In the case of a die-casting process, defects that are difficult to confirm by visual inspection, such as shrinkage bubbles, may occur due to an error in maintaining a vacuum state. Since these casting defects are discovered during post-processing operations such as heat treatment or finishing work, they cannot be taken in advance at the casting time, which can cause a large number of defects. In this study, we propose an approach that can predict the occurrence of casting defects by defect type using machine learning technology based on casting parameter data collected from equipment in the die casting process in real time. Die-casting parameter data can basically be collected through the casting equipment controller. In order to perform classification analysis for predicting defects by defect type, labeling of casting parameters must be performed. In this study, first, the defective data set is separated by performing the primary clustering based on the total defect rate obtained during the post-processing. Second, the secondary cluster analysis is performed using the defect rate by type for the separated defect data set, and the labeling task is performed by defect type using the cluster analysis result. Finally, a classification learning model is created by collecting the entire labeled data set, and a real-time monitoring system for defect prediction using LabView and Python was implemented. When a defect is predicted, notification is performed so that the operator can cope with it, such as displaying on the monitoring screen and alarm notification.
In this study, the age-hardening behavior and tensile properties of a cast AZ91-0.3Ca-0.2Y (SEN9) alloy are investigated and compared with those of a commercial AZ91 alloy. Even after homogenization heat treatment, the SEN9 alloy contains numerous undissolved secondary phases, Al8Mn4Y, Al2Y, and Al2Ca, which results in a higher hardness value than the homogenized AZ91 alloy. Under aging condition at 200 ℃, both the AZ91 and SEN9 alloys exhibit the same peak-aging time of 8 h, but the peak hardness of the latter (86.8 Hv) is higher than that of the former (83.9 Hv). The precipitation behavior of Mg17Al12 phase during aging significantly differs in the two alloys. In the AZ91 alloy, the area fraction of Mg17Al12 discontinuous precipitates (DPs) increases up to ~50% as the aging time increases. In contrast, in the SEN9 alloy, the formation and growth of DPs during aging are substantially suppressed by the Ca- or Y-containing particles, which leads to the formation of only a small amount of DPs with an area fraction of ~4% after peak aging. Moreover, the size and interparticle spacing of Mg17Al12 precipitates of the peak-aged SEN9 alloy are smaller than those of the peak-aged AZ91 alloy. The homogenized AZ91 alloy exhibits a higher tensile strength than the homogenized SEN9 alloy due to the finer grains of the former. However, the peak-aged SEN9 alloy has a higher tensile elongation than the peak-aged AZ91 alloy due to the smaller amount of brittle DPs in the former.
여름철 고온 다습한 우리나라 기온에서 토양 온도와 수분은 잔디의 생리학적 변화를 초래하며, 특히 한지형 잔디생육은 우리나라 여름철 기후의 특이성에 많은 영향을 받는다. 본 실험은 크리핑 벤트그래스(Agrostispalustris Huds.)를 이용하여 고온의 조건에서 각기 다른 토양 수분함량 조건에서의 한지형 잔디생육을 관찰하였다. 구체적인 실험 방법으로는 수분함량과 온도에 따른 bentgrass의 생육 및 생리적 스트레스 반응을 평가하였다. 모의 USGA(United State of Golf Association) 그린 조건에서의 토양 온도 및 열 특성 실험 결과 수분이 거의 없는 건조 상태에서의 토양 온도는 $34^{\circ}C$로 발열 했을 때 토양 표면 온도가 $80^{\circ}C$까지 올라가는 것을 알 수 있었다. 반면, 과수분 조건에서 $34^{\circ}C$ 발열을 했을 때에는 건조 조건에 비해 상대적으로 $10^{\circ}C$가 낮은 것을 알 수 있었다. 실험 포장에서의 온도와 수분에 따른 열 특성 변화는 관수시기와 무관하게 처리구 모두에서 관수 후에 열전도도(thermal conductivity), 열 확산성(thermal diffusivity), 및 토양 온도가 증가하였다. 이는 수분이 공기에 비해 상대적으로 높은 열전도도를 갖기 때문으로 사료된다. 또한, 본 실험에서 관수 초기에는 과수분 조건에 비해 수분 결핍 조건에서 토양 온도의 증가를 보였으며, 시간이 지남에 따라 과수분 조건에서 더 높은 토양 온도의 증가를 확인하였다. 즉, 토양 온도는 과수분 조건에서 열전도에 의해 높아져 잔디의 생육에 영향을 미친다. 이는 잔디 표면부 온도가 높은 시각대의 과도한 관수는 여름철 잔디의 생육에 부정적 영향을 미치며, 소나기 등에 의한 일시 침수 시 지반배수의 불량은 잔디 생육에 치명적인 요인이 될 수 있다는 것을 의미한다.
제주도(濟州道)와 남부(南部) 도서지방(島嶼地方)에서 한해(寒害) 및 풍해(風害)에 대한 감귤(柑橘)의 안전재배(安全栽培)와 남부지방(南部地方)에서 비닐하우스 피복(被覆)및 비닐 하우스 피복재배(被覆栽培)를 효율적(效率的)으로 수행(遂行)하기 위하여 온주밀감(溫州蜜柑)의 내한성(耐寒性) 품종(品種)의 선발(選拔), 내한성(耐寒性) 조기검정(早期檢定) 및 내한재배기술(耐寒栽培技術)에 관한 연구(硏究)를 실시한 바 결과(結果)를 다음과 같이 적요(摘要)한다. 1. 거치로 피복(被覆)한 비닐하우스에서 월동후(越冬後) 무동해개체(無凍害個體)를 내한성(耐寒性) 조기검정(早期檢定)(leaf freezing test)에 공시(供試)한 결과(結果) $-9^{\circ}C$ 저온(低溫)에 2시간(時間) 처리(處理)하여 건전개체(健全個體) 12, 약간동해개체(若干凍害個體) 15로 나타났다. 2. 비닐하우스에 거치 두겹을 피복(被覆)하고 상면(床面)에 벼짚 멀칭과 낮에 채광(採光)하는 조건에서 기온(氣溫) $-15^{\circ}C$ 내외(內外)(대전지방(大田地方))에서 하우스 내부(內部) 온도(溫度)는 $-3^{\circ}C$, 지온(地溫)은 $0^{\circ}C$ 이상(以上)으로 유지되었다. 3. 하우스내(內) 비닐 터널 설치(設置) 상면(床面) mulching은 모두 유의성있게 보온 효과를 나타냈으나, 외부 기온에 따라 다르며, 하우스내(內) 비닐 터널은 필림의 색(色)에 의한 유의차는 없었다. 4. 하우스 내부(內部)의 수직적 온도(溫度) 분포(分布)는 하우스내(內)의 온도(溫度)가 높을 때는 상부(上部)일수록 온도(溫度)가 약간 높았고 하우스 내(內)의 온도(溫度)가 낮을 때에는 중앙부(中央部) 상면(床面), 상부(床部)의 순서(順序)로 낮았다. 5. 하우스 내부(內部)의 수평적(水平的) 온도(溫度) 분포(分布)는 북면(北面)이 지온(地溫) 및 상면온도(床面溫度)가 낮고 그 밖의 동서남북(東西南北)의 가장자리 부분(部分)은 모두 낮아서 공시목(供試木)이 동해(凍害)를 받았으며 북쪽 벽면(壁面)에서 30cm내(內)의 공시목(供試木)은 동해(凍害)가 심했다. 6. 북면(北面) 바깥쪽 벽면하(壁面下)에 $30{\times}30{\times}30cm$의 짚다발 절록구(絶綠溝)의 설치(設置)는 북면(北面)의 지온(地溫) 및 상면(床面) 온도(溫度) 강하(降下)를 막아서 동해(凍害)를 막는 효과(效果)가 기대(期待)된다. 7. 흐린날, 눈 나린 날은 하우스 내외(內外)의 온도(溫度) 차이(差異)가 적었으나 방열이 적어서 내부(內部) 온도(溫度)는 야간(夜間)에도 비교적 높게 유지되었다. 8. 1일중 최고온도(最高溫度)의 peak는 하우스 내외(內外) 모두 15시(時) 전후(前後)에 있고 최저온도(最低溫度)의 peak는 모두 6시(時) 전후(前後)에 있으며 외부(外部) 온도(溫度)의 최저(最低)에 따라 내부(內部)도 변한다. 맑은 날의 최고온도(最高溫度)는 차(差)가 크고($19^{\circ}C$, 11월하순(月下旬)) 눈오는 날, 흐린 날은 차(差)가 적었으로($9^{\circ}C$, 11월하순(月下旬)) 특히 눈온 날 하우스내(內)의 온도(溫度) 강하(降下)가 적어서 야간(夜間)에 온도곡선(溫度曲線)은 평행(平行)에 가까왔다. 9. 내한성(耐寒性), 반왜성(半矮性)(semi-dwarf type), 단지형(短枝形)(spur type) 우량품종(優量品種)을 효과적(效果的)인 방한(防寒) 피복(被覆) 재배(栽培)의 기술(技術)을 적용(適用)한다면 제주도(濟州島) 및 남부지방(南部地方)에서의 감귤(柑橘)의 안전재배(安全栽培)와 재배(栽培) 면적(面積)의 확대(擴大)가 기대(期待)된다.
탁주의 저장성에 영향을 미치는 미생물의 열저항성을 측정하고 이들 미생물에 대한 상업적 살균조건을 수립하였다. 대부분의 탁주내 세균 영양세포 $60^{\circ}C$의 가열에서 파괴되었으며 생잔 포자형성균은 저장기간 중 거의 증식되지 않았다. 따라서 탁주의 저장 중 품질저하를 일으키는 미생물의 효모와 곰팡이류로 판단되었다. 정치형 cap-tube 가열에서 효모의 D-value는 $65^{\circ}C$에서 3.5분, $80^{\circ}C$에서 0.46분이었으며 곰팡이는 $65^{\circ}C$에서 2.7분. $80^{\circ}C$에서는 0.25분이었다. 그러나 연속식 coil형 열교환기를 사용할 경우 효모의 D-value는 $65^{\circ}C$에서 7.1초, $80^{\circ}C$에서 2.3초로, 곰팡이의 경우 $65^{\circ}C$에서 3초, $80^{\circ}C$에서 1초 이하로 크게 낮아졌다. 연속식 코일형 열교환기에서 $65^{\circ}C$ 이상의 온도에서 17초간 가열한 탁주는 $30^{\circ}C$에서 2주간 저장하는 동안 산도 및 pH변화를 보이지 않았으나 점도가 다소 증가하는 경향을 보였다. 효모의 살균효과 12D를 얻기 위한 가열온도가 $70^{\circ}C$에서 $85^{\circ}C$로 증가할 수록 화독냄새와 쓴 맛은 증가하였으며 따라서 탁주의 전체적인 기호도가 저하하였다. 그러나 $80^{\circ}C$에서 가열시간을 8D에서 12D로 증가시킬 경우 온도증가에서처럼 커다란 품질변화가 나타나지 않았다. 광범위한 품질평가시험결과 연속식 살균장치에서 $80^{\circ}C$에서 탁주효모의 10D에 해다하는 23초동안 가열살균하는 것이 탁주의 저온살균조건으로 가장 적합하다는 결론을 얻었다.
제강분진(EAF dust, 이하 더스트) 50wt%와 핵 형성제를 함유한 규산염계 유리 시편을 열처리하여 결정화 시킨 후 미세구조를 관찰하였다. 제조된 유리의 DTA 분석결과 결정화온도($T_c$)는 $850^{\circ}C$ 부근이었으며 이로부터 열처리 조건을 $950^{\circ}C$/15 hr로 정하였다. 핵 형성제 $TiO_2$는 $Fe_2O_3$나 $Cr_2O_3$에 비해 기계적 특성 및 화학적 내구성이 willemite 결정보다 우수한 franklinite 결정상의 성장을 시키는 효과가 탁월하였다. $TiO_2$가 첨가된 일부 결정화 유리 시편에서 augite 결정상이 관찰되었으며, 첨가량이 증가할수록 willemite 결정상은 줄어들고 franklinite 결정상은 증가하였다. 특히 5wt% 첨가된 시편은 willemite 결정상이 나타나지 않았으며 $1{\sim}2\;{\mu}m$ 크기의 franklinite 결정상이 유리 모상내에 고르게 분포되어 있었다. 또한 $TiO_2$가 5wt% 첨가된 시편에 $Fe_2O_3$를 첨가하면 franklinite 결정상들이 더욱 성장하여 서로 합체됨으로서 수지상 모양의 결정상을 나타내었다.
The ischemia-responsive 94 gene (irp94) encoding a 94 kDa endoplasmic reticulum resident protein was investigated its molecular properties associated with unfoled protein responses. First, the expression of irp94 mRNA was tested after the reperfusion of the transient forebrain ischemia induction at the central nervous system in three Mongolian gerbils. Second, irp94 expression in PC12 cells, which are derived from transplantable rat pheochromocytoma cultured in the DMEM media, was tested at transcriptional and translational levels. The half life of irp94 mRNA was also determined In PC12 cells. Last, the changes of irp94 mRNA expression were investigated by the addition of various ER stress inducible chemicals (A23187, BFA, tunicamycin, DTT and $H_2O_2$) and proteasome inhibitors, and heat shock. High level expression of irp94 mRNA was detected after 3 hours reperfusion in the both sites of the cerebral cortex and hippocampus of the gerbil brain. The main regulation of irp94 mRNA expression in PC 12 cells was determined at the transcriptional level. The half life of irp94 mRNA in PC12 cells was approximately 5 hours after the initial translation. The remarkable expression of irp94 mRNA was detected by the treatment of tunicamycin, which blocks glycosylation of newly synthesized polypeptides, and $H_2O_2$, which induces apoptosis. When PC12 cells were treated with the cytosol proteasome inhibitors such as ALLN (N-acetyl-leucyl-norleucinal) and MG 132 (methylguanidine), irp94 mRNA expression was increased. These results indicate that expression of irp94 was induced by ER stress including oxidation condition and glycosylation blocking in proteins. Expression of irp94 was increased when the cells were chased after heat shock, suggesting that irp94 may be involved in recovery rather than protection against ER stresses. In addition, irp94 expression was remarkably increased when cytosol proteasomes were inhibited by ALLN and MG 132, suggesting that irp94 plays an important role for maintaining the ERAD (endoplasmic reticulum associated degradation) function.
붕규산염계 유리에 EAF Dust를 $40{\sim}80wt%$ 첨가하고 후 용융하여 유리를 제조한 후 $700^{\circ}C$/10hr으로 열처리하여 결정화유리 시편을 합성하였다. FT-IR, SEM, 그리고 EDS 분석을 통하여 조성 및 열처리 조건에 따른 시편내 결정상 및 결합상태 변화를 관찰하고, 이를 TCLP(Toxic Characterization Leaching Procedure) 실험에서 얻은 결과와 연계시켜 시편의 화학적 내구성을 연구하였다. 유리에 더스트 첨가량이 증가함에 따라 FT-IR 스펙트럼 상의 가교산소 진동피크($1050{\sim}1060cm^{-1}$)와 비가교산소 진동피크($960cm^{-1}$)가 합쳐진 넓은 피크($1000cm^{-1}$ 부근)가 저파수쪽으로 이동하였다. 동시에 boroxol ring의 $B_2O_3$ 구조가 tetrhedral-, trigonal- 그리고 di-borate로 변화되는 것을 확인하였다. 결정화유리 시편에서 Fe-O 피크가 확인되었으며 이는 spinel이 생성되었다는 XRD 결과와 일치하였다. TCLP를 행한 유리시편의 표면은 균열이 심하였으나 결정화유리는 큰 변화가 없어, 결정상 생성이 화학적 내구성을 향상시킴을 확인하였다. Fe의 용출량은 더스트가 80wt% 첨가된 결정화유리의 경우, 유리시편에 비하여 1/15로 감소하였다. Zn은 더스트 첨가량이 70wt% 이하인 결정화유리에서 용출량이 유리에 비해 높았으나 80wt% 이상 시편에서는 유리보다 감소하였고 이는 willemite 생성과 연관이 있는 것으로 사료된다.
The microstructures and the creep rupture properties of dissimilar welds between the Ni-based superalloy Inconel 740H and the non-stabilized austenitic stainless steel TP316H have been characterized. The welds were produced by shielded metal arc (SMA) welding process with the AWS A5.11 Class ENiCrFe-3 filler metal, commonly known as Inconel 182 superalloy. Postweld heat treatment at $760^{\circ}C$ for 4 hours was conducted to form ${\gamma}^{\prime}$ strengthener in Inconel 740H. The austenitic weld metal produced by Inconel 182 had a dendritic microstructure, and grew epitaxially from the both sides of Inconel 740H and TP316H base metals. Since both Inconel 740H and TP316H did not undergo any solid-state transformation during welding process, there were no heat-affected-zone (HAZ) sub-regions and the coarsoned grains near the weld interface were limited to a narrow region. The hardness of Inconel 182 weld metal was ~220 Hv. The gradual hardness decrease was detected at HAZ of TP316H, and the TP316H base metal displayed the lowest hardness value (~180 Hv) whilst the Inconel 740H showed the highest hardness value (~400 Hv). Fracture after creep occurred at the center of weld metal, regardless of creep condition. It was found that during creep the cracks initiated and propagated along interdendritic regions and grain boundaries at which Laves particles enriched in Nb, Si and Cr were present. The appropriate design of weld metal was discussed to suppress the creep-induced cracking of the present dissimilar weld.
This study was designed to compre the tensile bond strength of 4-META containging denture base resin to Co-Cr alloys after various surface treatments. Especially the surface treatment of sandblasting the mental with aluminum oxide and treating in oxidizing solution composed of 3% aqueous sulfuric acid with 1% potassium manganate were compared. Effect of surface roughness on bonding was measured after sandblasting with 50um, 300um aluminun oxide and polishing with emery pater. Also the effects of wax and wax solvent on bonding were observed. According to the type of polymerization process, heat-cured Meta-Dent resin and autopolymerizing Meta-Fast resin were used. For some specimnens, the tensile bond strength were measured agter three pre-conditions : 1day after bonding, immersed in water at $75^{\circ}C{\pm}3^{\circ}C$ for 4weeks, under normal ambient condition for 4weeks. The following results were obtained from this study : 1. The bond strengths of resins containing 4-META were significantly higher than those of conventional denture base resins(p<0.05). 2. Autopolymerizing Meta-Fast resin had higher bond strength than heat-cured Meta-Dent, resin(p<0.05). 3. The bond strengths of Biosil and Nobilium to 4-META containging resins were not significally different(p>0.05). 4. Stable adhesion can be achieved when mechanically roughen the metal surface by snadblasting with $50{\mu}m$ aluminum oxide than treating in an oxidizing soluing with potassium manganate(p<0.05). 5. Once the metal surface is contaminated with wax, the bond srtength decreased greatly in spite of wax wash with boiling water. But the bond strength recovered significantly with the use of wax solvent 6. Meta-Dent resin had higher bond strength when roughen the metal surface with $50{\mu}m$ aluminum oxide than with $300{\mu}m$ aluminum oxide(p<0.05). In case of Meta-Fast, resin, the use of $300{\mu}m$aluminum oxide was a little advantageous of bonding, but was statistically insignificant(p>0.05).
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.