• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.157-160
• /
• 2005

The surface energies and acid-base interaction between the untreated and treated Jute or Hemp fibers and different matrix compositions of polypropylene-maleic anhydride polypropylene copolymers (PP-MAPP) were investigated using dynamic contact angle measurement. The contribution of the acid-base property into the interfacial adhesion of the natural fibers/matrix systems were characterized by calculating the work adhesion coming from the acid-base interaction. On the other hand, microfailure mechanism of both single Jute and Hemp fiber bundles were investigated using the combination of single fiber tensile test and acoustic emission. Distinctly different micro failure modes of the different natural fiber/polypropylene systems wet ε observed using optical microscope and determined indirectly by AE and their FFT analysis.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.3
• /
• pp.363-371
• /
• 2003

This study is mainly concerned with phenomenon of cavitation-erosion on the several materials and corrosive liquids which were applied with vibrator(suggested by ASTM G 32, 20KHz, 50$mu extrm{m}$). The maximum erosion rate by cavitation erosion in both of distilled water and sea water appeared to be proportioned to their hardness and tensile strength. Cavitation weight loss and rate of cast iron in sea water condition were greater(approximately 3 times) than that in distilled water condition, however in case of stainless steel and brass the cavitation weight loss of composite materials were not so different in both of their conditions. Cavitation weight loss of composite materials were shown as below on this test, Duratough DL : Weight loss in sea-water condition were greater (approximately 2.3 times) than it's distilled water condition. The main tendency of cavitation erosion for metals appeared that small damaged holes causing by cavitation erosion was observed with radial pattern. On the other hand, the tendency for composites appeared that small damaged holes were observed randomly.

• Fashion & Textile Research Journal
• /
• v.13 no.6
• /
• pp.990-995
• /
• 2011

This study analyzed the effects of the knit stitch type, fiber composition, and yarn thickness on the mechanical properties of knitted fabric. The results were as follows: The course density was the highest in the case of the rib stitch. On the other hand, the wale density was the highest in the case of the float stitch. The thickness was the highest in the case of the rib stitch. The same results were obtained even for different fiber compositions and yarn thicknesses considered in this study. The burst strength of wool knit fabric was higher than that of A/W knit fabric. The stiffness was the lowest in the case of the plain stitch. The same results were obtained even for different fiber compositions and yarn thicknesses. The pilling properties were excellent for all knit stitches, fiber composition, and yarn thicknesses as pilling degree : 5. The air permeability decreased in the following order : rib > plain > float stitch. The same results were obtained even for different fiber compositions and yarn thicknesses. The heat retention rate decreased in the following order : rib > float > plain stitch. The same results were obtained even for different fiber compositions and yarn thicknesses.

• Journal of Oriental Neuropsychiatry
• /
• v.26 no.3
• /
• pp.211-224
• /
• 2015

Objectives: This study aimed to investigate gender differences in the Korean Medical Community. Methods: Participants in the research study included 90 students regularly attending the fourth grade in Korean Medicine College, of which 48 were male and 42 were female. Results: 1. Patient's preferences for female KMD (Korean Medicine Doctor) had the lowest response rate in Korean Medical Society. Preferences for male KMD were due to factors including comfort level, rationality, good training, and patient's preference. 2. Patient's preferences for female KMD had the highest response rate in Gynecology, and Pediatrics. On the other hand, patient's preferences for female KMD had the lowest response rate in the other 7 specialty subjects. 3. The reasons for gender discrimination against male KMD were lack of subtlety, lack of empathy, authoritative attitude, and lack of patient management skills. The reasons for gender discrimination, against female KMD were childcare burden, social prejudices, lack of physical strength, and housekeeping burdens. Conclusions: The study results indicated that there was a lower preference for female KMD than male KMD among the Korean Medical Society and in patients' consciousness. Male-centered culture of Korean Medical Society had no role in this finding, but masculine image for KMD jobs and work-family double burden for female KMD were important contributing factors.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.960-968
• /
• 2003

The objective of this study is to investigate the effect of AE activities in the crack opening and closure during the fatigue test. The laboratory experiments for various materials and test conditions were carrie out to identify AE characteristics of fatigue crack propagation. Compact tension specimens of SWS 490B and Al 7075-T6 alloy were prepared for fatigue test. AE activities were analyzed based on the phase of the loading cycle. In case of SWS 490B, the most of AE was generated when the crack began opening and the crack closed fully, whereas a few in the full opening of the crack. On the other hand, in case of Al 7075-T6, a distinct AE activity was observed during crack opening process. AE activity in the peak loading of cycle was different with each specimen. However, in the same material, AE activity was not affected by the change of cyclic frequency (0.1, 0.2, 1.0 ㎐). It was found that AE activities during crack opening and closure depend on material properties such as micro-structure, yield strength and elongation.

• Advances in concrete construction
• /
• v.6 no.1
• /
• pp.69-85
• /
• 2018

In order to provide sufficient stability and resistance against bleeding and segregation during transportation and placing, mineral admixtures are often used in self-compacting concrete mixes (SCC). These fine materials also contribute to reducing the construction cost and the consumption of natural resources. Many studies have confirmed the benefits of these mineral admixtures on properties of SCC in standard curing conditions. However, there are few published reports regarding their effects at elevated curing temperatures. The main objective of this study is to investigate the effect of three different mineral admixtures namely limestone powder (LP), granulated blast furnace slag (GS) and natural pozzolana (PZ) on mechanical properties and porosity of SCC when exposed to different curing temperatures (20, 40, 60 and $80^{\circ}C$). The level of substitution of cement by mineral admixture was fixed at 15%. The results showed that increasing curing temperature causes an improvement in performance at an early age without penalizing its long-term properties. However the temperature of $40^{\circ}C$ is considered the optimal curing temperature to make economical and high performance SCC. On the other hand, GS is the most suitable mineral admixture for SCC under elevated curing temperature.

• Corrosion Science and Technology
• /
• v.11 no.5
• /
• pp.184-190
• /
• 2012

Cu alloy is widely used for marine applications due to its excellent ductility and high resistance for corrosion as wells as cavitation. However, long term exposure of the material to marine environments may result in damages caused by cavitation and corrosion. Water cavitation peening has been introduced in order to improve resistance of Cu alloy to corrosion and cavitation. The technology induces compressive residual stress onto the surface, and thus enhances the fatigue strength and life. In this study, the characteristics of the material were investigated by using water cavitaiton peening technique, and results showed that 2 minutes of water cavitation peening indicated the considerable improvement in hardness. On the other hand, over 10 minutes of water cavitation peening accelerated damages to the surface. In the case of ALBC3, water cavitation peening in the range of 2 to 10 minutes has shown the excellent durability and corrosion resistance while minimizing surface damages.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.221-228
• /
• 2003

The stress corrosion index of Kumamoto andesite are evaluated by two types of testing method. One is the uniaxial compression test under various water vapor pressures, and the other is the double torsion (DT) test under a constant water vapor pressure. For the uniaxial compression tests, the uniaxial compressive strength increases linearly with decreasing water vapor pressure on the double logarithmic coordinates. As the results, the stress corrosion index obtained is estimated 44. On the other hand, in the DT test, the relaxation (RLX) test and the constant displacement rate (CDR) test were conducted. For the CDR test, as the displacement rate of loading point increases, the crack velocity increases. However, the fracture toughness is constant regardless of the change in displacement rate and the average fracture toughness is evaluated $2.07MN/m^{3/2}$. For the RLX test, the crack velocity-stress intensity factor curves are smooth and linear. The stress corrosion index estimated from the curves is 37. Comparing stress corrosion indexes in the uniaxial compression test and the DT test, there is no significant difference in these values, and they are considered to be in coincident each other regardless of testing methods. Therefore, it is concluded that stress corrosion is one of material constants of rock.

• Toxicological Research
• /
• v.20 no.1
• /
• pp.21-29
• /
• 2004

We used cDNA microarray to assess gene expression profiles in hematopoetic cell line, U-937, exposed to low doses of ionizing irradiation. The 1,000 DNA elements on this array were PCR-amplified cDNAs selected from named human cancer related genes. According to the strength of irradiation, the levels of some gene expression were increased or decreased as dose-dependent manner. The gene expressions of Tubulin alpha, protein kinase, interferon-alpha, -beta, -omega receptor and ras homolog gene family H were significantly increased. Especially, Tubulin gene was shown 2.5 fold up-regulated manner under stress of 500 rad irradiation than 200 rad. On the other hand, fibroblast growth factor 12 and four and a half LIM domains, etc. were significantly down-regu-lated. Also, tumor protein 53(TP53) related genes that p53 inducible protein, tumor protein 53-binding protein looks of little significance as radiation sensitive manner. The radio-sensitivity of tubulin gene etc. that we proposed could be useful to rapid and correct survey for the bio-damage by exposure to low dose irradiation.

• Transactions of Materials Processing
• /
• v.18 no.8
• /
• pp.640-645
• /
• 2009

Recently, boss and rib test based on backward extrusion process was proposed to quantitatively evaluate the interfacial friction condition in bulk forming process. In this test, the tube-shaped punch with hole pressurizes the workpiece so that the boss and rib are formed along the hole and outer surface of the punch. It was experimentally and numerically revealed that the height of boss is higher than that of the rib under the severe friction condition. This work is focused on the effect of the punch design and flow stress on deformation pattern in boss and rib test. From the boss and rib test simulations, it was found that there is slight variation in both the heights of boss and rib according to the length of punch land, nose radius, and face angle. However the hole diameter of the punch and the clearance between the punch and die have a significant influence on the calibration curves showing the heights of the boss and rib. In addition, the effect of flow stress on the calibration curves was investigated through FE simulations. It was found that there is no effect of strength coefficient of the workpiece on the calibration curves for estimation of friction condition. On the other hand, the strain-hardening exponent of the workpiece has a significant influence on the calibration curve.