• Journal of the Korean Applied Science and Technology
• /
• v.36 no.1
• /
• pp.217-225
• /
• 2019

The aim of this study was determine to effect of shaft length and physical condition on golf driving performance(head speed, distance and direction). A range of drivers with length between 44 inch, 45 inch and 46 inch limit imposed by R&A rules limited were assembled and evaluated. Club head speed and drive distance and accuracy were determined three category 27 PGA pro golfer (handicaps 0, and height $170cm{\geq}171-175{\geq}175-180cm$) who golf performance. As a results follow : Head speed was significantly difference with 44, 45 between 46inch(p<.01). Distance was significantly difference with 44 between 46inch(p<.05). And direction was significantly difference with 44, 45inch between 46inch(p<.05). Head speed according to height was general similarity among shaft length in 170cm, 171-175cm. Distance were general similarity among shaft length in 170cm, and significantly difference with 44inch between 46inch in 171-175cm(p<.01), and significantly difference with 45inch between 46inch in 176-180cm(p<.05). Direction were significantly difference with 44inch between 46inch in 170cm(p<.05), but do not significantly difference with 44inch between 46inch in 176-180cm, 176-180cm. These results show that shaft length and height can affect head speed, distance and direction.

• Smart Structures and Systems
• /
• v.30 no.2
• /
• pp.159-172
• /
• 2022

To improve the accuracy of the standard penetration test (SPT) results, smart measurement system, which considers the energy transfer ratio into the sampler (ETR_Sampler), is required. The objective of this study is to evaluate the effects of joints and rod length on the transferred energy into the sampler. The energy transfer ratios into the rod head (ETR_Head) and ETR_Sampler, and the energy ratio from the head to the sampler (ER_HS) were obtained using energy modules, which were installed at the rod head and above the SPT sampler. Linear regression analyses are conducted to correlate the ER_HS with the number of joints, rod length, and SPT N-values. In addition, the dynamic resistances are calculated using both transferred energies into the rod head and into the sampler, and are compared with the corrected cone tip resistance measured from the cone penetration test (CPT). While the ETR_Head are generally constant, but the ETR_Sampler and ER_HS gradually decrease along the depth or the number of joints, except at certain depths with high SPT N-values. Thus, the ER_HS can be estimated using the number of joints, rod length, and SPT N-values. The dynamic resistance evaluated by E_Sampler produces a better correlation with the corrected cone tip resistance than that by E_Head. This study suggests that transferred energy into the SPT sampler may be effectively used for more accurate subsurface characterization.

• Korean Journal of Ichthyology
• /
• v.5 no.1
• /
• pp.96-112
• /
• 1993

The morphological characteristics of chum salmon Oncorhynchus keta, masou salmon. Oncorhynchus masou and rainbow trout, Oncorhynchus mykiss in Korea were studied from 1989 to 1990. It was found that 13 factors of the female and 11 factors of the male in body form, number of pyloric ceaca and gill rakers has significant specific differences. There were some differences among species in the ratios of body depth, caudal peduncle depth, dorsal fin length and anal fin length to standard length (PBL), and snout length, eye diameter, upper jaw length, and cheek to head length. In the ratio of head length to fork length of the male, chum salmon showed the highest(24.7%) value and rainbow trout the lowest(21.6%). No difference was found in the female. It was proved that number of vertebrae, gill rakers, pyloric ceaca and lateral line scales were useful taxonomical characteristics of the salmon species. In particular, the ratio of eye diameter (ED) to head length (HL) appeared to be a new taxonomic criterion for the salmons in Korean waters.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.8 no.1
• /
• pp.29-38
• /
• 1978

The purpose of this study is to obtain the enshortening and elongation rate of image in orthopantomograph. The subjects were consisted of 15 dry skulls attached with radiopaque materials on each anatomical points. The length measurements were performed between two points on dry skull, and between two points on film. The results are as follows: 1. The enshortening and elongation rate between two anatomical points (1) ANS↔infraorbital foramen (left:+1.3%, right:+0.7%) (2) ANS↔maxillary tuberosity(left:-11.7%, right:-14.3%) (3) Zygomatic arch length(left:-4.8%, right:-8.9%) (4) first molar↔infraorbital foramen (left:+19.8%, right:+24%) (5) inter-infraorbital foramen length(-21.4%) (6) inter-first molar length (-31.8%) (7) inter-mental foramen length(+1.4%) (8) mental foramen↔mandible angle (left:+3.3%, right:+3.3%) (9) mental foramen↔lingula(left:+8.2%, right:+3.3%) (10) mental foramen↔condyle head(left:+5.2%, right:+4.5%) (11) mandible↔condyle head (left:+15.4%, right:+16.4%) 2. The closer the object is to the occlusal plane and the median line, the smaller it appears.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.187-190
• /
• 1999

We have developed fabrication processes that form a wide-head T-gate with a 0.2 ${\mu}{\textrm}{m}$ gate length using the combination of thickness of each PMMA layer, line doses and development times for applications in millimeter- and micro-waves monolithic integrated circuits. The three-layer resist structure (PMMA/P(MMA-MAA)/PMMA = 1800 $\AA$/5800 A/1900$\AA$), 4nC/cm and over development were used for fabrication of a wide-head T-gate by the conventional double E-beam exposure technology. The experimented results show that the cross sectional area of T-gate fabricated by the proposed method is easily enlarged without additional processes.

• Journal of the Ergonomics Society of Korea
• /
• v.16 no.3
• /
• pp.1-10
• /
• 1997

This paper is concerned with the development and evaluation of the camera calibration method for a real-time head tracking system. Tracking of head movements is important in the design of an eye-controlled human/computer interface and the area of virtual environment. We proposed a video-based head tracking system. A camera was mounted on the subject's head and it took the front view containing eight 3-dimensional reference points(passive retr0-reflecting markers) fixed at the known position(computer monitor). The reference points were captured by image processing board. These points were used to calculate the position (3-dimensional) and orientation of the camera. A suitable camera calibration method for providing accurate extrinsic camera parameters was proposed. The method has three steps. In the first step, the image center was calibrated using the method of varying focal length. In the second step, the focal length and the scale factor were calibrated from the Direct Linear Transformation (DLT) matrix obtained from the known position and orientation of the camera. In the third step, the position and orientation of the camera was calculated from the DLT matrix, using the calibrated intrinsic camera parameters. Experimental results showed that the average error of camera positions (3- dimensional) is about $0.53^{\circ}C$, the angular errors of camera orientations are less than $0.55^{\circ}C$and the data aquisition rate is about 10Hz. The results of this study can be applied to the tracking of head movements related to the eye-controlled human/computer interface and the virtual environment.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.468-475
• /
• 2007

The Steel deck a structural analysis in head plate form change the objective bridge which it sells it accomplished a detailed structural analysis from the research which it sees and Bulk-head plate it accomplished. The length rib where the fatigue crack which is considerable generally occurs, width rib connection department and the length rib side, the width rib side it compares principal stress in the object and it does to sleep. It applied the grudge element model which it describes consequently after words and a load and a boundary condition and it executed it compared a static test and principal stress. It grasped the stress conduct of the The Steel deck petal which it follows in hand weaving rib affix location and the affix location to sleep in order to analyze a same location Bulk-head the head and comparison considered. From the detailed section which is reinforced with the stress investigation result hand weaving rib of the location which is weak in structural analysis result fatigue crack of form star reinforcement details basic form and Bulk-head the form which is reinforced with the head plate compared to principal stress investigation hour it is judged at the section which separates most.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.2
• /
• pp.49-55
• /
• 1982

The purpose of this study is to classify the factors influenced on the damages of head works suffered from the storm flood occurred on July 22 1980 in both Musim and Bochong rivers and to find out an integral counter measures against the causes influenced on the disaster of head works in the engineering aspect of planning, design, construction and maintenance. In this survey, number of samples was taken 25 head Works, and the counter measures against the causes of their disasters summarized was as follows, 1. In the aspect of planning a. As the flood water level after the establishment of head works is more increased than the level before setting of head works owing to having more gentle slope of river bed between the head works than nature slope of river bed. Number of head works should be reduced for the appropriate annexation of them b. In the place where head works is established on the curved point of levee, the destruction of levee becomes severe by the strong deflective current. Therefore the setting of head works on the curved point should be kept off as long as possible and in case of unavoidable circumstances the construction method such as reinforced concrete wall or stone wall filed with concrete and anchored bank revetments should be considered. 2. In the aspect of design a. As scoring phenomena at up stream is serious around the weir Where the concentration of strong current is present in such a place, up stream apron having impermeability should be designed to resist and prevent scoring. b. As the length of apron and protected bed is too short to prevent scoring as down stream bed, the design length should be taken somewhat more than the calculated value, but in the case the calculated length becomes too long to be profitable, a device of water cushion should be considered. c. The structure of protected river bed should be improved to make stone mesh bags fixed to apron and to have vinyl mattress laid on river bed together with the improvement for increasing the stability of stone mesh bags and preventing the sucked sand from the river bed. d. As the shortage of cut-off length, especialy in case of the cutoffs conneting both shore sides of river makes the cause of destruction of embankment and weir body, the culculation of cut-off length should be taken enough length based on seepage length. 3. In the aspect of design and constructions a. The overturing destruction of weir by piping action was based on the jet water through cracks at the construction and expansion joints. therefore the expansion joint should be designed and constructed with the insertion of water proof plate and asphalt filling, and the construction joint, with concaved shape structure and steel reinforcement. b. As the wrong design and construction of the weep holes on apron will cause water piping and weir destruction, the design and construction of filter based on the rule of filter should be kept for weep holes. c. The wrong design and construction of bank revetment caused the severe destruction of levee and weir body resulting from scoring and impulse by strong current and formation of water route behind the revetment. Therefore bank revetment should be designod and constructed with stone wall filled with concrete and anchored, or reinforced concrete wall to prevent the formation of water flow route behind the wall and to resist against the scoring and impulse of strong stream. 4. In the aspect of maintenance When the damaged parts occurred at head works the authorities and farmers concerned should find and mend them as soon as possible with mutual cooperation, and on the other hand public citizen should be guided for good use of public property.

• Korean Journal of Agricultural Science
• /
• v.33 no.2
• /
• pp.159-166
• /
• 2006

Threshing loss was increased due to dropping of the threshing efficiency when the 4 row head-feed combine harvested 5 row rice to improve harvesting performance of a combine. Reasonable design criteria were examined to determine the ranges of both of feed rate and the length of threshing drum for the 4 row head-feed combine being used as a 5-row combine. Harvesting performance increased as working width or working speed increased, it resulted in 15% increase when the working width increased from 4 row to 5 row. Harvesting operations of the 4 row combine performed normally in the 4 row rice in threshing loss less than 1%, however, threshing loss increased to 2.25% in the 5 row due to poor threshing efficiency. The length of threshing drum was increased from 710 mm to 810 mm as well as the speed of crop feed chain was increased from 0.61 m/s to 0.75 m/s so as to improve the poor threshing efficiency resulted from the enlarged working width from the 4 row to the 5 row, which would decrease threshing loss less than 1%.

• The Journal of Korean Physical Therapy
• /
• v.31 no.5
• /
• pp.273-278
• /
• 2019

Purpose: The purpose of this study was to investigate the effects of three-dimensional virtual reality horse riding simulator training using a head-mounted display on gait and balance in children with cerebral palsy. Methods: Ten children with cerebral palsy were randomly assigned to the horse riding simulator (HRS) group (n=5) or the horse riding simulator with virtual reality (HRSVR) group (n=5). To evaluate balance, center of gravity (COG) sway velocity and total sway distance of each group were assessed using the Wii balance board, and gait speed and stride length of each group were assessed using a gait analysis system. Results: Intra-group comparisons between pre- and post-intervention measures revealed that there were significant changes in all gait and balance variables such as stride length, gait velocity, COG sway velocity and COG sway distance in the HRSVR group (p<0.05). In the HRS group, there were significant changes in all variables except stride length (p<0.05). In addition, inter-group comparisons showed significant differences between the two groups in stride length, gait velocity and COG sway distance except COG sway velocity (p<0.05). Conclusion: The findings of this study suggest that horse riding simulator training combined with 3D virtual reality can be a new positive therapeutic approach for improving functional performance in children with cerebral palsy.