• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.303-306
• /
• 2003

To reduce the storage space of spent fuels used at the atomic power plants all over the world, the uranium elements contained in the spent fuels is being extracted and effectively stored. For this, the spent fuel are oxidized and deoxidized. In this study, it is produced conceptual design specification about the spent fuel management technology research and test facilities have been produced. The first considered processes in the facilities is the metal conversion furnace in the dry environment. Since this process is operates at the high temperature range, we have to consider heat-resisting designs for the device. For the heat-resisting designs, we have surveyed and analyzed technical references for material properties. Also, we have determined the temperature distribution condition of the device based on experimental results. We have calculated thermal stress and strain of each devices by the commercial analysis software, I-DEAS. By using the results, we have analyzed design configurations of the point at issue by thermal effects, and suggested alternative design configurations. It is experimented for inspecting confidence rate of heat strain. Based on these results, necessary design specifications for heat-resisting design have been produced.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2002년도 추계학술발표회요약집
• /
• pp.321.2-321
• /
• 2002

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권2호
• /
• pp.64-77
• /
• 1989

In this study, the experiments were carried out for the purpose of establishment of aluminium cementation to steel surface by diffusible heat treatment after making the coated film onto the substrate by arc spray method. Also, the microstructure and mechanical properties of the cementation layer produced by this study were inspected for various heat treatment and spraying conditions. Main results obtained are as follow ; 1. The coating film characteristics which have excellent errosion-resistance, high temperature oxidation-resistance are obtained by aluminium penetration heat treatment after making the sprayed aluminum coating film onto the steel substrate. 2. Aluminium diffusion penetration takes place at higher temperature than 660.deg.C, and the more heat treatment time and the higher heat treatment temperature adopted, the deeper diffusion layer obtained. 3. Insert gas arc spraying using argon gas as the carrier gas higher improvement of mechanical property than that of compressed air environment. 4. The coating film characteristics appeared to be improvement of adhesive property, porosity plugging effect by heat treatment in air environment.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.346-352
• /
• 2003

The study was performed to search on alternative material for turbopump parts made of Russian material by analyzing and comparing chemical and mechanical material properties. Iron base material was generally used for turbopump. This material can be categorized into stainless steel and heat resisting steel by quantity of additional elements. Each steel was also classified into austenite steel, ferrite steel, and martensite steel. Alternative materials for turbopump inducer, impeller and casing are chosen by JIS SUS 631 and 321 as a result of this study. Because the material of Russian turbopump turbine may be developed by Russia itself, alternative material can be hardly found. However, Inconel 718 for turbine material is thought to be proper in the aspect of hardness considering general use of this material for turbopump turbine in Japan and France.

• Journal of Mechanical Science and Technology
• /
• 제14권3호
• /
• pp.298-305
• /
• 2000

The functionally graded material (FGM) is the new concept for a heat resisting material. FGM consists of ceramics on one side and metal on the other. A composition and microstructure of an intermediate layer change continuously from ceramics to metal at the micron level. This study is carried out to analyze the thermal shock characteristics of functionally graded PSZ/ metal composites. Heat-resistant property was evaluated by gas burner heating test using $C_2H_2/O_2$ combustion flame. The ceramic surface was heated with burner flame and the bottom surface cooled with water flow. Also, the composition profile and the thickness of the graded layer were varied to study the thermo mechanical response. Furthermore, this study carried out the thermal stress analysis to investigate the thermal characteristics by the finite element method. Acoustic emission (AE) monitoring was performed to detect the microfracture process in a thermal shock test.

• 대한토목학회논문집
• /
• 제26권4D호
• /
• pp.587-592
• /
• 2006

Airside 지역 콘크리트 포장의 조인트에 사용되는 충진재는 항공기 이 착륙시 엔진에서 뿜어져 나오는 고열의 후폭풍과 계류장에서 항공기의 정비 및 주유시 항공유 유출에 대한 저항성을 가지고 있어야 한다. 이러한 특성 때문에 공항용 조인트 충진재는 도로포장용과는 다른 충진재의 사용이 요구되고 있다. 본 연구에서는 국내외에서 사용되고 있는 3 종류의 충진재에 대하여 물리적 특성 시험과 성능시험을 실시하였다. 시험재료는 폴리썰파이드, 폴리우레탄, 실리콘을 사용하였다. 시험결과 폴리썰파이드 충진재는 내열성과 내유성에 대한 저항성이 가장 우수하였으며, 폴리우레탄, 실리콘 충진재의 순으로 시험결과가 나타났다. Airside 지역별 특성을 고려했을 때, 폴리썰파이트 충진재는 활주로와 계류장에, 폴리우레탄 충진재는 유도로에 사용하는 것이 적절하며 실리콘 충진재는 Airside 지역 충진재로는 부적합한 것으로 나타났다.

• 비파괴검사학회지
• /
• 제27권5호
• /
• pp.417-425
• /
• 2007

보자력 측정을 통하여 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화를 평가하였다. 크리프-피로시험은 $550\;^{\circ}C$에서 각각 인장유지시간을 60초와 600초로 하여 수행 하였다. 보자력은 파단 전까지 감소하였고 경도는 파단 시까지 지속적으로 감소하였다. 크리프-피로 수명소비율이 증가함에 따라서 $M_{23}C_6$ 탄화물은 오스트왈드 성장기구를 따라서 조대화가 나타났지만 MX 탄질화물은 $550\;^{\circ}C$에서 안정하기 때문에 조대화가 나타나지 않았다. 마르텐사이트 래스 폭은 래스경계에서의 전위회복으로 인해 증가하였다. 보자력은 전위, 석출물 그리고 마르텐사이트 래스경계와 같은 미세조직적 특성에 영향을 받게 되며 이를 미세조직변화와 관련하여 이해하였다. 결과적으로, 본 연구는 페라이트기 9Cr-1Mo-V-Nb 내열강의 크리프-피로변형 동안 미세조직의 변화와 손상 정도를 보자력을 통하여 평가하는 것을 제안하였다.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.573-579
• /
• 2009

Titanium/aluminum/stainless steel(Ti/Al/STS) clad materials have received much attention due to their high specific strength and corrosion-resisting properties. However, it is difficult to fabricate these materials, because titanium oxide is easily formed on the titanium surface during heat treatment. The aim of the present study is to derive optimized cladding conditions and thereupon obtain the stable quality of Ti/Al/STS clad materials. Ti sheets were prepared with and without pre-heat treatment and Ti/Al/STS clad materials were then fabricated by cold rolling and a post-heat treatment process. Microstructure of the Ti/Al and STS/Al interfaces was observed using a Scanning Electron Microscope(SEM) and an Energy Dispersed X-ray Analyser(EDX) in order to investigate the effects of Ti pre-heat treatment on the bond properties of Ti/Al/STS clad materials. Diffusion bonding was observed at both the Ti/Al and STS/Al interfaces. The bonding force of the clad material with non-heat treated Ti was higher than that with pre-heat treated Ti before the cladding process. The bonding force decreased rapidly beyond $400^{\circ}C$, because the formed Ti oxide inhibited the joining process between Ti and Al. Bonding forces of STS/Al were lower than those of Ti/Al, because brittle $Fe_3Al$, $Al_3Fe$ intermetallic compounds were formed at the interface of STS/Al during the cladding process. In addition, delamination of the clad material with pre-heat treated Ti was observed at the Ti/Al interface after a cupping test.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.740-744
• /
• 2011

Carbon-carbon composite material is the reinforced carbon fiber. Because of its high strength, elasticity and the excellent heat-resisting property in high temperature, carbon-carbon composite material has been used in many fields such as aerospace and automotive industries, etc. Especially, aircraft brake discs used at aerospace can be cracked due to its fatigue and vibration under various loading condition. This research is focused on the influence of the vibration of carbon-carbon composite material by using accelerometer with impact hammer excitation. And the change of vibration mode will be known by applying tensile loading test.

• 대한금속재료학회지
• /
• 제48권1호
• /
• pp.28-38
• /
• 2010

High temperature high cycle and low cycle fatigue deformation behavior of automotive heat resistant aluminum alloys (A356 and A319 based) were investigated in this study. The microstructures of both alloys were composed of primary Al-Si dendrite and eutectic Si phase. However, the size and distribution for eutectic Si phase varied: a coarse and inhomogeneous distributed was observed in alloy B (A319 based). A brittle intermethallic phase of ${\alpha}-Fe\;Al_{12}(Fe,Mn)_3Si_2$ was detected only in B alloy. Alloy B exhibited high fatigue life only under a high stress amplitued condition in the high cycle fatigue results, whereas alloy A showed high fatigue life when stress was lowered. With regard to the low-cycle fatigue result ($250^{\circ}C$) showing higher fatigue life as ductility increased, alloy A demonstrated higher fatigue life under all of the strain amplitude conditions. Fractographic observations showed that large porosities and pores near the outside surface could be the main factor in the formation of fatigue cracks. In alloy B. micro-cracks were formed in both the brittle intermetallic and coarse Si phasese. These micro-cracks then coalesced together and provided a path for fatigue crack propagation. From the observation of the differences in microstructure and fractography of these two automotive alloys, the authors attempt to explain the high-temperature fatigue deformation behavior of heat resistant aluminum alloys.