science International
• /
• v.14 no.7
• /
• pp.691-697
• /
• 2005

Waste sludge may be used to recovery wastewater contaminated with heavy metals. The waste sludge is an inexpensive readily available source of biomass for biosorption with metal-bearing wastewater. The biosorption of heavy metals such as Pb(II), Cu(II), Cr(II), and Cd(II) onto waste sludge was investigated in batch ex­periments and waste sludge loaded heavy metals was separated by dissolved air flotation. The biosorption equi­bria of heavy metals could be described by Langmuir and Freundich isotherms. The adsorption capacity for waste sludge was in the sequence of Pb(II)>Cr(II)>Cu(II)>Cd(II). The system attained equilibrium about 20 min. The Langmuir and Freundlich adsorption model effectively described the biosorption equilibrium of Cu(II) and Cr(II) ions on waste sludge. Maximum adsorption capacity of Cu(II) and Cr(II) were 196.08 and 158.73 mg/g, respectively. Solid-liquid separation efficiencies were kept above $95\%$ on waste sludge loaded heavy metals, and were decreased with pH increasing.