• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.84-89
• /
• 2011

This paper studied the carburizing of chromium molybdenum steel which the heat treatment effect of gear geometric tolerance, OPD, Runout, the surface hardness, the maximum hardness, the core hardness and the bending fatigue strength were investigated. Firstly, the deformation is observed, and the results of circularity, squareness, OPD and Runout of SCM822, SCM425, and SCM415 are obtained in order. Secondly, in order to investigate the gear hardness, the surface hardness, the maximum hardness and the core hardness of SCM822, SCM425, and SCM415 are obtained; and the surface hardness of SCM822 is about 10% higher than SCM415's, and about 3% higher than SCM425's. Thirdly, the fatigue strength of SCM822 is about 10% higher than SCM415's, and about 7% higher than SCM425's in the fatigue test results. At last, for the purpose of the minimum deformation of heat treatment, and also the improvement of fatigue strength, the best gear material is SCM822 in this test.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.1
• /
• pp.1-8
• /
• 1993

In this paper, the surface roughness influenced by Sm45C hardness in high frequency induction hardening and mechanical characteristics for the changed Hv 598 part and the unchanged hardness Hv 223 part by use of cermet and ceramic cutting tools was experimentally examined. Finally, we could be had some important results by processing surface roughness on cutting conditions such as cutting speed, feed rate, depth of cut and changes of tool nose radius. The results are summarized as follows. 1. In case of the same cutting condition, the hardness of workpiece was high and acquired the best processing surface roughness when the radius of the tool nose had 0.8 mm and feed rate was 0.04 mm/rev. 2. In case of the hardness of workpiece, though the cutting speed didn't have an effect on processing surface roughness, the less feed rate and the more processing surface roughness improved. On the other hand, the low inside the hardness of workpiece, the more cutting speed and the more feed rate increase, the processing surface of roughness improved. 3. Regardless of the hardness of workpiece, the change of the cutting depth didn't have great effect on the surface roughness. 4. On cutting the high surface hardness part with cutting tools of cermet and ceramic, it can be acquired the higher processing surface roughness because it hadn't been taken effect on cutting speed, In case of the cutting process of the low inside hardness part the two cutting tools have acquired the similar processing surface roughness.

• Journal of Technologic Dentistry
• /
• v.35 no.3
• /
• pp.209-218
• /
• 2013

Purpose: The purpose of this study was to know the availability of two photosensitizers, PD, DA, as a photosensitizer instead of CQ in UDMA dental composite resin. We want to know photopolymerization effect of UDMA unfilled resin and surface hardness of composite resin containing PD and DA were compared with those of CQ, most widely used photosensitizer for dental composite resins. Methods: The photopolymerization effect of UDMA studied by FT-IR spectroscopy increased with irradiation time and the amount of photosensitizer. Knoop hardness of experimental composite resins prepared by the addition of the photosensitizer content and irradiation time. Results: The relative photopolymerization effect of UDMA increased in the order of PD > CQ > DA. The composite resin of UDMA containing DA or PD, which shows better Knoop hardness than that containing CQ. Conclusion: PD and DA show as effective photosensizers, suitable for UDMA dental composite resin compare with a higher efficiency than CQ.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.20 no.1
• /
• pp.123-132
• /
• 2002

The literature often mentions the hardness of water in dampening solutions as possible source of problem. In most literature describes that the water hardness affects print quality. However water hardness affects not only print quality, but also emulsification of ink and dampening solution. Therefore the purpose of this study was to determine if water hardness actually affects the emulsification rate of dampening solution and ink. And this study for the factors determining the emulsion velocity, we have measured water pick-up and calculated emulsion velocity constant 'k' and activation energy.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.5
• /
• pp.64-69
• /
• 2014

This article presents machining experiments to assess the relationship between the profile accuracy and the workpiece hardness using a natural diamond tool on an ultra-precision diamond turning machine. The study is intended to secure a corner cube prism pattern for reflective film capable of high-quality outcomes. The optical performance levels and edge images of corner cubes having various hardness levels of the copper-coated layer on a carbon steel plate are analyzed. The hardness of the workpiece has a considerable effect on the profile accuracy. The higher the hardness of the workpiece, the better the profile accuracy and the worse the edge wear of the diamond tool.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.690-693
• /
• 2006

As the silence of vehicle is more important, noise reduction of tire is more required. Noise of tire is divided into structure home noise and air borne noise. Tire tread has the property such as Hardness. Pattern Noise is caused by changing of tread hardness. This property has influence on the mechanisms which are Block Impact & Stick-slip sound. In the study, we found that the effect of Hardness is related to more Stick-Slip than Impact.

• Journal of Surface Science and Engineering
• /
• v.33 no.5
• /
• pp.339-348
• /
• 2000

The study was conducted on the effect of bath composition on the surface appearance, the hardness and the crystal orientation of zinc electrodeposits from the chloride bath. (1) The hardness of the zinc electrodeposits from the chloride bath was increased by suppressing mass transfer of zinc through adding the organic additives and the chlorine ion in the electrolyte. (2) The surface whiteness of zinc deposits was decreased due to the change of the preferred orientation from (002) , (103) to (101) , (100) through increasing the organic additives and chlorine ion in the electrolyte. (3) The addition of Cu, Sn, Ni or Co in the chloride bath elevated the hardness of the zinc deposits but darkened the surface whiteness. (4) The optimum condition of the organic additives and the chlorine ion for increasing the hardness of zinc deposits and preventing dark surface ranges 0.3 m1/1 to 0.4 m1/1 and 6.5 mol/1 to 6.8mol/l respectively.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2024

This study was investigated the effect of heat treatment on the microstructure and hardness of internally hardened ductile cast iron roll. The following conclusions were obtained. Some of the graphite was decreased and a bainite was produced by heat treatment. It decreased due to the decomposition of some of the cementite precipitated in the as-cast by heat treatment, but there was no significant change when it reached a certain depth. Hardness increased due to formation of bainite by heat treatment. On the surface, the hardness decreased due to the decrease in the amount of transformation of cementite into bainite, but there was no change beyond a certain depth.

• Journal of Welding and Joining
• /
• v.30 no.2
• /
• pp.76-80
• /
• 2012

In this study, the effect of the welding current on the hardness characteristics and microstructure in the resistance spot welding of 1GPa grade cold-rolled DP steel was investigated, Also, correlation between the hardness and microstructure was discussed. In spite of the change in the welding current, the hardness distributions near weld was similar. the hardness in the HAZ and the fusion zone was higher than that of the base metal and the hardness in the fusion zone was variated with the location. Especially, the hardness of HAZ adjacent to the base metal showed maximum value, and softening zone in the base metal adjacent to HAZ was found. With the increasing of welding current, there were no difference in maximum hardness and average hardness in the fusion zone were, but the hardness of the softening zone reduced. The difference in the hardness in each location of weld due to grain size of prior austenite. The softening of the base metal occurred by tempering of the martensite.

• Journal of Korean Society on Water Environment
• /
• v.33 no.5
• /
• pp.556-562
• /
• 2017

Heavy metals in water systems are being managed on the concentration-based guidelines in Korea. However, various chemicals present in water can interact with heavy metals affecting their toxicity. Such interactions are not considered in the concentration-based guidelines. This study investigated the effect of hardness and coexisting heavy metals on heavy metal toxicity to emphasize the importance of having the effect-based guidelines together with the concentration-based guidelines in water management. The toxic effects of Cd, Zn, or mixtures of Cd and Zn were studied with Daphnia magna as a test species following the standard test method at different hardness conditions (100, 200, and $300mg\;L^{-1}$ as $CaCO_3$). The toxicities of single metal solutions and mixtures showed a decreasing trend with increasing hardness, and this can be attributed to the competition between heavy metals and cations such as calcium ions ($Ca^{2+}$) that cause hardness. The predicted toxicities of the heavy metal mixtures from the single metal toxicity deviated from the measured toxicities, and the predicted toxic effects tend to be greater than the measured toxic effects suggesting that Cd and Zn are in competition. This shows the limitations of using predicted toxic effects and the needs for further studies on mixture toxicities. Overall, this study shows that the management of heavy metals in waters needs to employ the effect-based guidelines together with the concentration-based guidelines.