• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1980-1992
• /
• 2006

Nucleate pool boiling experiments were performed using pure R11 for various surface angles under constant heat flux conditions during saturated pool boiling. A 1-mm-diameter circular heater with an artificial cavity in the center that was fabricated using a MEMS technique and a high-speed controller were used to maintain the constant heat flux. Bubble growth images were taken at 5000 frames per second using a high-speed CCD camera. The bubble geometry was obtained from the captured bubble images. The effects of the surface angle on the bubble growth behavior were analyzed for the initial and thermal growth regions using dimensional scales. The parameters that affected the bubble growth behavior were the bubble radius, bubble growth rate, sliding velocity, bubble shape, and advancing and receding contact angles. These phenomena require further analysis for various surface angles and the obtained constant heat flux data provide a good foundation for such future work.

• 한국분말재료학회지
• /
• 제13권2호
• /
• pp.119-123
• /
• 2006

The grain growth behavior of $0.95Na_{1/2}Bi_{1/2}TiO_{3}-0.05BaTiO_{3}$ (NBT-5BT) has been investigated with respect to the grain shape. The powder compacts of NBT-5BT were sintered at 1200 for various times. The corresponding equilibrium shape was a round-edged cube with flat {100}-faces. Abnormal grains were not observed in the specimens sintered for 1 to 12 h but abnormal grains appeared when sintered for 24 h. Before the formation of abnormal grains, a valley was observed in the measured grain size distribution of NBT-5BT, showing that the grain size distribution was a combination of two unimodal distributions. The present result suggests that the grain growth in NBT-5BT was governed by the growth of facet planes which would occur via 2-dimansional nucleation and growth.

• 한국해양공학회지
• /
• 제14권1호
• /
• pp.23-28
• /
• 2000

The fatigue crack growth behavior of the cold-rolled STS 304 steel developed for membrane material of LNG storage tank was examined experimentally at 293K, 153K and 111K. The fatigue crack growth rate(do/dN) tends to increase as the stress ratio (R) increases over the testing temperature when compared at the same stress intensity factor range($\Delta$K). The effect of R on do/dN is more explicit at low temperatures than at room temperature. The resistance of fatigue crack growth at low temperatures is higher compared with that at room temperature which is attributed to the extent of strain-induced martensitic transformation at the crack tip. The temperature dependence of fatigue crack growth resistance is gradually vanished with an increase in $\Delta$K which correlates with a decreasing fracture toughness with decreasing temperature. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperature are mainly explained by the crack closure and the strengthening due to the martensitic transformation.

• Journal of Welding and Joining
• /
• 제7권1호
• /
• pp.28-35
• /
• 1989

The fatigue crack growth behavior in GTA butt welded joints of Al-Alloy 5052-H38 was examined using Single Edge Notched(SEN) specimens. It is well known that welding residual stress has marked influence on fatigue crack growth rate in welded structure. In the general area of fatigue crack growth in the presence of residual stress, it is noted that the correction of stress intensity factor (K) to account for residual stress is important for the determination of both stress intensity factor range(.DELTA.K) and stress ratio(R) during a loading cycle. The crack growth rate(da/dN) in welded joints were correlated with the effective stress intensity factor range(.DELTA.Keff) which was estimated by superposition of the respective stress intensity factors for the residual stress field and for the applied stress. However, redistribution of residual stress occurs during crack growth and its effect is not negligible. In this study, fatigue crack growth characteristics of the welded joints were examined by using superposition of redistributed residual stress and discussed in comparison with the results of the initial welding residual stress superposition.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.200-208
• /
• 2021

This paper investigated generation behavior of micro-arcs and growth behavior of PEO films on the AA7050 disc specimen in 0.1 M NaAlO₂ solution under the application of 1200 Hz anodic pulse current. Morphologies, thickness and surface roughness of PEO films were examined at the edge part and central part separately. Micro-arcs were generated first at the edge part and then moved towards the central part with PEO treatment time, indicating lateral growth of PEO films. The lateral growth resulted in uniform PEO thickness of about 5 ㎛ and surface roughness of about 0.5 ㎛. Moving of the arcs from the edge towards the central part appeared only one time and large size arcs were generated at the edge before completing the central part with small size micro-arcs. This suggests that vertical growth starts before completing the lateral growth. Large size arcs generated at the edge resulted in the formation of relatively large size pores within the PEO films on the AA7050 disc specimen.

• Asian-Australasian Journal of Animal Sciences
• /
• 제29권6호
• /
• pp.879-886
• /
• 2016

As is in all economic activities, the highest yield per unit area is the main goal in animal production, while addressing the temperamental needs of animals often is ignored. Animal welfare is not only an ethical fact; it also has an economic value. Spatial environmental enrichment contributes positively to animal welfare by addressing their behavioral and mental requirements. The present study was conducted to determine the effects of weaning and spatial environmental arrangements on behaviors of goat-kids. Experimental groups were arranged in structured and unstructured spatial environments. Roughage feeder, semi-automatic concentrate feeder, bunk, bridge, and wood block were placed in the structured environment. No equipment was placed in the unstructured environment and paddock sides were enclosed with an iron sheet to prevent bipedal stance and to provide environmental isolation. In the study 10 male and 10 female Turkish Saanen goat kids were used in each group. Spatial environmental arrangements did not have significant impacts on the growth performance of kids (p>0.05). All objects in the structured group were accepted by the kids. Average use ratios of roughage feeder, semi-automatic concentrate feeder, bunk, bridge and wood block were observed as 19.3%, 14.0%, 12.6%, 3.8%, and 0.7%, respectively. There were significant differences between before- and after-weaning in use of all objects except for underneath bridge ($p{\leq}0.05$). Concentrate feed consumption, locomotion, and resting behaviors in kids showed significant differences by structural group and growth period. Roughage consumption was similar between groups, while it differed by growth period ($p{\leq}0.05$). Interaction frequency was significantly higher in structured group (p = 0.0023). Playing behavior significantly differentiated based on the growth period rather than on groups ($p{\leq}0.05$). Playing behavior significantly decreased after weaning. Abnormal oral activity was significantly higher in the structured group before weaning ($p{\leq}0.05$). Despite there being no installations facilitating climbing and bipedal stance, the kids of the unstructured group were able to exhibit 1/3 as much bipedal stance behavior as the kids of the structured group through leaning over slippery paddock wall or over their groupmates. Bipedal stance behavior of unstructured group was similar before and after weaning, while bipedal stance behavior before weaning was about 2 times that of after weaning in structured group. It was concluded that unstructured environmental arrangement limited the behavior repertoire of the goat kids.

• 기술혁신학회지
• /
• 제20권3호
• /
• pp.754-780
• /
• 2017

본 연구는 일과 삶의 균형(WLB:Work-Life Balance)의 한 영역인 일 성장 균형(WGB: Work-Growth Balance)이 대인 조화와 창의적 노력 및 조직 내 혁신 행동을 향상시키는지 여부, 그리고 대인 조화와 창의적 노력이 일 성장 균형(WGB)과 혁신 행동 간의 관계에 간접 효과가 있는지 여부를 알아보기 위해 수행되었다. 본 연구의 가설 검증을 위해서는 Hayes(2013)의 PROCESS Macro를 활용하였다. 분석결과 혁신행동에 영향을 주는 것은 일 성장 균형(WGB)과 대인조화 그리고 창의적 노력으로 나타났고 대인조화에 영향을 주는 변수 역시 일 성장 균형(WGB)으로 나타났다. 또한 창의적 노력에 영향을 미치는 변수는 일 성장 균형(WGB)과 대인조화였다. WGB와 혁신행동 사이의 관계에서 대인조화와 창의적 노력의 간접 효과 역시 확인되었다. 더불어 PROCESS Macro 분석을 통하여 매개변수 간의 효과의 크기를 알아보았다. 이를 통해 일 성장 균형(WGB)이 대인조화, 창의적 행동 및 혁신행동 간에는 시너지 관계가 존재함을 알 수 있었다. 향후 다양한 다른 산업 간의 일 성장 균형(WGB)에 대한 연구와 일 성장 균형(WGB)과 혁신행동에 이르는 좀 더 다양한 매개변수에 대한 연구 그리고 일 가정 균형, 일 여가 균형에 대한 추가 연구도 기대된다.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.1013-1022
• /
• 1995

A hybrid composite (APAL;Aramid Patched ALuminum alloy, CPAL;Carbon Patched ALluminum alloy), consisting of a Al 2024-T3 aluminum alloy plate sandwiched between two aramid/epoxy and carbon/epoxy laminate, was developed. Fatigue crack growth behavior was examined at stress ratios of R=0.2, 0.5. The APAL and CPAL showed superior fatigue crack growth resistance, which may be attributed to the crack bridging effect imposed by the intact fibers in the crack wake.

• 한국결정성장학회지
• /
• 제7권4호
• /
• pp.560-566
• /
• 1997

Seeded vapor transport법에 의해 성장된 ZnSe 결정내에서 전위거동을 살펴보았다. (111)과 (100) ZnSe wafer의 etch pit 형상을 관찰하였고 성장된 결정이 높은 전위밀도를 가지면 전위들이 lineage와 cellular 두 가지 형태로 배열됨을 알았다. Seed로부터 측방성장된 부위에서 전위밀도의 변화는 없었으나 수직 성장방향으로는 전위밀도가 감소하였고, 같은 wafer내에서 전위밀도는 wafer center 지역의 전위밀도가 edge부위의 전위밀도 보다 낮았다. 성장된 결정의 평균 전위밀도는 $4{\times}10^4 /\textrm{cm}^2$이었다.

• 대한기계학회논문집A
• /
• 제21권8호
• /
• pp.1175-1187
• /
• 1997

Densification behavior and grain growth of zirconia powder compacts are investigated under high temperature. Experimental data are obtained for zirconia powder under pressureless sintering, sinter forging and hot isostatic pressing. The constitutive equations by Kwon et al. are used for diffusional creep and grain growth. The constitutive equations by McMeeking and co-workers are also included to study the effect of power-law creep. These constitutive equations are implemented into a finite element program (ABAQUS) to investigate the friction effect during sinter forging and the canning effect during hot isostatic pressing. The agreements between experimental data and finite element results are very good in pressureless sintering and hot isostatic pressing, but not as good in sinter forging.