• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.809-815
• /
• 1996

When Li2O.2SiO2 glass was crystallized between the temperature of maximum nucleation and the temperature of maximum crystal growth it was found that the control of heating rate had serious effect on the crystallinity and microstructure and the greatly changed physical properties. Density and elastic modulus tends to increase but thermal expansion coefficient decreased with increased crystallinity. When heating rate between the tempe-rature of maximum nucleation and the temperature of maximum crystal growth was 10~5$0^{\circ}C$/hr. crystallinity was increased to result in the increment of strength. When nuclation was done at 44$0^{\circ}C$ for 5 hours and the temperature of crystal growth was held at 575$^{\circ}C$ strength was increased until crystallinity reached 65% and strength was decreased with higher crystallinity. These phenomena could be explained that even for the same crystallinity different heat rates resulted in different number and size of cracks.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.4 s.33
• /
• pp.515-521
• /
• 1997

The effects of heat treatment and fiber orientation on tensile strength and fatigue behavior were studied in a continuously reinforced. magnesium-based composite Following an earlier TEM investigation, specimens were thermally aged to modified the interfacial zone between the alumina fibers and the magnesium alloy matrix. From the tensile experimental results, the ultimate tensile strength of the aged specimens were lower than that of the as-fabricated due to weak fiber-matrix interfacial strength with chemical reaction during the thermal processing. The fatigue crack growth experiments were conducted with specimens having the fiber orientation normal to the crack growth direction (longitudinal) and also specimens with the fibers oriented parallel to the crack growth direction(transverse). A comparison of the fatigue crack growth behavior indicates that aged longitudinal specimens are more resistant to fatigue crack growth the as-fabricated longitudinal specimens. Conversely, as-fabricated transverse specimens are more resistant to fatigue crack growth than aged transverse specimens.

• Journal of the Korean Ceramic Society
• /
• v.21 no.1
• /
• pp.27-32
• /
• 1984

During the last decade there have been many studies on the new ceramics especially engineering ceramics. Sintered silicon carbide is one of the main materials in engineering ceramics. This study shows the effects of surface treatment and microstructure especially the abnormal grain growth on the strength of sintered SiC. Surface of sintered SiC and treated with 400, 800 and 1200 grit diamond wheel. Grain growth is introduced by increasing the sintering times at 205$0^{\circ}C$. The $\beta$longrightarrow$\alpha$ transformation occurs during the sintering of $\beta$-starting materials and is often accompanied by abnormal grain growth. The overall strength distribution are estimated using the Weibull statistics. The results show that the strength of sintered SiC is limited by extrinsic surface flaws in normal-sintered specimens. And it is sound that the finer the surface finishing and the grain size the higher the strength results. But the strength of abnormal sintering specimens is limited by the abnormally-grown large tabular grains. The Weibull modulus increases with the decreasing grain size and the decreasing grit size of grinding.

• Korean Journal of Plant Tissue Culture
• /
• v.28 no.6
• /
• pp.341-346
• /
• 2001

To investigate the effects of MS medium strength and nitrogen concentration on bulblet formation from bulblet scale segment culture and bulblet growth from bulblet of Lilium oriental hybrid 'Casa Blanca', asiatic hybrid 'Mona', and longiflorum hybrid 'Hinomoto', 0.5∼2.0 strength of MS salts and 30∼120 mM nitrogen concentrations of MS medium were examined in vitro. The number of bulblets from bulb scale segment was favored in the strength of 0.5∼1.0 strength of MS salts or 30 mM total nitrogen concentration of MS medium in three cultivars. But the growth of bulblets formed in vitro was promoted in the 2 strength of MS medium or hight concentration of total nitrogen of MS medium up to 120 mM in three experimented cultivars.

• Advances in concrete construction
• /
• v.1 no.4
• /
• pp.341-358
• /
• 2013

Due to fast growth in urbanisation, a highly developed infrastructure is essential for economic growth and prosperity. One of the major problems is to preserve, maintain, and retrofit these structures. To meet the requirements of construction industry, the basic information on all the mechanical properties of various concretes is essential. This paper presents the details of development of various concretes, namely, normal strength concrete (around 50 MPa), high strength concrete (around 85 MPa) and ultra high strength concrete (UHSC) (around 120 MPa) including their mechanical properties. The various mechanical properties such as compressive strength, split tensile strength, modulus of elasticity, fracture energy and tensile stress vs crack width have been obtained from the respective test results. It is observed from the studies that a higher value of compressive strength, split tensile strength and fracture energy is achieved in the case of UHSC, which can be attributed to the contribution at different scales viz., at the meso scale due to the fibers and at the micro scale due to the close packing of grains which is on account of good grading of the particles. Micro structure of UHSC mix has been examined for various magnifications to identify the pores if any present in the mix. Brief note on characteristic length and brittleness number has been given.

• Advances in concrete construction
• /
• v.16 no.5
• /
• pp.255-267
• /
• 2023

The production of ultra-early-strength concrete (UESC) traditionally involves complexity or necessitates high-temperature curing conditions. However, this study aimed to achieve ultra-early-strength performance solely through room-temperature curing. Experimental results demonstrate that under room-temperature (28℃) curing conditions, the concrete attained compressive strengths of 20 MPa at 4 hours and 69.6 MPa at 24 hours. Additionally, it exhibited a flexural strength of 7.5 MPa after 24 hours. In contrast, conventional concrete typically reaches around 20.6 MPa (3,000 psi) after approximately 28 days, highlighting the rapid strength development of the UESC. This swift attainment of compressive strength represents a significant advancement for engineering purposes. Small amounts of steel fibers (0.5% and 1% by volume, respectively) were added to address potential concrete cracking due to early hydration heat and enhance mechanical properties. This allowed observation of the effects of different volume contents on ultra-early-strength fiber-reinforced concrete (UESFRC). Furthermore, the compressive strength of 0.5% and 1% UESFRC increased by 16.3% and 31.3%, respectively, while the flexural strength increased by 37.1% and 47.9%. Moreover, toughness increased by 58.2 and 69.7 times, respectively. These findings offer an effective solution for future emergency applications in public works.

• Journal of International Academy of Physical Therapy Research
• /
• v.1 no.2
• /
• pp.149-154
• /
• 2010

The purpose of this study was to investigate the effects of swiss ball exercise and taping therapy on back muscle strength on normal college students. The aim of this study was to find effective method for back muscle strengthening. Subjects of 30 college students divided 3 groups(taping therapy group: 10, swiss ball group: 10, control group: 10). All subjects inquired physical conditions and normal exercise habits for data base. Back muscle strength measured before and after 3 weeks intervention. Taping therapy was displayed stable a growth curve in continuative a growth graph of back muscle strength better than swiss ball exercise, because it was taping therapy by periodic effect. The result of this study known to effective either taping therapy or swiss ball exercise, but both taping therapy and swiss ball exercise were effect to increase in back muscle strength.

• Journal of Biomedical Engineering Research
• /
• v.41 no.1
• /
• pp.1-7
• /
• 2020

Polyvinyl alcohol (PVA)/gelatin hydrogels were prepared by repeating freezing/thawing three times to evaluate the influence of PVA concentration on the strength and the cell growth behavior of the PVA/gelatin hydrogels. The swelling rate of the PVA/gelatin hydrogels decreased with raising the PVA content from 6 wt% to 12 wt% due to the formation of 3-D network inside the hydrogel. No appreciable degradation of the hydrogels was detected. As the PVA content increased from 6 wt% to 12 wt%, the strength of the PVA/gelatin hydrogels increased drastically from 6.4±0.9 kPa to 46.6±9.0 kPa. The PVA/gelatin hydrogels did not show any evidence of causing cell lysis or toxicity, implying that the hydrogels are clinically safe and effective. Although the strength increased with increasing the PVA content, the PVA/gelatin hydrogels containing 8 wt% exhibited the fastest cell growth, which is highly suitable for wound dressing requiring fast healing regeneration.

• Korean Journal of Metals and Materials
• /
• v.50 no.4
• /
• pp.271-279
• /
• 2012

9-12% Cr steels have been used in thermal power plants which repeat start and stop operations. Major factors of fatigue life are temperature, frequency, stress ratio, holding time, microstructure, and environment. Normally, fatigue life decreases at high temperature, low frequency, high stress ratio, and long holding time conditions. A Mod.9Cr-1Mo steel, called G91, was developed at ORNL (Oak Ridge National Laboratory, USA) and was adopted as a high-temperature structural material in the ASME Code in 2004. However, its low-cycle fatigue and fatigue crack growth characteristics have been rarely studied. In this work, we have investigated the low-cycle fatigue crack growth behaviors of G91 steel under various test conditions in terms of temperature and stress ratio. As temperature and stress ratio increase, the crack growth rate becomes faster and striation distance also increases. On the other hand, the number of branch cracks decreases.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.1990-2001
• /
• 1991

The fatigue life and crack penetration behavior of high strength steel have been studied in detail both experimentally and analytically. The fatigue crack shape of a smooth specimen is almost semicircular, while a specimen with stress concentration becomes semielliptical according to stress concentration shape. The aspect ratio of smooth specimens calculated using the Newman-Raju's formular is smaller than the value obtained from the experiment. On the other hand, the aspect ratio of the stress concentration specimen shows a good agreement with experimental results. It is found that the crack growth behavior on the back surface after the penetration is unique and can be divided into three stages ; rapid growth region, constant growth region and acceleration growth region. By using the K value suggested in this study, the particular crack growth behavior and crack shape can be estimated quantitatively.