• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.518-522
• /
• 2013

Cyclohexanone is important intermediate for the manufacture of caprolactam which is monomer of nylron. Cyclohexanone is generally produced by dehydrogenation reaction of cyclohexanol. In this study, highly mesoporous metal oxides such as meso-$WO_3$, meso-$TiO_2$, meso-$Fe_2O_3$, meso-CuO, meso-$SnO_2$ and meso-NiO were synthesized using mesoporous silica KIT-6 as a hard template via nano-replication method for dehydrogenation of cyclohexanol. The overall conversion of cyclohexanol followed a general order: meso-$WO_3$ >> meso-$Fe_2O_3$ > meso-$SnO_2$ > meso-$TiO_2$ > meso-NiO > meso-CuO. In particular, meso-$WO_3$ significantly showed higher activity than the other mesoporous metal oxides. Therefore, the meso-$WO_3$ has wide range of application possibilities for dehydrogenation of cyclohexanol.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.107-110
• /
• 2003

The sheet metal shearing process is normally used in the precision elements such as semi-conductor components. In precision elements, burrs usually reduce the quality of machined parts and cause interference, jamming and misalignment during assembly procedures and because of their sharpness, they can be safety hazard to personnel. Furthermore, not only burrs are hard to predict and avoid, but also deburring, the process of removing burrs, is time-consuming and costly. In order to get the burr-free parts, therefore, we developed the precise burr measuring system using the laser. Using the X-Y precious table, we used vertical measuring method. Through the laser measurement system, we gain the minute analog signal, so this signal was amplified by the electric circuit. Finally, we gained the realtime burr data using A/D converter, PC. By introducing the novel laser measuring method which employing vertical measurement mechanism, we could get fast and precious burr data. Through the experiments, the accuracy of the developed system is proved. The burr height measured during the punching process can be used for automatic deburring and in-situ aligning.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1183-1192
• /
• 1993

Since the punching time is strongly related to the productivity in sheet metal stamping, there have been a lot of efforts to obtain the optimal tool path. However, most of the conventional efforts have the basic limitations to provide the global optimal solution because of the inherent difficulties of the NP hard combinatorial optimization problem. The existing methods search the optimal tool path with limiting tool changes to the minimal number, which proves not to be a global optimal solution. In this work, the turret rotation time is also considered in addition to the bed translation time of the NCT machine, and the total punching time is minimized by the simulated annealing algorithm. Some manufacturing constraints in punching sequences such as punching priority constraint and punching accuracy constraint are incorporated automatically in optimization, while several user-interactions to edit the final tool path are usually required in commercial systems.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.91-93
• /
• 2011

This paper is presented for the performance of the Fluid Dynamic Bearing(FDB) by the groove design and the tooling condition. Recently, spindle motors which require smaller size, lower sound noise, lower vibration, and higher speed of the rotation have been placed in high value-added products including Digital Lightening Processors(DLP), Hard Disk Drives(HDD), and ODDs. The spindle motors using the sintered porous metal bearing have higher vibration and acoustic noise by dry contact and large tolerance of the bearing parts. The Fluid Dynamic Bearing (FDB) with grooves is appropriate for spindle motors adequate in regards to mechanical vibration and acoustic noise. The paper shows the performance comparisons of between sintered porous metal bearing and FDB, and each FDBs according to the tooling deviations of grooves by the Finite Element Analysis(FEA) of the mechanical field. This paper shows the methods to make the grooves, the groove's depth, and the prototype of the motor with the fluid dynamic bearing. The performance characteristics of the grooves with the FDB are verified by the experimental results.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.53.2-53.2
• /
• 2011

Ti metal has superior mechanical properties along with biocompatibility, but it still has the problem of bio-inertness thus forming weaker bond in bone/implant interface and long term clinical performance as orthopaedic and dental devices are restricted for stress shielding effect. On the other hand, despite the excellent biodegradable behavior as being an integral constituent of the natural bone, the mechanical properties of ${\beta}$-tricalcium phosphate $(Ca_3(PO_4)_2;\;{\beta}-TCP)$ ceramics are not reliable enough for post operative load bearing application in human hard tissue defect site. One reasonable approach would be to mediate the features of the two by making a composite. In this study, ${\beta}$-TCP/Ti ceramic-metal composites were fabricated by spark plasma sintering in inert atmosphere to inhibit the formation of $TiO_2$. Composites of 30 vol%, 50 vol% and 70 vol% ${\beta}$-TCP with Ti were fabricated. Detailed microstructural and phase characteristics were investigated by FE-SEM, EDS and XRD. Material properties like relative density, hardness, compressive strength, elastic modulus etc. were characterized. Cell viability and biocompatibility were investigated using the MTT assay and by examining cell proliferation behavior.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1284-1287
• /
• 2005

Peripheral pentacene region gives a significant influence on C-V characteristics of metal-oxide-pentacene capacitor structure. When the gate voltage goes toward negative, the effect of peripheral pentacene region becomes larger. Remaining gate DC bias constant and changing small signal frequency, the capacitance of peripheral pentacene changes along with frequency so that the total capacitance value also changes. The influence of peripheral pentacene region should be removed to measure accurate C-V characteristics, because it is hard to take into account the effect of the region quantitatively. After removing the influence of peripheral pentacene region, acceptor concentration, flat band voltage and depletion width of pentacene thin film are extracted from an accurate C-V curve as $1.58{\times}10^{17}cm^{-3}$, -1.54 V and 39.4 nm, respectively.

• Journal of Korea Foundry Society
• /
• v.13 no.3
• /
• pp.238-247
• /
• 1993

Microstructure, hardness and wear characteristics of $SiC_p/Al-6.5wt%Si-1.7wt%Mg$ alloy composites fabricated by the method of rheo-compocasting and hot pressing are investigated in this study. The dispersion of SiC particles in the composites is homogeneous and the hardness improves as additional amount increases. The wear amount of the matrix metal increases highly as wear rates increase, for the wear mechanism changes from adhesive wear to melt wear, and the matrix metal was coated on the surface of revolving disc and its weight increases. In the 5vol% composites, Fe is adhered on the surface of specimen by the projection of the dispersed hard SiC particles which have net-work structure and the coating layer is about $300{\mu}m$. But in the composite more than 20vol%, the wear amount of composite decreases because the SiC particles which have superior hardness, wear resistance and heat resistance properties resist wear, the abrasive wear turn out predominant wear mechanism and so the wear amount of revolving disc increases.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.3
• /
• pp.3-6
• /
• 2008

Electrolytic in-process dressing (ELID) grinding is a new technique for achieving a nanoscale surface finish on hard and brittle materials such as optical glass and ceramics. This process applies an electrochemical dressing on the metal-bonded diamond wheels to ensure constant protrusion of sharp cutting grits throughout the grinding cycle. In conventional ELID grinding, a constant source of pulsed DC power is supplied to the ELID cell, but a feedback mechanism is necessary to control the dressing power and obtain better performance. In this study, we propose a new closed-loop wheel dressing technique for grinding wheel truing that addresses the efficient correction of eccentric wheel rotation and the nonuniformity in the grinding wheel profile. The technique relies on an iterative control algorithm for the ELID power supply. An inductive sensor is used to measure the wheel profile based on the gap between the sensor head and wheel edge, and this is used as the feedback signal to control the pulse width of the power supply. We discuss the detailed mathematical design of the control algorithm and provide simulation results that were confirmed experimentally.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.3
• /
• pp.242-254
• /
• 2000

This paper describes an efficient solid modeling method for thin-walled plastic or sheet metal parts, based on the non-manifold offsetting operations. Since the previous methods for modeling and converting a sheet into a solid have adopted the boundary representations for solid object as their topological framework, it is difficult to represent the exact adjacency relationship between topological entities of a sheet model and a mixture of wireframe and sheet models that can appear in the meantime of modeling procedure, and it is hard to implement topological operations for sheet modeling and transformation of a sheet into a solid. To solve these problems, we introduce a non-manifold B-rep and propose a sheet conversion method based on a non-manifold offset algorithm. Because the non-manifold offset aigorithm based on mathematical definitions results in an offset solid with tubular and spherical thickness-faces we modify it to generate the ruled or planar thickness-faces that are mostly shown in actual plastic or sheet metal parts. In addition, in order to accelerate the Boolean operations used the offset algorithm, we also develope an efficient face-face intersection algorithm using topological adjacency information.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.232.2-232.2
• /
• 2014

Since its discovery in 2004, graphene, a sp2-hybridized 2-Dimension carbon material, has drawn enormous attention. A variety of approaches have been attempted, such as epitaxial growth from silicon carbide, chemical reduction of graphene oxide and CVD. Among these approaches, the CVD process takes great attention due to its guarantee of high quality and large scale with high yield on various transition metals. After synthesis of graphene on metal substrate, the subsequent transfer process is needed to transfer graphene onto various target substrates, such as bubbling transfer, renewable epoxy transfer and wet etching transfer. However, those transfer processes are hard to control and inevitably induce defects to graphene film. Especially for wet etching transfer, the metal substrate is totally etched away, which is horrendous resources wasting, time consuming, and unsuitable for industry production. Thus, our group develops one-step process to directly grow graphene on glass substrate in plasma enhanced chemical vapor deposition (PECVD). Copper foil is used as catalyst to enhance the growth of graphene, as well as a temperature shield to provide relatively low temperature to glass substrate. The effect of growth time is reported that longer growth time will provide lower sheet resistance and higher VSG flakes. The VSG with conductivity of $800{\Omega}/sq$ and thickness of 270 nm grown on glass substrate can be obtained under 12 min growing time. The morphology is clearly showed by SEM image and Raman spectra that VSG film is composed of base layer of amorphous carbon and vertically arranged graphene flakes.