• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.787-792
• /
• 2000

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and the material removal are measured and discussed. The results are as follows.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.47-53
• /
• 2003

It was already proven experimentally that the laminated grinding wheel is superior to the general grinding wheel in the productivity of grinding. However, it can't be guaranteed when the workpiece material is cemented carbide. Because of its extreme hardness, the grinding wheels made up of super-abrasives are used for grinding it. So, to investigate the performance in extremely hard materials grinding using super-abrasive grinding wheels, the surface roughness characteristics of cemented carbide ground by the laminated diamond wheels are studied experimentally. Through this study, it is found that the similar surface roughness characteristics, those were found in the studies on the laminated aluminum oxide wheels, are still available.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.113-118
• /
• 1994

An experimental investigation on the wear of alumina grinding wheel is presented. The experiments consist of the measurements of fracture strength of the abrasive grains, grinding forces, and the area of wear flats of grinding wheels. Microscopic examinations of abrasive grains were also carried out to observe the progress of wheel wear. the results show that the 32A grain, which has relatively lower fracture strength, wears out faster than 5SS and 5SG. The wheel wear occurs much faster in wet grinding than in dry grinding. It has also been found that the grinding forces increase logarithmically with increasing wear flats.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.28-31
• /
• 2002

This paper compared the surface roughness with variables before development of centerless grinding using far ferrule machining. In this paper, theoretical surface roughness is obtained from variables such as mesh number, rate of concentration of grinding wheel, wheel rotation of work-piece etc., and optimum condition of machining is selected. For satisfaction the technical side and economical side, centerless grinding using fur ferrule machining should be designed more than #600, 18.8% rate of concentration of grinding wheel, 1440rpm wheel rotation outwork-piece.

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.16-25
• /
• 1999

In recent years, grinding techniques for precision machining of brittle materials used in die, model and optical parts have been improved by using superfine abrasive wheel and precision grinding machine. The completion of optimum dressing of superfine abrasive wheel makes possible the effective precision grinding of die steel(STD-11). In this study, a new system and the grinding mechanism of optimum in-process electrolytic dressing were proposed. This method can carry out optimum in-process electrolytic dressing of superfine abrasive wheel. Therefore, the optimum in-process electrolytic dressing is a good method to obtain the efficiency and mirror-like grinding of STD-11.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 춘계학술대회 논문집
• /
• pp.17-23
• /
• 1995

This paper describes investigation of the dressing time by laser in the surface grinding operation. Always dressing work is done before grinding operation. And then generates wear and roading on the wheel by contact between the grinding performance but also ground surfaces. On these states dressing work is needed. On this paper contour of the wheel by He-Ne laser is measured. It has also been found that the wheel deflection reduces the actual depth of cut and the roughness of the ground surface.

• 반도체디스플레이기술학회지
• /
• 제10권3호
• /
• pp.35-42
• /
• 2011

This paper describes the characteristics of high speed grinding and the influence of wheel surface speed V and a grindability of the grinding materials. The various fine ceramics pieces was ground by metal and vitrified bonded diamond wheel. The surface roughness of fine ceramics(Zirconia($ZrO_2$), Silicon Carbide(SiC), Silicon Nitride($Si_3N_4$), Alumina($Al_2O_3$)) decreases from $0.05{\mu}m(R_{max})$ to $0.025{\mu}m(R_{max})$ when the wheel speed at grinding point increases the wheel speed. Relation between the temperature at grinding point and surface roughness was linear. Abrasive jet machining(AJM), a specialized from of shot blasting, is considered one of the most helpful micro machining methods for hard and brittle materials such as glasses and ceramics by constant pressure grinding.

• 한국정밀공학회지
• /
• 제16권10호
• /
• pp.118-125
• /
• 1999

In the grinding process, generally, the exciting forces with high frequency can be generated due to the wheel wear and the grinding process. As the grinding speed increases, the precise investigation about the wheel dynamic characteristics is required. Conventionally the wheel-spindle has been considered with lumped model in dynamic modeling. With this lumped model, the significant mode resulted from the shell mode of wheel can be readily ignored. This paper suggests the new analysis model which includes the shell mode of wheel in modeling the wheel-spindle assembly. Furthermore, based on the suggested model, the effects of the bolt tightening force and the taper tightening force on the dynamic properties are investigated by the finite element modal analysis and the experimental method. As a result of investigation, the shell mode vibration of wheel affects the dynamic characteristics of the spindle assembly. Also, the vibration modes of the spindle assembly are significantly affected by the joint tightening forces.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권1호
• /
• pp.32-37
• /
• 2007

The outer diameter finishing grinding process required for ferrules, which are widely used as fiber optic connectors, is carried out by high-precision centerless grinding machines. In this study, the thermal characteristics of such a machine, for example, the temperature distribution, temperature rise, and thermal deformation, were estimated based on a virtual prototype and the heat generation rates of heat sources related to normal operating conditions. The prototype consisted of a concrete-filled bed. hydrostatic grinding wheel (GW) and regulating wheel (RW) spindle systems, a hydrostatic RW feed mechanism, a RW swivel mechanism, and on-machine GW and RW dressers. The reliability of the predicted results was demonstrated using temperature characteristics measured from a physical prototype. The predicted and measured results indicated that this particular high-precision centerless grinding machine had very stable thermal characteristics.

• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.34-47
• /
• 2000

Since carbon fiber epoxy composite materials have excellent properties for structures due to their high specific strength, high specific modulus, high damping and low thermal expansion, the hollow shafts made of carbon fiber epoxy composites have been widely used for power transmission shafts for motor vehicles , spindles of machine tools, motor base, bearing mount for tool up and manufacturing. The molded composite machine elements are not usually accurate enough for mechanical machine elements, which require turning drilling , cutting and grinding. The experiment are surface grinding wheel GC60 to the carbon fiber epoxy composite specimen with respect to staking angle [0]nT , [45]nT, [90]nT on the CNC grinding machine. In this paper, the surface grinding characteristics of composite plate, which are surveyed experimentally and analytically with respect to the grinding force, surface roughness and wheel loading according to the variable depth of cut, wheel velocity and table feed rate are investigated.