• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.77-86
• /
• 2019

The present study focuses on the effect of staggered integration factor (SIF) on Morton effect simulation results. The Morton effect is a synchronous rotordynamic instability problem caused by the temperature differential across the journal in fluid film bearings. Convection and conduction of heat in the thin film displaces the hot spot, which is the hottest circumferential position in the thin film, from -20 to 40 degrees ahead of the high spot, where the minimum film clearance is experienced. The temperature differential across the journal causes a bending moment and the corresponding thermal bow in the rotating frame acts like a distributed synchronous excitation in the fixed frame. This thermal bow may cause increased vibrations and continued growth of the synchronous orbit into a limit cycle. The SIF is developed assuming that the response of the rotor-lubricant-bearing dynamic system is much quicker than that of the bearing-journal thermal system, and it is defined as the ratio between the simulation time of the thermal system and the rotor-spinning period. The use of the SIF is unavoidable for efficient computing. The value of the SIF is chosen empirically by the software users as a value between 100 and 400. However, the effect of the SIF on Morton effect simulation results has not been investigated. This research produces simulation results with different values of SIF.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2000년도 춘계 학술대회논문집
• /
• pp.172-177
• /
• 2000

In this numerical work, three dimensional supersonic laminar flow and heat transfer of a blunt body(sphere-cone) at Mach 5 is simulated. The effects of angle of attack and the spin rate on the now and heat transfer are analysed. To solve the three dimensional compressible Wavier-Stokes equation, a finite volume method with the modified LDFSS scheme is employed for spatial discretization, and a point SGS implicit method is used for time integration. It is found that the heat transfer rate increases at the windward side and decreases at the leeward side with the angle of attack. The heat transfer rate at all surfaces slightly increases with the spin rate.

• 소성∙가공
• /
• 제10권3호
• /
• pp.206-213
• /
• 2001

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature, implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study, a series of compression tests were conducted for SAF 2507 super duplex stainless steel at various temperatures and strain rates. The accumulation of plastic work was calculated through numerical integration and converted into the elevation of temperature. Subsequent logarithmic interpolation deduced isothermal flow surfaces, which were primary input data of finite element analysis. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database. The effect of accounting deformation heat was more noticeable in high-speed forming process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.119-122
• /
• 2000

Dynamic deformation of metallic materials mostly accompanies substantial amounts of deformation heat. Since the flow stress of deformation is sensitive to temperature implication of heat due to plastic work is essential to the evaluation of constitutive relations. In this study a series of compression tests were conducted for SAF 2507 super duplex stainless steel and the accumulation of deformation heat was calculated through numerical integration method. Isothermal flow surfaces were deduced from subsequent logarithmic interpolation. Simple closed die forging process was analyzed and optimized with commercial FEM code applying both raw and calibrated material database.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.270-275
• /
• 2017

Current progress in the development of semiconductor technology in applications involving high electron mobility transistors (HEMT) and power devices is hindered by the lack of adequate ways todissipate heat generated during device operation. Concurrently, electronic devices that use gallium nitride (GaN) substrates do not perform well, because of the poor heat dissipation of the substrate. Suggested alternatives for overcoming these limitations include integration of high thermal conductivity material like diamond near the active device areas. This study will address a critical development in the art of GaN on diamond (GOD) structure by designing for ideal heat dissipation, in order to create apathway with the least thermal resistance and to improve the overall ease of integrating diamond heat spreaders into future electronic devices. This research has been carried out by means of heat transfer simulation, which has been successfully demonstrated by a finite-element method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2148-2153
• /
• 2007

The electricity conversion-efficiency of solar cell for commercial application is about 6-15%. More than 85% of the incoming solar energy is either reflected or absorbed as heat energy. Consequently, the working temperature of the photovoltaic cells increases considerably after prolonged operations and the cell's efficiency drops significantly. PV/T refers to the integration of a PV module and a solar thermal collector in a single piece of equipment. By cooling the PV module with a fluid steam like air or water, the electricity yield can be improved. At the same time, the heat pick-up by the fluid can be to support space heating or service hot-water systems. In this study, a pulsating heat pipe solar heat collector was combined with single-crystal silicon photovoltaic cell in hybrid energy-generating unit that simultaneously produced low temperature heat and heat and electricity. This experiment was investigating thermal and electrical efficiency for evaluation of a PV/T system.

• 한국가시화정보학회지
• /
• 제22권1호
• /
• pp.79-84
• /
• 2024

As microchips' degree of integration is getting higher, its cooling problem becomes important more than ever. One of the promising methods is using fractal microchannel heat sink by mimicking nature's Murray networks. However, most of the related works have been progressed only by numerical analysis. Perhaps such lack of direct experimental studies is due to the technical difficulty of the temperature and heat flux measurement in complex geometric channels. Here, we demonstrate the direct visualization of in situ temperature profile in a fractal microchannel heat sink. By using the temperature-sensitive fluorescent dye and a transparent Polydimethylsiloxane window, we can map temperature profiles in silicon-based fractal heat sinks with various fractal scale factors (a=1.5-3.5). Then, heat transfer rates and pressure drops under a fixed flow rate were estimated to optimize hydrodynamic and thermal characteristics. Through this experiment, we found out that the optimal factor is a=1.75, given that the differences in heat transfer among the devices are marginal when compared to the variances in pumping power. This work is expected to contribute to the development of high-performance, high-efficiency thermal management systems required in various industrial fields.

• Journal of Computational Design and Engineering
• /
• 제3권4호
• /
• pp.330-336
• /
• 2016

The present work is concerned with heat and mass transfer of an electrically conducting second grade MHD fluid past a semi-infinite stretching sheet with convective surface heat flux. The analysis accounts for thermophoresis and thermal radiation. A similarity transformations is used to reduce the governing equations into a dimensionless form. The local similarity equations are derived and solved using Nachtsheim-Swigert shooting iteration technique together with Runge-Kutta sixth order integration scheme. Results for various flow characteristics are presented through graphs and tables delineating the effect of various parameters characterizing the flow. Our analysis explores that the rate of heat transfer enhances with increasing the values of the surface convection parameter. Also the fluid velocity and temperature in the boundary layer region rise significantly for increasing the values of thermal radiation parameter.

• 한국추진공학회지
• /
• 제8권4호
• /
• pp.109-121
• /
• 2004

본 논문에는 열교환기로서의 재색기내부에서 발생하는 주기적 및 연속적 유동을 조사하기 위한 분산, 비선형 수학적 모델이 제시되어 있다. 일차원 유동 및 2차원 격벽 내 비정상 열교환 문제를 해결하기 위한 비 반복적 수치적분 방법이 개발되었다. 제안된 방법에 대한 검증을 위하여 회전 세라믹 매트릭스 재생기에 대한 예가 제시되었으며 재생기가 최고의 열역학적 효율을 각기 위한 최적의 회전수를 계산하였다.

• Nuclear Engineering and Technology
• /
• 제53권6호
• /
• pp.2066-2073
• /
• 2021

The use of nuclear reactors is a large studied possible solution for thermochemical water splitting cycles. Nevertheless, there are several problems that have to be solved. One of them is to increase the efficiency of the cycles. Hence, in this paper, a thermal energy optimization of a Sulfur-Iodine nuclear hydrogen production cycle was performed by means a heuristic method with the aim of minimizing the energy targets of the heat exchanger network at different minimum temperature differences. With this method, four different heat exchanger networks are proposed. A reduction of the energy requirements for cooling ranges between 58.9-59.8% and 52.6-53.3% heating, compared to the reference design with no heat exchanger network. With this reduction, the thermal efficiency of the cycle increased in about 10% in average compared to the reference efficiency. This improves the use of thermal energy of the cycle.