• 동력기계공학회지
• /
• 제12권5호
• /
• pp.27-33
• /
• 2008

Natural gas has been considered one of the most promising alternative fuels for transportation because of its abundance as well as its ability to reduce regulated pollutants. We measured emission characteristics of nanoparticles from lean burn H/D(Heavy-Duty) CNG (Compressed Natural Gas) engine equipped with oxidation catalysts. The experiments were carried out to measure the emission and engine performance according to the ESC test cycle. The CO and THC conversion efficiencies on the best catalyst in the ESC test cycle achieved about 91 % and 83 %, respectively. From the measurement by the SMPS, the number of nanoparticles emitted from H/D CNG engine is reduced by about 99 % which is more than that of 2.5 L diesel engine. The particle number concentrations of H/D CNG engine were almost nanoparticles. Nanoparticles smaller than 30 nm emitted from the H/D CNG engine and diesel engine equipped with a CDPF(Catalyzed Diesel Particulate Filter) were quite similar. However, the particles bigger than 30nm from the CNG engine were smaller than the particles from diesel engine equipped with a CDPF. The higher the CNG engine load, the lower the particle number from engine-out, but it increased slightly at full load.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권1호
• /
• pp.26-33
• /
• 2007

The intake swirl motion, as one of dominant effects for an engine combustion. is very effective for turbulence enhancement during the compression process in the cylinder of 2-valve engine. Because the combustion flame speed is determined by the turbulence that is mainly generated from the mean flow of the charge air motion in intake port system. This paper describes the experimental results of swirl flow and combustion characteristics by using the oil spot method and back-scattering Laser Doppler velocimeter (LDV) in 2-valve single cylinder transparent LPG engine using the liquid phase LPG injection. For this. various intake port configurations were developed by using the flow box system and swirl ratios for different intake port configurations were determined by impulse swirl meter in a steady flow rig test. And the effects of intake swirl ratio on combustion characteristics in an LPG engine were analyzed with some analysis parameters that is swirl ratio. mean flow coefficient, swirl mean velocity fuel conversion efficiency. combustion duration and cyclic variations of indicated mean effective pressure(IMEP). As these research results, we found that the intake port configuration with swirl ratio of 2.0 that has a reasonable lean combustion stability is very suitable to an $11{\ell}$ heavy-duty LPG engine with liquid phase fuel injection system. It also has a better mean flow coefficient of 0.34 to develope a stable flame kernel and to produce high performance. This research expects to clarify major factor that effects on the design of intake port efficiently with the optimized swirl ratio for the heavy duty LPG engine.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.193-201
• /
• 2014

A numerical study has been carried out to analyze the combustion characteristics in heavy duty diesel engine with post injection for reducing NO emission. For verification of numerical study results, calculated cylinder pressure was matched to experimental data. In this study, post injection timing and amount of post injection were modified as parameters, but the total amount of injection fuel was maintained. As the results, maximum cylinder pressure increases above minimum 2% by post injection and end of pressure curve is decreased rapidly. The more dwell time and amount of post injection fuel are, the more pressure drop occurs. And trade-off relation of NO and soot are appeared. In the results, NO was reduced without deterioration of cylinder pressure under condition of $10^{\circ}$ CA dwell time and main 60%, post 40% fuel portion.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.114-118
• /
• 2004

This research focused on the principle and the development of continuous regeneration DPF technology which was the best particulate matters removing technology of current existing technologies owing to its superior comparability and possible applicability. In addition, there were some discussions about the affecting engine parameters such as engine driving conditions and the amounts, velocity, temperature, pressure of exhaust emissions as well as sulfur contents and lubricants which were prerequisites to prevent poisoning effect on catalysts. The test was made on an 8000cc heavy-duty turbo diesel engine on which continuous regeneration DPF was in order to investigate regeneration characteristics of DPF and me performance under the condition of standard or 50ppm low sulphur diesel. Exhaust emissions, CO, HC, NOx PM were measured and compared under D-13 modes.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 2000년도 추계학술발표회 논문집
• /
• pp.137-142
• /
• 2000

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.23-32
• /
• 2002

Combustion and flame propagation characteristics of the liquid phase LPG injection (LPLI) engine were investigated in a single cylinder optical engine. Lean bum operation is needed to reduce thermal stress of exhaust manifold and engine knock in a heavy duty LPG engine. An LPLI system has advantages on lean operation. Optimized engine design parameters such as swirl, injection timing and piston geometry can improve lean bum performance with LPLI system. In this study, the effects of piston geometry along with injection timing and swirl ratio on flame propagation characteristics were investigated. A series of bottom-view flame images were taken from direct visualization using an W intensified high-speed CCD camera. Concepts of flame area speed, In addition to flame propagation patterns and thermodynamic heat release analysis, was introduced to analyze the flame propagation characteristics. The results show the correlation between the flame propagation characteristics, which is related to engine performance of lean region, and engine design parameters such as swirl ratio, piston geometry and injection timing. Stronger swirl resulted in foster flame propagation under open valve injection. The flame speed was significantly affected by injection timing under open valve injection conditions; supposedly due to the charge stratification. Piston geometry affected flame propagation through squish effects.

• 한국자동차공학회논문집
• /
• 제10권4호
• /
• pp.77-84
• /
• 2002

For the purpose of obtaining a fundamental data which is needed to develope the port injection type charged LPLi engine system, we manufactured intake port injection system of liquid charging LPG and modified heavy duty single cylinder LPLi engine from heavy duty diesel engine. Engine output and emission characteristics were analyzed under variable air/fuel ratio and charging pressure. Since LPG is consisted of propane and butane, we investigated combustion characteristics using this two kinds of fuel. From the result of charging engine performance test, engine torque increase about 30% ∼ 40% with 0.3bar charging pressure. In low speed condition, as charging pressure increase, combustion stability improve ill lean bum condition, but, in high speed condition, combustion stability make worse in lean bum condition. We know that engine output decreased rapidly from the condition of air excess ratio 1.3. In addition, we measured emission characteristics under the lean bum and charging condition. From this experiment, we found that CO emission is out of the question in the range from stiochiometric to lean burn and charging condition, but charging pressure has influence on HC emission.

• 한국대기환경학회지
• /
• 제13권6호
• /
• pp.487-495
• /
• 1997

The most desirable diesel oxidation catalyst (DOC) should have the properties of oxidizing CO, HC and SOF effectively at low exhaust gas temperature while minimizing the formation of sulfate at high exhaust gas temperature. Precious metals such as platinum and palladium have been known to be sufficiently active for oxidizing SOF and also to have high activity for the oxidation of sulfur dioxide $(SO_2)$ to sulfur trioxide $(SO_3)$. There is a need to develop a highly selective catalyst which can promote the oxidation SOF efficiently, on the other hand, suppress the oxidation of $SO_2$. In this study, a Pt-V catalyst was prepared by impregnating platinum and vanadium onto a Ti-Si wash coated ceramic monolith substrate. A prepared Pt-V catalytic converter was installed on a heavy duty diesel engine and the effect of fuel sulfur on particulate matter (PM) of heavy duty diesel engine was measured. The effect of fuel sulfur on PM of Pt-V was also compared with that of a commercialized Pt catalyst currently being used in some of the heavy duty diesel engines in advanced countries. Only 1 $\sim$ 3% of sulfur in the diesel fuel was converted to sulfate in PM for the engine without catalyst, but almost 100% of sulfur conversion was achieved for the engine with Pt catalyst at maximum loading condition. In the case of Pt-V catalyst, there was no big difference in conversion with the base engine even at maximum loading condition. The reason of SOF increase according to the increase of suflate emission was identified as the washing off effect of bound water in sulfate.

• 에너지공학
• /
• 제11권2호
• /
• pp.160-165
• /
• 2002

LPG 연료를 사용하는 대형 단기통엔진은 연소과정과 배기성능을 파악하기 위해서 설계.제작되었다. 실린더헤드와 피스톤 크라운은 LPG 연소를 위해서 변경되었다. 또한 플라이휠은 단기통엔진의 진동을 최소로 하기 위해서 제작되었다. 실험용 단기통엔진의 실린더내경과 행정은 각각 130mm와 140mm이다. 압축비는 피스톤 크라운 형상을 다르게 하여 8에서 9로 변경되었다. 본 연구를 위해서 제작된 단기통엔진은 1,000rpm에서 운전되었다. 본 연구의 주요 결론은 (1)제작된 엔진의 출력은 3가지 다른 압축비별로 당량비 1.0에서 최고를 나타낸다. (2) 압축비 증가에 따라서 출력이 약간 증간한다. (3) 최적 점화시기는 크랭크각으로 2에서 10까지 압축비의 증가와 함께 지각되어진다.

• 한국자동차공학회논문집
• /
• 제22권6호
• /
• pp.83-88
• /
• 2014

LTC(Low Temperature Combustion) technology has been studied to see feasibility of the combustion technology applied to heavy-duty engines on the laboratory scale. This study succeeded to develop a demo engine including realized low temperature combustion under partial load conditions. To find the best feasible LTC strategy, various LTC combustion methods such as PPCI, MK and highly diluted mixing controlled LTC were conducted on 6.0L heavy duty diesel engine. Air management system was re-designed to make these combustion scheme stable and the re-designed air system helped expand LTC operating range. This study finally revealed plausible LTC concept to maximize benefit of the alternative combustion technology while overcoming handicaps of the LTC strategy.