• Journal of Korean Society of Forest Science
• /
• v.105 no.4
• /
• pp.456-462
• /
• 2016

This study was conducted to analyze the effect of forest road network on accessibility and cost reduction for forest operations before and after forest road construction by investigating harvesting operations in 5 regional Forest Services (8 management planning districts). The results showed that the accessible operation area within 500 m from forest roads or public roads increased about 3.5 times after the forest road construction. The average cost reduction was 308,000 won/km/year. According to the results, forest road had a great effect on improvement of accessibility and reduction effect of forest operation cost. Therefore, the policy for expansion of forest road should be continued for preparing of effective harvesting system.

• Korean Chemical Engineering Research
• /
• v.55 no.4
• /
• pp.530-534
• /
• 2017

Chitosan is a promising flocculant for microalgae harvesting, but its scale-up application is not economically supported yet. Low solubility of chitosan in microalgae suspension demands high dosage (as a flocculant) to destabilize the cells, and thus, increases the cost of microalgae harvesting. This study identifies efficient solvents for the chitosan, and optimizes the concentration of solvents and chitosan dose to improve the harvesting efficiency. Chitosan was dissolved in different acids, and subsequently used as a flocculant. The flocculant efficacy was measured in terms of harvesting efficiency and reduction in chemical oxygen demand (COD) of the microalgae suspension. It was found that chitosan dissolved in 0.05 M HCl showed the highest harvesting efficiency ($89{\pm}0.87%$) at only 30 mg/L of dosage. In comparison, 270 mg/L of $FeCl_3{\cdot}6H_2O$ was required to attain $86{\pm}0.083%$ of the harvesting efficiency. $H_2SO_4$ dissolved chitosan required high flocculant dose (150 mg/L) and resulted in relatively low harvesting efficiency ($77{\pm}0.11%$). It was concluded that the efficacy of chitosan is solvent dependent, and the selection of proper solvent can decrease the dosage requirement for microalgae harvesting.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.29 no.3
• /
• pp.261-266
• /
• 1984

To determine the optimum harvesting methods for high yield and quality, harvesting time were tested from 30 to 45 days after heading with five days intervals, using combine, binder and knap-sack type reaper (KSTR) in harvesting machines. Under the consideration of moisture contents of grain, operating time, grain loss, harvesting cost and quality, the optimum time of barley harvesting for mechanization was 35 to 40 days after heading. Combine and binder were recommended as the suitable machines for barley harvest in the operating efficiency and harvesting cost.

• The Journal of Fisheries Business Administration
• /
• v.46 no.2
• /
• pp.59-74
• /
• 2015

This study aims to estimate optimal harvesting production, fishing efforts, and stock levels of yellow croaker caught by the offshore Stow Net and the offshore Gill Net fisheries using the current value Hamiltonian method and the surplus production model. As analyzing processes, firstly, this study uses the Gavaris general linear model to estimate standardized fishing efforts of yellow croaker caught by the above multiple fisheries. Secondly, this study applies the Clarke Yoshimoto Pooley(CY&P) model among the various exponential growth models to estimate intrinsic growth rate(r), environmental carrying capacity(K), and catchability coefficient(q) of yellow croaker which inhabits in offshore area of Korea. Thirdly, the study determines optimal harvesting production, fishing efforts, and stock levels of yellow croaker using the current value Hamiltonian method which is including average landing price of yellow croaker, average unit cost of fishing efforts, and social discount rate based on standard of the Korean Development Institute. Finally, this study tries sensitivity analysis to understand changes in optimal harvesting production, fishing efforts, and stock levels of yellow croaker caused by changes in economic and biological parameters. As results drawn by the current value Hamiltonian model, the optimal harvesting production, fishing efforts, and stock levels of yellow croaker caught by the multiple fisheries were estimated as 19,173 ton, 101,644 horse power, and 146,144 ton respectively. In addition, as results of sensitivity analysis, firstly, if the social discount rate and the average landing price of yellow croaker continuously increase, the optimal harvesting production of yellow croaker increases at decreasing rate and then finally slightly decreases due to decreases in stock levels of yellow croaker. Secondly, if the average unit cost of fishing efforts continuously increases, the optimal fishing efforts of the multiple fisheries decreases, but the optimal stock level of yellow croaker increases. The optimal harvest starts climbing and then continuously decreases due to increases in the average unit cost. Thirdly, when the intrinsic growth rate of yellow croaker increases, the optimal harvest, fishing efforts, and stock level all continuously increase. In conclusion, this study suggests that the optimal harvesting production and fishing efforts were much less than actual harvesting production(35,279 ton) and estimated standardized fishing efforts(175,512 horse power) in 2013. This result implies that yellow croaker has been overfished due to excessive fishing efforts. Efficient management and conservative policy on stock of yellow croaker need to be urgently implemented.

• Journal of Korean Society on Water Environment
• /
• v.31 no.3
• /
• pp.328-333
• /
• 2015

In this study, Mg-Sericite was used as a flocculant to harvest freshwater microalgae, Chlorella. vulgaris. Mg-Sericite separated successfully >95% of the C. vulgaris at the following optimal parameters: Mg/Si mol ratio 1.25 to 1.50, mixing time of 20 min and settling time of 20 min. The harvesting efficiency was pH dependent. The highest harvesting efficiency ($99{\pm}0.3%$) was obtained at Mg/Si mol ratio 1.5 and pH 9 to 11. These results indicated that a biopolymer, Mg-Sericite, can be a promising flocculant due to its high efficiency, low dose requirements, short mixing and settling times. This harvesting method is helpful to lower the production cost of algae for biodiesel.

• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.367-372
• /
• 2010

Consumption of pepper, a major spice vegetable used for seasoning Kimchi, continues to increase, but cultivation is in decline due to shortage of rural labor in Korea. The 39.2% of total labor requirement for conventional pepper cultivation was available for harvesting work. Therefore conventional manual harvesting should be turned to mechanical harvesting for labor-saving, cost-reducing and easy work. Surveys on conventional pepper cultivation patterns, labor requirements for various pepper cultivation works, and farmers' opinions on the mechanization of pepper harvesting were conducted to obtain basic informations. The labor requirement for pepper harvesting was 954 h/ha out of a total labor requirement of 2,436 h/ha for pepper cultivation. Harvesting was the hardest work, and hiring workmen for harvesting was also difficult. Farmers preferred to develop a small-scale pepper harvester using agricultural tractor or cultivar. Most farmer agreed to change cultivation pattern for mechanization of pepper harvesting, but hesitated to adopt new one-time-harvesting pepper varieties.

• Journal of Biosystems Engineering
• /
• v.20 no.1
• /
• pp.22-35
• /
• 1995

Pepper is the most important horticultural plant in Korean farm. Pepper harvesting has been known to be the most difficult process in pepper cultivation so that demand for mechanization is strong. In a research to develop a pepper harvesting machine performance and capacity of the harvester should be determined based on both economical feasibility and machine design concept. In order to accomplish an economical analysis of the pepper harvester, a mathematical model for comparing manual harvesting cost to machine harvest cost was developed. Validity of the model depends on the data used in the model. Economical information for the model variables was acquired from the result of farm survey on pepper cultivation technique and economics of pepper farmer. Technical information on pepper harvester were also collected through literature review and analyzed. Based on the economical analysis and synthesis of the technical information on pepper harvesters, its performance and capacity were determined. The operating performances of the harvester such as cutting, conveying, flipping, pepper removing and post-processing (sorting) were determined. Daisy capacity of the machine was determined to be 0.41 ha. A pepper harvester with the suggested capacity was economically feasible if the price of pepper harvester, pepper recovery ratio and service life of harvester were about 6 million won, 80%, and 4 years, respectively.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.56 no.4
• /
• pp.400-403
• /
• 2011

This experiment was carried out to determine the effect of mechanization on lavor-saving in sweetpotato cultivation. The field experiment was conducted from 2005 to 2006 in Mokpo Experiment Station of the National Institute of Crop Science. In order to determine the efficiency of mechanical harvesting, different harvesting methods were compared. Mechanical harvesting method was done as follows: cutting of vines by machine, removal of plastic film mulching, and harvesting by two-row and one-row harvesting system. The result showed harvesting labor was decreased by 66.6% in two-row harvesting. The ratio of damaged sweetpotato by mechanical harvesting decreased by 49.4% in two-row and 38.4% in one-row harvesting compared to conventional method. The total labor cost was saved by 48.2% - 70.4% using mechanical method. In addition, the total income also increased by ca. 62.9% - 81.2%. Thus, it was concluded that mechanical harvesting is more efficient and economical method than conventional one.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.2
• /
• pp.191-199
• /
• 2012

Rainwater harvesting systems (RWHS), one of measures for on site rainwater management, have been promoted by laws, regulations and guidelines and have been increased. However, more evaluation of economic feasibility on RWHS is still needed due to seasonal imbalance of rainfall and little experiences and analysis on design and operation of RWHS. In this study, we investigated tank capacity of RWHS to secure economic validity considering catchment area and water demand, which is affected by building scale. Moreover, sensitivity analysis was performed to examine the effect of design factors, cost items and increase rate of water service charge on economic feasibility. The BCR (benefit cost ratio) is proportional to the increase in tank capacity. It is increased steeply in small tank capacity due to the effect of cost and, since then, gently in middle and large tank capacity. In case of 0.05 in the rate of tank volume to catchment area and 0.005 in water demand to catchment area, BCR was over one from the tank capacity of 160 $m^{3}$ taking into account of private benefits and from the tank capacity of 100 $m^{3}$ taking into account of private and public benefits. Sensitivity analysis shows that increase of water demand can improve BCR values with little cost so that it is needed to extend application of rainwater use and select a proper range of design factor. Decrease of construction and maintenance cost reduced the tank volume to secure economic validity. Finally, increase rate of water service charge had considerable impact on economic feasibility.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.77.2-77.2
• /
• 2015

Recently, metamaterials attracted much attention because of the potential applications for superlens, cloaking and high precision sensors. We developed several dielectric metamaterials for enhancing antireflection or light trapping capability in solar energy harvesting devices. Colloidal lithography and electrochemical anodization process were employed to fabricate self-assembed nano- and microscale dielectric metamaterials in a simple and cost-effective manner. We improved broadband light absorption in c-Si, a-Si, and organic semiconductor layer by employing polystyrene (PS) islands integrated Si conical-frustum arrays, resonant PS nanosphere arrays, and diffusive alumina nanowire arrays, respectively. We also demonstrated thin metal coated alumina nanowire array which is utilized as an efficient light-to-heat conversion layer of solar steam generating devices. The scalable design and adaptable fabrication route to our light management nanostructures will be promising in applications of solar energy harvesting system. On the other hands, broadband invisible cloaks, which continuously work while elastically deforming, are developed using smart metamaterials made of photonic and elastic crystals. A self-adjustable, nearly lossless, and broadband (10-12GHz) smart meatamaterials have great potentials for applications in antenna system and military stealth technology.