• Journal of the Korean Solar Energy Society
• /
• v.34 no.3
• /
• pp.66-74
• /
• 2014

In this paper, the performance of Hybrid Dimming control system for Daylighting system is evaluated by accredited tests. The system controls the balance of illuminance of daylight between daylight system and LED light system. It makes the normal illuminance of interior without the effects of weather by controlling the LED depending on the brightness of outside. For the tests, 6 diffusers($600{\times}300mm$) were installed in lighting area($36m^2$) and normal operation of the system sensors were tested about the interference of sunlight. The results of the examinations were satisfied with the criteria of accredited tests. Further research is the verification of energy saving effect by comparing the Hybrid Dimming control system to current artificial light system.

• Current Photovoltaic Research
• /
• v.3 no.1
• /
• pp.1-4
• /
• 2015

In this study, we analyzed the correlation between mechanical and electrical properties of low-temperature conductive film (LT-CF) bonded silicon solar cells by a quadrant analysis (horizontal axis (peeling strength), vertical axis (power loss)). We found that a series of points with various bonding parameters such as bonding temperature, pressure and time were distributed in the different three regimes; weak regime (Q2: weak bonding strength and high power loss), moderate regime (Q4 : strong bonding strength and low power loss) and hard regime (Q3 : weak bonding strength and low power loss). Using this analogous technique, it was possible to fabricate the LT-CF bonded silicon solar cells with the various conditions displayed in Q3 of the quadrant plots, possessing the peeling strength of ~ 1N/mm and power loss of 2~3%.

• Proceedings of the Korean Society of Tobacco Science Conference
• /
• 2003.05a
• /
• pp.32-32
• /
• 2003

• Korean Journal of Materials Research
• /
• v.21 no.12
• /
• pp.679-684
• /
• 2011

One of the trace constituents included in cement clinker, chromium, has become prominent and highly noticed lately as a social issue both inside and outside of this country because it affects the human body negatively. The purpose of the present study was to investigate leaching properties of water-soluble hexavalent chromium by different manufacturing conditions of cement clinker. Raw materials were prepared to add different $SiO_2$, $Al_2O_3$ and $Fe_2O_3$ sources. After the raw materials, such as limestone, sand and clay, iron ore was pulverized and mixed, and the raw meal was burnt at $1450^{\circ}C$ in a furnace with an oxidizing atmosphere. Leaching of soluble hexavalent chromium showed a tendency to decrease with an increasing LSF and IM. However, leaching of soluble hexavalent chromium increased with an increasing S.M. Alkali contents of iron source minerals is closely related to the leaching properties of soluble hexavalent chromium. Green sludge has the highest content of alkali added; leaching of water-soluble hexavalent chromium was mostly high. In order to reduce the water-soluble hexavalent chromium in cement, reducing the alkali content in raw materials is important.

• Journal of Fashion Business
• /
• v.26 no.6
• /
• pp.82-93
• /
• 2022

Sustainability is a significant change that fashion industry has undergone. Marketers and brands are looking for guidance in green advertising to most effectively motivate consumers to purchase sustainable fashion products. This study aims to reveal environmental and cultural sustainability claims on message credibility and purchase intention regarding product trendiness. We performed mediation and moderation analyses, using a 2 (sustainability message: environmental and cultural) × 2 (product design: classic vs. trendy) between-subjects experimental design. The PROCESS MACRO was used for the analysis. Results indicate that environmental claim must appear credible to consumers to motivate them to purchase a product. On the other hand, cultural claim, with and without credibility, affected consumer's purchase intention. Moreover, cultural claim and trendy design together influenced message credibility and purchase intention, showing a moderated mediation effect. The study indicates that brands should broaden their perspective regarding sustainability by considering cultural factors when providing sustainability claims. Environmental claim should be clear and transparent to avoid green skepticism. Also, it is important to focus on product's design aspect: making trendy designs. It is difficult to change consumer behavior based only on sustainability value. Thus, brands must coney their consideration of design trends. Theoretical and managerial implications also are discussed.

• Korean Journal of Materials Research
• /
• v.19 no.10
• /
• pp.538-543
• /
• 2009

Active clays, Diatomite, bentonite and zeolite were used as porous materials for fabricating hygroscopic gypsum boards. Pohang active clay and Cheolwon diatomite showed excellent characteristics of moisture adsorption and desorption. These characteristics were caused by higher surface area and pore volume of porous materials. Moisture adsorption content of gypsum board with 10% active clay(P1) was 62.0 g/m$^2$, and moisture desorption content was 50.2 g/m$^2$. Moisture adsorption content of gypsum board with 10% diatomite(P) was 59.5 g/m$^2$, and moisture desorption content was 49.0 g/m$^2$. Moisture adsorption contents of gypsum boards with porous materials were higher than that moisture desorption contents of gypsum board without porous materials. Correlation coefficient between surface area and moisture adsorption content of gypsum boards was 0.98. Also, correlation coefficient between surface area and moisture desorption content of gypsum boards was 0.97. Moisture adsorption and desorption contents were influenced by surface area and pore volume of the gypsum boards, and surface area had a larger effect on moisture adsorption and desorption.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.181-186
• /
• 2010

Since it was developed by Joseph Aspdin, cement has been a common construction materials up to the present time. However, there are trace constituents in cement clinker. One of the trace constituents included in cement clinker, chromium, has become prominent and highly noticed lately as a social issue both inside and outside of this country because it affects the human body negatively. The aim of the present study was to investigate the concentration of water-soluble hexavalent chromium in cement clinker by using industrial by-products. For that reason, raw materials were prepared to add different $SiO_2$, $Al_2O_3$, and $Fe_2O_3$ sources. After the raw materials such as the limestone, the sand and the clay, iron ore was pulverized and mixed, and the raw meal was burnt at about $1450^{\circ}C$ in a furnace with an oxidizing atmosphere. The part in the raw materials of the clinker was substituted with slag, sludge, etc. and this was used to manufacturing cement clinker. To investigate the water-soluble hexavalent chromium content in clinker, raw meal was prepared by changing the modulus, the type, and the content of clinker materials and tested concentrations of hexavalent chromium in the clinkers. To determine $Cr^{+6}$ formation of the clinker, tests were done with raw meals adding chromium by using different industrial by-products. Consequently because the chromium was to be included in the raw materials of the clinker, production of Portland cement clinker was included with the chromium. Also, the chromium was converted into hexavalent chromium in the burning process.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.664-667
• /
• 2001

Segregation of binary particle systems in a horizontally gyrated bed has been experimentally studied to recover the heavy metals from municipal waste incineration (MWI) ash. Differences in density and size had less effect on segregation. Effective segregation took place under the centrifugal effect of 1 or less for any particle size ratio. Zn, Cu and Pb were concentrated in the upper side of bed by the horizontal vibration. However, there was less change in concentration for other metals such as Mg, Al and Fe etc. The separation system with the horizontal gyrating separator proved to be an effective method for the pretreatment of recovering Zn, Cu and Pb from incineration residues.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.64-68
• /
• 2003

For the purpose of the efficient derivation of the closed-form Green's functions by which MoM matrix elements can be analytically evaluated, the optimum approximation path which is deformed from the Sommerfeld integration path on the complex $k_{\rho}$-plane is proposed based upon the steepest descent method and three level approximation procedure.

• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.63-66
• /
• 2001

In order to derive simple and accurate closed-form spatial Greep’s functions for the thick microstrip substrate, an efficient method based on the two-level approach, which circumvents the burdensome steps (i.e., without necessity of extraction of quasi-static contributions and subsequent determination of approximation parameters) in the previous complex image method, is considered in conjunction with the use of the original Prony`s method. The present method is observed to give more accurate results for the evaluation of the Green`s functions over wider frequency range independently of the source-to-field distances than the previous method.