• 열처리공학회지
• /
• 제10권3호
• /
• pp.165-171
• /
• 1997

Laser hardening for the piston ring groove of ductile cast iron was tried. Mechanical and microstructural investigation for the hardened area indicated that the laser heating technique could replace conventional induction hardening process completely and further showed that post grinding process would be eliminated by minimizing bulging of heat treated area. In laser hardening, the volume increase caused by martensitic phase transformation proved to be less than $10{\mu}m$, which insures no post machining on the hardened surface. As expected, the depth of hardening was inversely proportional to the beam scanning velocity and the highest surface hardness was obtained at the beam velocity of 0.75m/min. Heat treatment using phosphate coating demonstrated quite comparable result to the case of graphite suscepter.

• 대한기계학회논문집A
• /
• 제28권1호
• /
• pp.79-84
• /
• 2004

A light-guide is one of several important components of backlight unit in TFT-LCD. The manufacturing technology and optical system design of the light guide is very sensitive to quality and cost of the TFT-LCD module. In the present study a new manufacturing method which is called as direct surface forming(DSF) has been tested under various conditions. DSF is very similar to the well-known hot embossing except for partial contact between mold and substrate. The final V-groove pattern shows different shapes depend on the temperature of mold surface, contact time of mold and depth of V-groove.

• 설비공학논문집
• /
• 제16권8호
• /
• pp.691-697
• /
• 2004

Experimental study is carried out to investigate the heat transport capability and thermal resistance of sinusoidal axially grooved heat pipe, comparing its performance to trapezoidal axially grooved heat pipe. As a result from this work, the heat transport capability of sinusoidal grooved heat pipe is lower than that of trapezoidal grooved heat pipe for the same size of outer diameter. As the ratio of depth to width of sinusoidal groove heat pipe is higher, the heat transport capability of heat pipe becomes higher. It is found that Aluminum-ammonia heat pipes with sinusoidal and trapezoidal grooves have good thermal resistance, below 0.1$^{\circ}C$/W at evaporator section and below 0.05$^{\circ}C$/W at condenser section.

• 한국기계가공학회지
• /
• 제9권4호
• /
• pp.8-13
• /
• 2010

The constant velocity internal grinding is a popular process for studying axle machine design and process in automobile industry. In this study, The program which gives the data of wheel size and truing diameter of ball groove is developed. As a result I obtained the data of grinding conditions makes good surface roughness get a grinding conditions. The grinding characteristics and conditions of constant velocity joint were investigated with respect to grinding feed, cutting depth, grinding time. At machine failure, the results were suddenly increased and the detailed surfaces were extremely obtained. Grinding condition was big more affected by grinding depth, grinding speed and grinding time.

• Tribology and Lubricants
• /
• 제13권4호
• /
• pp.40-46
• /
• 1997

The externally pressurized air journal bearings which have two circumferential grooves with inherently compensated restrictors are analyzed. Two circumferential grooves with restrictors are made on the bearing surface in order to increase the stiffness and damping coefficients. In this paper, the dynamic characteristics such as stiffness and damping coefficients of this type of bearings are calculated. As a result of theoretical analysis, it is verified that there exist the groove depth and the distance between two grooves which generate the maximum stiffness at the given bearing dimensions.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 제18회 학술대회 초록집
• /
• pp.51-56
• /
• 1993

The conical bearing can be used to support the radial and thrust load simultaneously. Two circumferential grooves with discrete hole restrictions are made on the bearing surface in order to increase stiffness. In this paper, the dynamic characteristics of this type of bearings are calculated such as stiffness and champing coefficients. As a results of theoretical analysis, it is verified that there exist the groove depth and distance between two grooves which produce the maximum stiffness at the given bearing dimensions.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.356-363
• /
• 2001

Piston seal is a device designed to prevent leakage in split connecctions or between relatively moving part. Contact force, critical pressure at which extrusion occurs, leakage rate, fluid film thickness and friction force have been analyzed for some design parameter such as clearance between cylinder wall piston, depth of rectangular groove and pressure of sealed hydraulic fluid. In this paper, we analyze displacement and stress of Wearing by finite element analysis to understand Contact Behaviour Characters.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.56-61
• /
• 1994

The conical bearing can be used to support the radial and thrust load simultaneously. Two circumferential grooves with discrete hole restrictions are made on the bearing surface in order to increase stiffness. In this paper, the dynamic characteristics of this type of bearings are calculated such as stiffness and damping coefficients. As a results of theoretical analysis, it is verified that there exist the groove depth and distance between two grooves which produce the maximum stiffness at the given bearing dimensions.

• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.408-413
• /
• 2013

Micro-features such as grooves and lenses, which perform optical functions in flat displays, should be manufactured with a good form accuracy because this is directly related to their optical performance. As the size of the display increases, it is very difficult to maintain a high relative accuracy because of the inherent geometric errors such as the waviness of a large-area plate. In this paper, the optical effect of these geometric errors is investigated, and surface-referenced micro-grooving to measure and compensate for such geometric errors on line is proposed to improve the form accuracy of the micro-grooves. A PZT-based fast depth adjustment servo system is implemented in the tool holder to maintain a uniform groove depth in reference to the wavy surface. Through experiments, the proposed method is shown to be an efficient way to produce high-quality micro- grooves on a wavy die surface.

• 한국생산제조학회지
• /
• 제23권1호
• /
• pp.69-74
• /
• 2014

An OrthoMTA compacter is made by machining a Ni-Ti alloy wire using tapered helix creep-feed grinding machines. This aim of this study is to find the optimal dressing conditions to sharpen the corner of a cubic boron nitride (CBN) wheel. On the basis of the results of various experiments, it is verified that the most important factors in dressing are the dressing depth and feeding method, whereas the feed rate has less importance for producing a smaller corner R value. The study also finds the optimum dressing depth to reduce the dressing time, a feeding speed and method to stabilize the machining, and the mesh grade for the CBN wheel to make the groove of the compacter deeper.