• Investigative Magnetic Resonance Imaging
• /
• v.23 no.3
• /
• pp.179-201
• /
• 2019

Portable low-cost magnetic resonance imaging (MRI) systems have the potential to enable "point-of-care" and timely MRI diagnosis, and to make this imaging modality available to routine scans and to people in underdeveloped countries and areas. With simplicity, no maintenance, no power consumption, and low cost, permanent magnets/magnet arrays/magnet assemblies are attractive to be used as a source of static magnetic field to realize the portability and to lower the cost for an MRI scanner. However, when taking the canonical Fourier imaging approach and using linear gradient fields, homogeneous fields are required in a scanner, resulting in the facts that either a bulky magnet/magnet array is needed, or the imaging volume is too small to image an organ if the magnet/magnet array is scaled down to a portable size. Recently, with the progress on image reconstruction based on non-linear gradient field, static field patterns without spatial linearity can be used as spatial encoding magnetic fields (SEMs) to encode MRI signals for imaging. As a result, the requirements for the homogeneity of the static field can be relaxed, which allows permanent magnets/magnet arrays with reduced sizes, reduced weight to image a bigger volume covering organs such as a head. It offers opportunities of constructing a truly portable low-cost MRI scanner. For this exciting potential application, permanent magnets/magnet arrays have attracted increased attention recently. A magnet/magnet array is strongly associated with the imaging volume of an MRI scanner, image reconstruction methods, and RF excitation and RF coils, etc. through field patterns and field homogeneity. This paper offers a review of permanent magnets and magnet arrays of different kinds, especially those that can be used for spatial encoding towards the development of a portable and low-cost MRI system. It is aimed to familiarize the readers with relevant knowledge, literature, and the latest updates of the development on permanent magnets and magnet arrays for MRI. Perspectives on and challenges of using a permanent magnet/magnet array to supply a patterned static magnetic field, which does not have spatial linearity nor high field homogeneity, for image reconstruction in a portable setup are discussed.

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.381-393
• /
• 2021

Physical, mechanical, hydraulic, and geophysical tests were applied to validate methods of inspecting the effectiveness of grouting on an agricultural reservoir dam. Data obtained from series of in situ and laboratory tests considered four stages: before grouting; during grouting; immediately after grouting; and after aging the grouting for 28 days. The results of SPT and triaxial tests, including the unit weight, compressive strength, friction angle, cohesion, and N-value, indicated the extent of ground improvement with respect to grout injection. However, they sometimes contained errors caused by ground heterogeneity. Hydraulic conductivity obtained from in situ variable head permeability testing is most suitable for identifying the effectiveness of grouting because the impermeability of the ground increased immediately after grouting. Electric resistivity surveying is useful for finding a saturated zone and a seepage pathway, and multichannel analysis of surface waves (MASW) is suitable for analyzing the effectiveness of grouting, as elastic velocity increases distinctly after grouting injection. MASW also allows calculation from the P- and S- wave velocities of dynamic properties (e.g., dynamic elastic modulus and dynamic Poisson's ratio), which can be used in the seismic design of dam structures.

• Journal of the Korea Convergence Society
• /
• v.12 no.11
• /
• pp.221-228
• /
• 2021

This study was conducted to improve the convenience of design of mobile VR devices use in a way binds smart phones. Research on traditional mobile VR devices is insufficient. So the first survey was conducted on users 100 to understand the current status and status of mobile VR devices. As a result, it was found that the satisfaction with the convenience of use was significantly lowered, and countermeasures were needed. Then, a second survey of 30 Heavy Users was conducted to find out specific usability and problems of mobile VR devices. Through this, problems, ease of use, and other opinions of mobile VR devices were found. The survey results were analyzed through the Descriptive Statistics Act, and it was found that improvement was urgent due to low satisfaction with wearing and network. In-depth interviews were conducted with the same respondents. As with the problems derived first, problems such as wearing satisfaction, excessive head weight for long-term use, and lack of content could be found. Based on the previous studies, the focus group interview consisting of 6 experts derived the ease of use evaluation element. It consists of elements that can satisfy the convenience of use of mobile VR devices for creation, wearing satisfaction, network, morphology, learning, and spatiality, and has a total of 26. Using this evaluation elements, it is intended to provide better ease of use to users who will use the mobile VR device.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.48-48
• /
• 2010

Sound quality and NVH-issues(Noise, Vibration and Harshness) of vehicles has become very important for car manufacturers. It is interpreted as among the most relevant factors regarding perceived product quality, and is important in gaining market advantage. The general sound quality of vehicles was gradually improved over the years. However, today the development cycles in the automotive industry are constantly reduced to meet the customers' demands and to react quickly to market needs. In addition, new drive and fuel concepts, tightened ecological specifications, increase of vehicle classes and increasing diversification(increasing market for niche vehicles), etc. challenge the acoustic engineers trying to develop a pleasant, adequate, harmonious passenger cabin sound. Another aspect concerns the general pressure for reducing emission and fuel consumption, which lead to vehicle weight reductions through material changes also resulting in new noise and vibration conflicts. Furthermore, in the context of alternative powertrains and engine concepts, the new objective is to detect and implement the vehicle sound, tailored to suit the auditory expectations and needs of the target group. New questions must be answered: What are appropriate sounds for hybrid or electric vehicles? How are new vehicle sounds perceived and judged? How can customer-oriented, client-specific target sounds be determined? Which sounds are needed to fulfil the driving task, and so on? Thus, advanced methods and tools are necessary which cope with the increasing complexity of NVH-problems and conflicts and at the same time which cope with the growing expectations regarding the acoustical comfort. Moreover, it is exceedingly important to have already detailed and reliable information about NVH-issues in early design phases to guarantee high quality standards. This requires the use of sophisticated simulation techniques, which allow for the virtual construction and testing of subsystems and/or the whole car in early development stages. The virtual, testing is very important especially with respect to alternative drive concepts(hybrid cars, electric cars, hydrogen fuel cell cars), where complete new NVH-problems and challenges occur which have to be adequately managed right from the beginning. In this context, it is important to mention that the challenge is that all noise contributions from different sources lead to a harmonious, well-balanced overall sound. The optimization of single sources alone does not automatically result in an ideal overall vehicle sound. The paper highlights modern and innovative NVH measurement technologies as well as presents solutions of recent NVH tasks and challenges. Furthermore, future prospects and developments in the field of automotive acoustics are considered and discussed.

• Safety and Health at Work
• /
• v.14 no.4
• /
• pp.457-466
• /
• 2023

Background: During hot environment work tasks with whole-body enclosed anti-bioaerosol suit, the combined effect of heavy sweating and exhaled hot humid air may cause the N95 medical respirator to saturate with water/sweat (i.e., water-blocking). Methods: 32 young male subjects with different body mass indexes (BMI) in whole-body protection (N95 medical respirator + one-piece protective suit + head covering + protective face screen + gloves + shoe covers) were asked to simulate waste collecting from each isolated room in a seven-story building at 27-28℃, and the weight, inhalation resistance (R_f), and aerosol penetration of the respirator before worn and after water-blocking were analyzed. Results: All subjects reported water-blocking asphyxia of the N95 respirators within 36-67 min of the task. When water-blocking occurred, the R_f and 10-200 nm total aerosol penetration (P_t) of the respirators reached up to 1270-1810 Pa and 17.3-23.3%, respectively, which were 10 and 8 times of that before wearing. The most penetration particle size of the respirators increased from 49-65 nm before worn to 115-154 nm under water-blocking condition, and the corresponding maximum size-dependent aerosol penetration increased from 2.5-3.5% to 20-27%. With the increase of BMI, the water-blocking occurrence time firstly increased then reduced, while the R_f, P_t, and absorbed water all increased significantly. Conclusions: This study reveals respirator water-blocking and its serious negative impacts on respiratory protection. When performing moderate-to-high-load tasks with whole-body protection in a hot environment, it is recommended that respirator be replaced with a new one at least every hour to avoid water-blocking asphyxia.

• Korean Journal of Radiology
• /
• v.22 no.11
• /
• pp.1886-1893
• /
• 2021

Objective: To assess the feasibility of quantitatively assessing pancreatic steatosis using magnetic resonance imaging (MRI) and its correlation with obesity and metabolic risk factors in pediatric patients. Materials and Methods: Pediatric patients (≤ 18 years) who underwent liver fat quantification MRI between January 2016 and June 2019 were retrospectively included and divided into the obesity and control groups. Pancreatic proton density fat fraction (P-PDFF) was measured as the average value for three circular regions of interest (ROIs) drawn in the pancreatic head, body, and tail. Age, weight, laboratory results, and mean liver MRI values including liver PDFF (L-PDFF), stiffness on MR elastography, and T2^* values were assessed for their correlation with P-PDFF using linear regression analysis. The associations between P-PDFF and metabolic risk factors, including obesity, hypertension, diabetes mellitus (DM), and dyslipidemia, were assessed using logistic regression analysis. Results: A total of 172 patients (male:female = 125:47; mean ± standard deviation [SD], 13.2 ± 3.1 years) were included. The mean P-PDFF was significantly higher in the obesity group than in the control group (mean ± SD, 4.2 ± 2.5% vs. 3.4 ± 2.4%; p = 0.037). L-PDFF and liver stiffness values showed no significant correlation with P-PDFF (p = 0.235 and p = 0.567, respectively). P-PDFF was significantly associated with obesity (odds ratio 1.146, 95% confidence interval 1.006-1.307, p = 0.041), but there was no significant association with hypertension, DM, and dyslipidemia. Conclusion: MRI can be used to quantitatively measure pancreatic steatosis in children. P-PDFF is significantly associated with obesity in pediatric patients.

• Clinical and Experimental Pediatrics
• /
• v.49 no.9
• /
• pp.966-971
• /
• 2006

Purpose : 'Programming' describes the process that stimulus at a critical period of development has lifelong effects. The fact that low birth weight links to the risk of elevated blood pressures in adult life is well known. This study aims to examine whether this link is evident in the newborn by investigating the relationship of the intrauterine growth indices and neonatal blood pressure(BP). Methods : We studied 127 neonates who were born at Ewha Womans' Hospital and their mothers enrolled our cohort study during pregnancy. Data on the mothers and details of the birth records were tracked and collected from medical charts. Neonatal BP was measured within 24 hours after birth. Results : Neonatal SBP was positively correlated to intrauterine growth indices; birth weight(BW)(r=0.4), head circumference(HC)(r=0.4), and birth height(r=0.3). However, an inverse relationship existed, between HC/BW ratio and neonatal SBP(r=-0.4). After adjusting for the baby's sex, maternal BP, and gestational age, neonatal SBP still associated with intrauterine growth indices. SBP was 7 mmHg higher in the highest BW group(${\geq}90percentiles$) compared to the lowest group(<10 percentiles). On the other hand, SBP was 17 mmHg lower in the highest HC/BW group(${\geq}90percentiles$) compared in the lowest group(<10 percentiles). Conclusion : This study could not find the evidence that intrauterine growth retardation affect on elevated neonatal BP. It suggests that the initiating events of BP programming may occur during postnatal growth period. To identify the critical starting period that intrauterine growth retardation leads to elevated BP, a study tracking BP changes from birth to childhood is required.

• Journal of Aquaculture
• /
• v.21 no.4
• /
• pp.309-316
• /
• 2008

Effects of the various dietary additives on growth and tolerance of abalone Haliotis discus hannai to the stresses were determined in the 16-week feeding trial. Seventy juvenile (an initial body weight of 4.2 g) abalone per container were randomly distributed into 21, 50 L plastic rectangular containers each. The six kinds of experimental diets were prepared: control (CON) with no additive, by-product of green tea (BPG), extract of figs (EF), extract of green tea (EG), commercially available product of Hearok (PH), and Haematococcus (HC). In addition, dry sea tangle (ST) was prepared to compare the efficiency of the experimental diets. Fishmeal, soybean meal and shrimp head meal were used as the protein source, and dextrin, sea tangle powder and wheat flour, and soybean oil and fish oil were used as the carbohydrate and lipid sources, respectively in the experimental diets. The experimental diets were fed to abalone once a day at a satiation level with a little leftover. The feeding trial lasted for 16 weeks. At the end of the 16-week feeding trial, abalone was exposed to the different types of stresses (air exposure, and sudden changes of rearing temperature and salinity). Survival of abalone fed the sea tangle was highest. However, weight gain of abalone fed the EF, EG and PH diets was significantly (P<0.05) higher than that of abalone fed the BPG diet or dry sea tangle. Shell length of abalone fed the all experimental diets was significantly (P<0.05) higher than that of abalone fed the dry sea tangle. Accumulated mortality of abalone fed the sea tangle was low when exposed to the different types of stresses. Also, relatively low mortality was achieved in abalone fed the HC and EF diets. In considering these results, it can be concluded that the various sources of additives is effective to improve production of abalone, and Haematococcus and extract of figs can be considered as dietary additives to improve resistance of abalone against the different types of stresses.

• Korean journal of applied entomology
• /
• v.47 no.4
• /
• pp.385-394
• /
• 2008

Larvae of Monochamus saltuarius showed normal growth and development on conifers of Pinus koraiensis, P. densiflora, Abies holophylla, Larix leptolepsis, P. bungeana, and P. rigida, respectively, but the conifers influenced significantly the body weight and the survival rate of larvae. Though the larval body weights were in a wide spectrum among treatments, growth curves of them were very similar from each other, showing continuous increase from the early larval stage to about 3 months old. The body weight was decreased slightly after the feeding period of the early 3 months. The size of larvae and adults became the largest from P. bungeana fed larvae. The mid-sized ones were from P. koraiensis, P. densiflora and A. holophylla. Small ones came from L. leptolepsis and P. rigida. The larval growth was retarded without water supply. Overall survival rates from the early stage of a larva to a fertile adult were 53.6% from P. koraiensis; 51.8%, P. densiflora; 34.7%, A. holophylla; 17.8%, P. bungeana; 16.7%, L. leptolepsis; and 12.3%, P. rigida. Adults from larvae fed the 6 species of conifers, respectively, were grown into the reproductively potent adults, which laid viable eggs. A few of overwintered larvae did not pupate and remained still as a larva until the late October of the year. Data from the field survey, the head width emerged from P. koraiensis was larger than that of L. leptolepsis. The adult emergence hole in P. koraiensis was larger also. While, the size of the emergence hole was larger in the artificially innoculated log of P. koraiensis, which was kept for a larva to be with a minimized food competition and sufficient water supply, than that of the field.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.38 no.2
• /
• pp.120-125
• /
• 2018

The study was conducted to determine effects on forage productivity, feed value, grazing intensity and livestock productivity in growing Korean native female goat grazing in native pasture. Its with average initial body weight of $14.10{\pm}3.6kg$ and an average age of 4 months were used in this study. Dry matter content of native pasture was the highest at $33.48{\pm}2.56%$ in June, and the content was significantly increased from spring to autumn (p<0.05). Crude protein was maintained between 11% and 12% on average. Nutrient content was maintained at a certain level in native pasture, but there were differences due to the different types of wild grasses produced in each season. The productivity of forage crops increased from June, but decreased after August and showed a characteristic of grassland where productivity decreased rapidly in spring and autumn. The average grazing intensity are 39 head/ha. Black goat average daily gain was 80.2g/d. The stable weight gain in grazing is that the nutrient requirement of the black goat was met by supplementing the concentrated feed during grazing. study, can be expected that the productivity of livestock can be increased through the proper feeding of supplementary feed and maintenance of grazing intensity.