• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.40-46
• /
• 2010

To protect press operator from the after-reach hazard, current Ministry of Labor Notification(MOLN) requires the use of a formula for calculating the safe distance away from the point of operation for locating press protective devices, Two Hand Control Devices(THCD) and Active Opto-Electronic Protective Devices(AOPD), on a power press. This formula is based on a same hand speed constant of 160cm/s. While EN standards use different hand speed constant for THCD and AOPD respectively. The objective of this study is to compare two guidelines on the hand speed constant published by MOLN and EN 692, also to propose a proper hand speed constant and validate it experimentally. As a experimental result, it could be known that hand speed constant of Ministry of Labor Notification should be improved as that of EN standards.

• Journal of Wind Energy
• /
• v.3 no.2
• /
• pp.34-41
• /
• 2012

The paper is focusing on investigating the control characteristics of the baseline controller of 5 MW wind turbine provided by NREL(National Renewable Energy Laboratory). The baseline controller consist of two control logics, a maximum power tracking control below the rated wind speed and a constant power control above the rated wind speed. In the low wind speed, the mean generator power for changing the turbulent intensity and the optimal constant is studied through numerical simulations using FAST program. On the other hand, the constant power control logic and the constant control logic are compared in the high wind speed. It is confirmed that optimal constant is closely related to the turbulent intensity in low wind speed region and the constant torque control has better performance than the constant power control with respect to mechanical load in high wind speed region.

• Tribology and Lubricants
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2003

Recently, PM-high speed steel(PM-HSS) has reportedly been a good alternative material for rolling mill because of its superior performance to conventional HSS. This paper has been aimed to investigate the possibility for application to rolling contact element for PM-HSS by X-ray diffraction technique. The X-ray elastic constant for PH-HSS has been found by X-ray diffraction during the four-point bending test. Residual stress and half-value breadth on the contact surface during rolling contact fatigue process by X-ray diffraction have also been measured. The result of this study shows that the application of X-ray diffraction technique to PM-HSS could be as possible alternative material as conventional HSS. Half-value breadth on rolling contact surface by X-ray diffraction is not changed during rolling contact fatigue process. On the other hand, the residual stress is changed. This suggests that dislocation reaction has been hardly occurred in rolling contact, depending on super-saturated carbon in PM-HSS.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.7
• /
• pp.792-798
• /
• 2013

In this study, we have carried out measurement for exhaust emissions such as particulate matter (PM), nitrogen oxide and carbon oxide from main engines installed on the training ships, HANBADA and HANNARA, of Korea Maritime University. In particular, we considered the two conditions; at arrivals/departures and at constant speed of about 160 rpm. The result showed that the concentration of PM at the ship arrival was 2.41mg/m3. On the other hand, when the ship is on the navigation condition, the concentration of PM was 1.34 mg/m3. The concentrations of nitrogen oxide and carbon oxide were measured in the range of 1,120~1,600 ppm and 320~1,450 ppm at the arrival and departure at the port. Under constant speed condition, the concentrations of nitrogen oxide and carbon oxide were 913~1,470 ppm and 73~460 ppm, respectively. Generally, the concentrations of exhaust emissions under the arrivals and departures were higher than that of constant speed condition. These results imply that the ship operation skill to prevent a sudden load change of main engine is needed during the arrival or departure. In addition, it means that the difference of exhaust emissions according to navigation conditions has to be considered when the reduction technologies of air pollutants from ships are developed.

• The Korean Journal of Rheology
• /
• v.11 no.2
• /
• pp.67-72
• /
• 1999

A magneto-rheological(MR) fluid based rotary loading and braking device is developed. The loading and braking forces of the device are accurately adjustable by controlling the yield stress of MR fluid, so that the vibration control, the precision position control and the speed control of rotating machines equipped with the device can be achieved. As an engineering application, constant rotational speed regulation is conducted using the device manufactured in laboratory, introducing PI control action not only with varying torque due to gravitation, with initial angular speed, but also with constant external torque made by hand. To do this, first, mathematical model was obtained via experiments. And then, simulation was carried out, based on the experimentally identified model. Its result was confirmed through experiment. It is identified by simulation and experimental results that PI action leads to satisfactory control performance in both cases that varying torque due to gravitation, with initial angular speed, and constant external torque are applied.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.34 no.3
• /
• pp.294-301
• /
• 1998

Towing performance of a midwater trawl system was examined aboard the training ship KAYA(2900ps) at the East Sea using the midwater trawl gear that had been designed and manufactured in accordance with the vessel. In this experiment, the trawl system data, the towing speed, the length and tension of the warp, net mouth height, and the depth of otter boards and net were measured and analyzed. The results are as follows: 1. In case of heaving in the warp with constant towing speed, the tension was suddenly increased and then again was reduced and after returned to the original steady state tension. At this time, net height was reduced a bit by ascension of ground rope, but returned to it’s original value. In the case where the warp was paid out, the tension was suddenly decreased and after increased and then returned to the tension of the original state, and the net height was greatly increased instantly by the sinking of the ground rope and then returned to the steady state 2. In the case of increased towing speed mm constant warp length, the tension was increased, and reducing the net height, the gear depth was decreased. On the other hand, in the case where towing speed was reduced, the tension was reduced and the gear depth and net height was increased. 3. Otter boards show a swing motion in the scope of 5~ 10m continuously. Otter boards responded to the state change of the trawl system at first, and then the motion of the net appeared. 4. The depth of net center was about 20m deeper than that of the otter boards, it shows about 0.4 times the warp length at the 4knots towing speed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.19-20
• /
• 2006

The emission of particulate matter from marine diesel engines is already restricted by regional regulations in some countries, and IMO has been preparing the regulation for particulate matter from 53rd MEPC. But confusingly, the gravimetric PM measurement methods and procedures are not established clearly yet. On the other hand, smoke measurement method is set clearly, and it can also indicate PM, though it is not direct gravimetric method. As the preparing step for regulations about PM, we measured the smote density of exhaust emission from the marine four-stroke diesel engines operated in constant speed and various load steps on the test-bed, using the filter-type smoke measuring instrument. As a result, we understood the omission characteristics of smoke from the engines. Additionally, to obtain the objective reliability of our measurement data, we carried out experimental studies about various measuring parameters that could affect the smoke density.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.539-544
• /
• 1997

Although the identification of a moving noise source is important in reducing the source power of the transport systems such as airplane or high speed train, the direct measurement of the frequency characteristics is usually difficult due to wind noise when using a microphone running with that noise source. On the other hand the motion of a source causes the frequency characteristics of the pass-by sound measured at a fixed point to be distorted that it is quite difficult to identify the original source characteristics. In this study the relationship between the spectra of the source and the pass-by sound signal is analyzed for a source moving at a constant velocity. The effects of the speed and the frequency characteristics of the source on the pass-by noise spectrum are investigated through numerical simulations.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.44-49
• /
• 2000

Recently, PM-high speed steel(PM-HSS) has reportedly been a good alternative material for rolling mill because of its superior peformance to conventional HSS. This paper has been aimed to investigate the possibility for application to rolling contact element for PM-HSS by X-ray diffraction technique. The X-ray elastic constant for PM-HSS has been found by X-ray diffraction during the four-point bending test. Residual stress and half-value breadth on the contact surface during rolling contact fatigue process by X-ray diffraction have also been measured. The result of this study shows that the application of X-ray diffraction technique to PM-HSS could be as possible alternative material as conventional HSS. Half-value breadth on rolling contact surface by X-ray diffraction is not changed during rolling contact fatigue process. On the other hand, the residual stress is changed. This suggests that dislocation reaction has been hardly occurred in rolling contact, depending on supersaturated carbon in PM-HSS.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.4
• /
• pp.16-21
• /
• 2013

This paper presents a DC link voltage control method to reduce the ripple current and the switching loss in the sinusoidal current drive system for the wide-speed range PMSM. The DC link voltage of the three phase inverter in the sinusoidal current drive system is designed by the back-EMF voltage at maximum speed of the PMSM. In general, the drive systems have used the constant DC link voltage without reference to the motor speed. The current ripple causes hysteresis loss and makes noise. In addition, the switching loss on the inverter increases in proportion to the rise in the DC link voltage. In this paper, we propose the variable DC link voltage control method to reduce the current ripple in the PMSM drive system. We show reduction effect of the current repple and the switching loss through simulation results.