• 제목/요약/키워드: gravity shear ratio

검색결과 38건 처리시간 0.029초

중력전단비에 따른 철근콘크리트 플랫 플레이트 골조의 내진 성능 평가 (Seismic Performance of Reinforced Concrete Flat Plate Frames according to Gravity Shear Ratio)

  • 황보진;한상환;박영미
    • 콘크리트학회논문집
    • /
    • 제22권1호
    • /
    • pp.3-10
    • /
    • 2010
  • 이 연구에서는 중력 전단비에 따른 철근콘크리트 플랫 플레이트 골조의 내진성능을 평가하였다. 이를 위하여, 이 연구에서는 3층, 7층 골조를 중력하중만 고려하여 설계하고, 대상 건물에 대한 비선형 정적 푸쉬 오버 해석과 비선형 동적 해석을 수행하였다. 그리고 이 연구는 그 비선형 해석에서 중력 전단비의 차이에 따른 뚫림 전단과 파괴 메커니즘을 예측할 수 있도록 제안한 슬래브-기둥 접합부 모델을 사용하였다. 이 연구 결과에 따르면 중력 전단비가 골조의 내진성능에 큰 영향을 미치는 것으로 나타났다. 특히 중력 전단비가 커짐에 따라 골조 접합부의 파괴가 취성적인 파괴를 나타내어 내진 성능이 떨어지는 것으로 나타났다.

내진성능평가시 횡보강근이 없는 RC 보-기둥 접합부의 전단내력 평가 (Seismic Assessment of Shear Capacity of RC Beam-Column Joints Without Transverse Re-bars)

  • 이영욱
    • 한국지진공학회논문집
    • /
    • 제23권5호
    • /
    • pp.249-259
    • /
    • 2019
  • To study the seismic resistance of the shear capacity of the RC beam-column joints of two-story and four-story RC buildings, sample buildings are designed with ordinary moment resisting frame. For the shear capacity of joints, the equations of FEMA 356 and NZ seismic assessment are selected and compared. For comparison, one group of buildings is designed only for gravity loads and the other group is designed for seismic and gravity loads. For 16 cases of the designed buildings, seismic performance point is evaluated through push-over analysis and the capacity of joint shear strength is checked. Not only for the gravity designed buildings but also for seismic designed buildings, the demand of joint shear is exceeding the capacity at exterior joints. However, for interior joint, the demand of joint shear exceeds the capacity only for one case. At exterior joints, the axial load stress ratio is lower than 0.21 for gravity designed buildings and 0.13 for seismic designed buildings.

플랫 플레이트 외부접합부의 불균형모멘트에 관한연구 (A Study on Unbalanced Moment of Flat Plate Exterior Connections)

  • 최현기;백성우;백영수;진언식;최창식
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
    • /
    • pp.1-4
    • /
    • 2008
  • 플랫 플레이트 구조는 다른 구조형식에 비하여 매우 경제적인 구조형식이다. 그러나 횡하중을 받는 플랫 플레이트 구조는 슬래브-기둥 접합부의 뚫림전단파괴에 대해 취약하다. 플랫 플레이트 구조의 외부접합부는 편심전단에 대해 비대칭형의 위험단면을 가지고 있으며, 위험단면의 길이가 내부접합부 보다 작고 중력하중과 횡하중 모두에 의해 편심전다응력이 발생하게 되므로 뚫림전단파괴에 대해 매우 취약하다. 이에 본 논문에서는 플랫 플레이트 외부접합부의 실험결과와 기존 데이터를 바탕으로 ACI 318-05와 CEB-FIP MC 90의 설계기준식을 비교한 결과 편심전단응력, 불균형모멘트에 대해서 CEB-FIP식이 더 정확했고 형상비의 영향은 기둥 형상비가 큰 경우에는 기준식의 적용성에 문제가 있는 것으로 나타났다. 중력전단력비의 영향은 기준식의 제안을 만족하였으나 설계 기준에서는 단순히 중력전단비만 고려하고 있어서 다른 설계조건 변화에 따른 차이를 고려할 필요가 있다.

  • PDF

횡하중을 받는 내부 슬래브-기둥 접합부의 거동 (Behavior of Interior Slab-Column Connections under Lateral Load)

  • 권대홍;최명신;안종문;이광수;신성우
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
    • /
    • pp.154-157
    • /
    • 2006
  • An experimental study was conducted to study the behavior of slab-column connections under lateral load. Test variables include gravity shear ratio$(V_g/V_o=0.3,\;0.5)$ and flexural reinforcement ratio of slab(p=0.01, 0.015). Strength and ductility of tested specimens were evaluated in accordance with gravity shear ratios and slab reinforcement ratios. Shear stresses of Code's equation at the critical section were also compared with experimental results.

  • PDF

개구부를 갖는 콘크리트 전단벽의 탄성안정 (Elastic Stability of Perforated Concrete Shear Wall)

  • 김준희;김순철
    • 전산구조공학
    • /
    • 제11권1호
    • /
    • pp.251-259
    • /
    • 1998
  • 개구부를 갖는 콘크리트 전단벽을 두께가 얇은 직사각형 평판으로 모델화하였다. 판의 두가지 경계조건에 대한 안정해석 결과를 판좌굴계수 k로 표시하였다. 경계조건이 다른 변수로는 휨으로 인한 힘/연직하중비 .alpha., 수평 전단력/연직하중비 .betha. 및 개구부의 위치 및 크기 변화이다. 유한요소법에 의한 결과를 얻기 위하여 예제의 판을 27*9의 정사각형 요소로 분할하였으며 node에서 3가지 자유도를 갖는 c.deg. 유한요소를 택하였다. 일반적으로 개구부의 크기가 증가함에 따라 판 개구부가 판 중앙에서 자유연(free edge)으로 접근할수록 좌굴계수는 감소하는 현상을 보이고 있다.

  • PDF

Nonlinear dynamic properties of dynamic shear modulus ratio and damping ratio of clay in the starting area of Xiong'an New Area

  • Song Dongsong;Liu Hongshuai
    • Earthquakes and Structures
    • /
    • 제26권2호
    • /
    • pp.97-115
    • /
    • 2024
  • In this paper, a database consisting of the dynamic shear modulus ratio and damping ratio test data of clay obtained from 406 groups of triaxial tests is constructed with the starting area of Xiong'an New Area as the research background. The aim is to study the nonlinear dynamic properties of clay in this area under cyclic loading. The study found that the effective confining pressure and plasticity index have certain influences on the dynamic shear modulus ratio and damping ratio of clay in this area. Through data analysis, it was found that there was a certain correlation between effective confining pressure and plasticity index and dynamic shear modulus ratio and damping ratio, with fitting degree values greater than 0.1263 for both. However, other physical indices such as the void ratio, natural density, water content and specific gravity have only a small effect on the dynamic shear modulus ratio and the damping ratio, with fitting degree values of less than 0.1 for all of them. This indicates that it is important to consider the influence of effective confining pressure and plasticity index when studying the nonlinear dynamic properties of clays in this area. Based on the above, prediction models for the dynamic shear modulus ratio and damping ratio in this area were constructed separately. The results showed that the model that considered the combined effect of effective confining pressure and plasticity index performed best. The predicted dynamic shear modulus ratio and damping ratio closely matched the actual curves, with approximately 88% of the data falling within ±1.3 times the measured dynamic shear modulus ratio and approximately 85.1% of the data falling within ±1.3 times the measured damping ratio. In contrast, the prediction models that considered only a single influence deviated from the actual values, particularly the model that considered only the plasticity index, which predicted the dynamic shear modulus ratio and the damping ratio within a small distribution range close to the average of the test values. When compared with existing prediction models, it was found that the predicted dynamic shear modulus ratio in this paper was slightly higher, which was due to the overall hardness of the clay in this area, leading to a slightly higher determination of the dynamic shear modulus ratio by the prediction model. Finally, for the dynamic shear modulus ratio and damping ratio of the engineering site in the starting area of Xiong'an New Area, we confirm that the prediction formulas established in this paper have high reliability and provide the applicable range of the prediction model.

화강암질풍화토(花崗岩質風化土)의 역학적(力學的) 성질(性質)에 관(關)한 연구(硏究) -전단강도(剪斷强度)의 영향요소(影響要素)와 견밀도(堅密度)에 대(對)하여- (Studies on the Mechanical Properties of Weathered Granitic Soil -On the Elements of Shear Strength and Hardness-)

  • 조희두
    • 한국산림과학회지
    • /
    • 제66권1호
    • /
    • pp.16-36
    • /
    • 1984
  • 화강암질풍화토(花崗岩質風化土)의 미교란(未攪亂) 시료(試料)를 사용하여 일면(一面) 직접(直接) 전단시험(剪斷試驗)으로 측정(測定)한 전단강도(剪斷强度)와 함수비(含水比), 간극비(間隙比), 건조밀도(乾燥密度), 비중(比重)과의 관계(關係)를 통계(統計) 분석(分析)하였고, 화강암질풍화토(花崗岩質風化土)의 사방시공지(砂防施工地)에 식재(植栽)된 리기다소나무림(林)과 리기테-다소나무림(林)에서 토양단면(土壤斷面)을 만들어 산중식토양경도계(山中式土壤硬度計)로 토양(土壤)의 견밀도(堅密度)를 측정(測定)하고 수근분포(樹根分布)를 조사(調査)하여 통계(統計) 분석(分析)한 결과(結果) 다음과 같다. 1) 함수비(含水比), 간극비(間隙比)와 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 2) 건조밀도(乾燥密度)와 전단강도(剪斷强度) 사이에는 정(正)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 3) 비중(比重)과 전단강도(剪斷强度) 간(間)에는 유의적(有意的)인 상관관계(相關關係)를 인정(認定)할 수 없었다. 4) 전단강도(剪斷强度)에 영향(影響)을 미치는 영향요소(影響要素)의 직접효과(直接效果)의 크기는 함수비(含水比)>간극비(間隙比)>건조밀도(乾燥密度)의 순위(順位)이다. 5) 다중선형(多重線型) 회귀방정식(回歸方程式)의 분산분석결과(分散分析結果) 함수비(含水比)만이 회귀성(回歸性)이 인정(認定)되므로 함수비(含水比)를 독립변수(獨立變數)로 하여 전단강도(剪斷强度)를 추정(推定)하기 위한 회귀방정식(回歸方程式)은 제한(制限)된 건조밀도(乾燥密度)의 범위내(範圍內)에서 적합도(適合度)가 매우 높게 평가(評價)되었다. 6) 토양(土壤)의 견밀도(堅密度)는 토심(土深)이 깊어짐에 따라 높아진다. 7) 토양(土壤)의 지표경도(指標硬度)와 수근수(樹根數) 간(間)에는 유의적(有意的)인 부(負)의 상관(相關)이며 직접적(直接的)인 관계(關係)에 있었다. 8) 리기다소나무와 리기테-다소나무의 수근(樹根)은 토심(土深) 20cm까지에 대부분 분포(分布)하고 있었다. 9) 리기다소나무림(林)과 리기테-다소나무림(林)에서 측정(測定)한 토양(土壤)의 지표경도(指標硬度)를 독립변수(獨立變數)로한 회귀방정식(回歸方程式)으로 수근수(樹根數)를 추정(推定)할 수 있었으나 낮은 적합도(適合度)를 나타내었다.

  • PDF

과잉간극수압 발생을 고려한 중력식 안벽구조물의 동적해석 (Dynamic Analysis of Gravity Quay Wall Considering Development of Excess Pore Pressure in Backfill Soil)

  • 유무성;황재익;김성렬
    • 한국해양공학회지
    • /
    • 제24권5호
    • /
    • pp.39-47
    • /
    • 2010
  • In this paper, a total stress analysis method for gravity quay walls is suggested. The method can evaluate the displacement of the quay walls considering the effect of excess pore pressure developed in backfill soils. This method changes the stiffness of backfill soils according to the expected magnitude of the excess pore pressure. For practical application, evaluation methods are suggested for determining the excess pore pressure ratio developed in the backfill soils and the backfill stiffness that corresponds to the excess pore pressure ratio. This method is important in practical applications because the displacement of the quay walls can be evaluated by using only the basic input properties in the total stress analysis. The applicability of the suggested method was verified by comparing the results of the analysis with the results of 1-g shaking table tests. From the comparison, it was found that the calculated displacements from the suggested method showed good agreement with the measured displacements of the quay walls. It was also found that the excess pore pressure in backfill soils is a governing influence on the dynamic behavior of quay walls.

고강도 콘크리트를 사용한 플랫 플레이트 구조의 기둥·슬래브 접합부 구조성능 (Structural Performance of Column-Slab Connection in Flat Plate System Using High Strength Concrete)

  • 김형기
    • 한국구조물진단유지관리공학회 논문집
    • /
    • 제10권1호
    • /
    • pp.97-105
    • /
    • 2006
  • 플랫 플레이트 구조에서 고강도 콘크리트를 사용함에 따라서 접합부의 전단강도와 같은 구조성능을 향상시켜서 플랫 플레이트 구조의 단점을 보완하여 장점을 극대화시킬 수 있다고 판단된다. 이에 본 논문에서는 70MPa급 고강도 콘크리트를 사용한 플랫 플레이트구조의 기둥 슬래브 접합부 실험체를 제작한 후에 수직하중과 수평하중의 조합하중을 가력하여 플랫 플레이트구조의 기둥 슬래브 접합부에 대한 전단강도를 비롯한 주요한 구조성능을 평가하고자 한다. 본 연구에서의 실험변수는 슬래브의 철근비와 슬래브에 작용하는 수직하중의 비율로 하였다.

팽창재 종류 및 치환율에 따른 시멘트 페이스트의 레올로지 특성 (A Study on Rheological Properties of Cement Paste using Expansive Additives by Kind & Replacement Ratio)

  • 박춘영;강병희
    • 한국건축시공학회지
    • /
    • 제8권2호
    • /
    • pp.99-106
    • /
    • 2008
  • To improve concrete tensile strength and bending strength, New plan that have more economical and simple manufacture process is groped. By an alternative plan, chemical pre-stressed concrete is presented. In this study, we analyzed the rheological properties of cement paste with the kind and replacement ratio of k-type CSA type expansive additives that is used mainly in domestic. and we suggested that the algorithm of a mixing plan in the chemical pre-stressed concrete and from this, we presented the basic report for the right mixing plan. From the results, Flow increased more or less according to use of expansive additives. This phenomenon was observed by increasing paste amount that shows as substitution for expansive additives that specific gravity is smaller than that of cement. As linear regression a result supposing paste that mix expansive additives by Bingham plastic fluid. The shear rate and shear stress expressed high interrelationship. therefore, flow analysis of quantitative was available. The plastic viscosity following to replacement ratio of expansive additives is no change almost, the yield value is decreased in proportion to the added amount of expansive additives. Through this experiment, we could evaluate rheological properties of cement paste using the expansive additives. Hereafter by an additional experiment, we must confirm stability assessment of material separation by using the aggregate with the kind and replacement ratio of expansive additives.