• 터널과지하공간
• /
• 제19권2호
• /
• pp.86-94
• /
• 2009

암석파괴역학과 파괴인성(rock fracture toughness) 이하의 응력확대계수(stress intensity factor)에서 균열이 성장하는 현상을 이용하여 암석 절리면의 비선형 강도특성과, 시간의 경과에 따라 파괴가 진행되는 특성을 고려한 수치해석용 3차원 절리면 요소를 개발하였다. 이 절리면 요소를 사용하여 암석 절리면 전단시험을 수치해석으로 모사한 결과, 전단응력이 증가하고 시간이 경과함에 따라 절리면 사이에 연결된 절리면 내 접점(asperity in joint)에서 암석의 파괴인성보다 응력확대계수가 작음에도 불구하고 균열이 발생하였고 시간이 경과하면서 균열이 성장, 절리면 내 접점이 파괴되었다. 이와 같이 각각의 절리면 내 접점의 파괴에 따라 절리면의 강도는 감소하고, 절리면의 전단응력은 응력경화와 응력연화 후 잔류응력에 도달하는 비선형거동을 보이면서 시간의 경과에 따라 점진적으로 파괴되었다.

• 소성∙가공
• /
• 제9권6호
• /
• pp.653-662
• /
• 2000

Wrinkling is one of the major defects in sheet metal products together with tearing, springback and other geometric and surface defects. The initiation and growth of wrinkles are influenced by many factors such as stress ratios, mechanical properties of the sheet material, geometry of the workpiece, contact condition, etc. It is difficult to analyze the wrinkling initiation and growth considering all the factors because the effects of the factors are very complex and the wrinkling behavior may show a wide scatter of data even for small deviations of factors. The finite element analyses of the wrinkling initiation and growth in the sheet metal forming process provide the detailed information about the wrinkling behavior of sheet metal. The direct analyses of the wrinkling initiation and growth, however, bring about a little difficulty in complex industrial problems because it needs large memory size and long computation time. In the present study, therefore, a global-local analysis technique is introduced for the computational efficiency. Through the analysis of wrinkling in the door inner stamping process, the efficiency of the global-local analysis technique is investigated.

• 대한의용생체공학회:의공학회지
• /
• 제41권1호
• /
• pp.1-7
• /
• 2020

Polyvinyl alcohol (PVA)/gelatin hydrogels were prepared by repeating freezing/thawing three times to evaluate the influence of PVA concentration on the strength and the cell growth behavior of the PVA/gelatin hydrogels. The swelling rate of the PVA/gelatin hydrogels decreased with raising the PVA content from 6 wt% to 12 wt% due to the formation of 3-D network inside the hydrogel. No appreciable degradation of the hydrogels was detected. As the PVA content increased from 6 wt% to 12 wt%, the strength of the PVA/gelatin hydrogels increased drastically from 6.4±0.9 kPa to 46.6±9.0 kPa. The PVA/gelatin hydrogels did not show any evidence of causing cell lysis or toxicity, implying that the hydrogels are clinically safe and effective. Although the strength increased with increasing the PVA content, the PVA/gelatin hydrogels containing 8 wt% exhibited the fastest cell growth, which is highly suitable for wound dressing requiring fast healing regeneration.

• 전산구조공학
• /
• 제10권4호
• /
• pp.229-238
• /
• 1997

본 논문에서는 반복하중에 의해 손상을 입은 아스팔트 콘크리트의 점탄성 구성모델에 대한 역학적 접근방법을 제시하였다. 모의변수로 나타낸 탄성-점탄성 일치원리는 아스팔트 콘크리트의 점탄성과 시간의존 손상의 증가를 별도로 평가하도록 적용되었다. 선형-점탄성 파괴역학에 사용되고 있는 미소균열의 증가법칙이 물체내 손상증가를 나타내는데 성공적으로 사용되었다. 응력과 모의변형도로 나타나는 구성방정식은 먼저 변형도조절에 대해 세워졌으며, 응력과 모의변형도를 모의응력과 변형도로 간단하게 대체함으로써 응력조절 구성방정식으로 변형되었다. 모의응력으로 나타낸 변형된 구성방정식은 응력조절모드에서 파괴에 이르는 아스팔트 콘크리트의 모든 역학적 거동을 충분히 예측하고 있다.

• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.441-447
• /
• 2003

When a SnO$_2$ thin film was deposited by thermal CVD, two different types of growth behavior that were dependent on the deposition temperature were observed. The film grown at 475$^{\circ}C$ had a wide grain size distribution and a faceted surface shape. On the other hand, the film grown at 5$25^{\circ}C$ had a relatively narrow grain size distribution and a rounded sulfate shape. The aspects of grain shape and growth behavior agree well with the theory of gram growth and a roughening transition. The charge tarrier density decreased with deposition time. According to photoluminescence measurements, the peak intensity of the spectra occurred at approximately 2.5 eV, which is related to oxygen vacancies, and decreased with increasing of deposition time. These measurement results suggest that the number of oxygen vacancies, which is related to the electrical conductivity, decrease with deposition time.

• Journal of Welding and Joining
• /
• 제5권3호
• /
• pp.53-61
• /
• 1987

Post weld heat treatment(PWHT) is usually carried out to remove the residual stress and to improve the microstructure and mechanical properties of welded joints. By the way, welding structure transformed owing to PWHT and reheating for repair loads the random cycles fatigue as offshore welding structure of constant low cycle fatigue as pressure vessel, and then, pre-existing flaws or cracks exist in a structural component and those cracks grow under cyclic loading. Therefore, the effects of PWHT and stress ratio on fatigue crack growth behaviors were studied on the three regions such as HAZ, sub-critical HAZ and deposit metal of welded joints in SM53 steel. Fatigue crack growth behavior of as-weld depended on microstructure and fatigue crack growth rate of HAZ was the lowest at eac region, but after PWHT it was somewhat higher than that of as-wel. In case of applying the stress($10kg/mm^2$) during PWHT, fatigue crack growth resistance tended to increase in the overall range of .DELTA.K.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.233-243
• /
• 2017

This paper describes an investigation on the effect of using three different filler metals on fatigue behavior of mechanical structures welded. The welding is carried out on the steel A510AP used for the manufacture of gas cisterns and pipes. The welding process used is manual welding with coated electrodes and automatic arc welding. Compact tension CT50 specimen has been used. The three zones of welded joint; filler metal FM, heat affected zone HAZ and base metal BM have been investigated. The results show that the crack growth rate CGR is decreasing respectively in BM, FM and HAZ; however, this variation decreases when stress intensity factor SIF increases. For low values of SIF, the CGR is inferior in the over-matched filler metal of which the value of mismatch M is near unity, but for high values of M the CGR is superior, and the effect of the over-matching on CGR becomes negative. No deviation of the crack growth path has been noticed.

• Structural Engineering and Mechanics
• /
• 제72권3호
• /
• pp.313-327
• /
• 2019

Damage evolution in the form of void nucleation, propagation and coalescence is the primary cause that is responsible for the ductile failure of microalloyed steels. The Gurson-Tvergaard-Needleman (GTN) damage model has proven to be extremely robust for characterizing the microscopic damage behavior of ductile metals. Nonetheless, successful applications of the model on a given metal type are limited by the correct identification of damage parameters as well as the validation of the calculated void growth rate. The purpose of this study is two-fold. First, we aim to identify the damage parameters of the GTN model for Q345 steel (Chinese code), due to its extensive application in mechanical and civil industries in China. The identification of damage parameters is facilitated by the well-suited response surface methodology, followed by a complete analysis of variance for evaluating the statistical significance of the identified model. Second, taking notched Q345 cylinders as an example, finite element simulations implemented with the identified GTN model are performed in order to analyze their microscopic damage behavior. In particular, the void growth rate predicted from the simulations is successfully correlated with experimentally measured acoustic emissions. The quantitative correlation suggests that during the yielding stage the void growth rate increases linearly with the acoustic emissions, while in the strain-hardening and softening period the dependence becomes an exponential function. The combined experimental and finite element approach provides a means for validating simulated void growth rate against experimental measurements of acoustic emissions in microalloyed steels.

• 한국결정성장학회지
• /
• 제30권3호
• /
• pp.110-116
• /
• 2020

MLCC(Multi-Layer Ceramic Capacitor)의 유전체 층에 사용되는 BaTiO₃ 입자는 안정한 TCC(Temperature Characteristics of Capacitance) 거동을 갖기 위해 core/shell 구조를 갖는다. 지금까지 shell의 특성은 core/shell 구조의 전체 특성에서 유추해 왔다. 이는 core/shell 구조가 겨우 수 ㎛의 작은 크기로 shell 특성만 구별해서 측정하기가 어렵기 때문이다. 본 실험에서는 micro-contact법을 이용하여 확산쌍 시편의 계면에 형성된 확대된 core/shell 구조에 Pt 전극을 증착하여 35~135℃ 에서 shell 영역의 독립적인 TCC 거동을 측정하였다. 그 결과, 65℃에서 최대 유전율 값을 갖는 완만한 피크의 확산 상전이(Diffusion Phase Transition) 거동인 core의 특성과 구별되는 거동을 관찰하였으며, 이는 core/shell 구조의 온도-유전거동을 묘사하는 모델링에서 실험 자료로 활용될 것으로 본다.

• 한국세라믹학회지
• /
• 제29권12호
• /
• pp.949-955
• /
• 1992

R-curves, fracture resistance (KR) as a function of crack extension (Δa), of a gas-pressure sintered monolithic Si3N4 were determined by controlled flaw/strength technique. Rising R-curve behavior was observed, confirming the operation of microstructural toughening process during crack growth. The R-curve parameters, k and m in the equation, KR=k(Δa)m, were determined to 30.301 and 0.1146, respectively. Microstructural observation of growing crack revealed that the bridging in the crack wake by unbroken ligament of large elongated ${\beta}$-grains was the mechanism primarily for the rising R-curve behavior.