• Structural Engineering and Mechanics
• /
• 제49권4호
• /
• pp.491-498
• /
• 2014

During the past years, the protection of the environment has become a major concern out passing the state frontiers to reach a planetary dimension. Depository waste sites have become a serious problem in terms of their locations and costs. On the other hand, the construction industry has a leading place in terms of quantities of waste produced from the start to the end of each construction site, by the large amounts of raw materials used and their respective consequences on the environment. The recycling of quarry wastes products, of demolished concrete, bricks and large quantities of waste resulting from the transformation of marble blocks can provide ideal solutions and advantages for the preservation of the environment, to become a supplementary source of aggregates. The main purpose of this study is to show technically the possibility of recuperating the aggregates of marble wastes as a partial substitute or total in the mortars. The aggregates used in this study is a sand of marble wastes (excess loads of sand exposed to bad weather conditions) of the quarry derived from Fil-fila marble (Skikda, east of Algeria). To achieve this work, we have studied the effect of sand substitution of marble wastes in the mortar with rates of (25, 50, 75, 100%); comparing the results obtained with reference samples (0%), the properties when the samples are fresh, and the mechanical performances of mortars at solid state (loss and gain of weight, dimensional variations). The introduction of recycled sand in the mortars gives good results and can be used as granulates.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1668-1671
• /
• 2005

Vulcanized natural rubber was pulverized using a single screw extruder in a non-cryogenic Solid Shear Extrusion process where rubber granulates were subjected to high compressive and shear stresses. The producted particles had diameters ranging from 40 to 1200$\{mu}m$. A principle used in this paper was developed in Russia. The development method for producing a polymeric material powder consists in compressing said material by shearing the material during a pressure increase and cooling. Consecutive breakdown is carried out by shearing the material during the pressure decrease and cooling.

• 연구논문집
• /
• 통권28호
• /
• pp.161-172
• /
• 1998

철강재생 공장내의 전기 용융로에서 발생된 먼지중의 아연 성분을 재생하는 공정인 Waelz 공정에서는 매년 많은 양의 slag가 발생되어진다. 표면이 유리질성인 이 slag의 물리적 특성이 매우 우수하며, 건축 현장에서 골재(모래나 자갈)의 대체물질로 사용 가능한 만큼 높은 안정성을 지니고 있다. 유럽공동체 과 제인 본 연구는 여러 종류의 slag에 대한 용출특성, 물리-화학적 특성조사 및 광물학적 특성 연구에 주안점을 두었다. 용출실험으로는 법규실험과 slag의 재사용 시나리오와 관련된 여러 주요인자에 대한 영향(pH, 산환원 전위, 용매의 화학적특성, L/S비 등)에 대하여 조사되어졌다.

• 한국균학회지
• /
• 제41권3호
• /
• pp.149-159
• /
• 2013

국내 산림에서 수집한 외생균근균(13속 42균주)을 질소원이 서로 다른 4종류의 시험배지에 접종하고 56일간 순수 배양하여 질소원 요구성과 선호도를 조사하였다. 그 결과, 일본연지그물버섯(KFRI 1224), 비단그물버섯(KFRI 1232), 끈적쓴맛그물버섯(KFRI 1383), 젖비단그물버섯(KFRI 1997), 알버섯류(KFRI 1434) 등이 질소원 요구성이 높은 것으로 조사되었다. 검은머리그물버섯(KFRI 1362)을 비롯하여 총 시험균주의 45%는 질산염보다 암모늄 형태의 무기질소원을 더 선호하였다. 반면 큰비단그물버섯(KFRI 1125)을 비롯한 총 시험균주의 36%는 질산염 형태의 무기질소원을 더 선호하였다.

• Journal of Periodontal and Implant Science
• /
• 제49권1호
• /
• pp.14-24
• /
• 2019

Purpose: To assess the influence of using different combinations of guided bone regeneration (GBR) materials on volume changes after wound closure at peri-implant dehiscence defects. Methods: In 5 pig mandibles, standardized bone defects were created and implants were centrally placed. The defects were augmented using different combinations of GBR materials: xenogeneic granulate and collagen membrane (group 1, n=10), xenogeneic granulate and alloplastic membrane (group 2, n=10), alloplastic granulates and alloplastic membrane (group 3, n=10). The horizontal thickness was assessed using cone-beam computed tomography before and after suturing. Measurements were performed at the implant shoulder (HT0) and at 1 mm (HT1) and 2mm (HT2) below. The data were statistically analysed using the Wilcoxon signed-rank test to evaluate within-group differences. Bonferroni correction was applied when calculating statistical significance between the groups. Results: The mean horizontal thickness before suturing was $2.55{\pm}0.53mm$ (group 1), $1.94{\pm}0.56mm$ (group 2), and $2.49{\pm}0.73mm$ (group 3). Post-suturing, the values were $1.47{\pm}0.31mm$ (group 1), $1.77{\pm}0.27mm$ (group 2), and $2.00{\pm}0.48mm$ (group 3). All groups demonstrated a loss of horizontal dimension. Intragroup changes exhibited significant differences in group 1 (P<0.001) and group 3 (P<0.01). Intergroup comparisons revealed statistically significant differences of the relative changes between groups 1 and 2 (P=0.033) and groups 1 and 3 (P=0.015). Conclusions: Volume change after wound closure was minimized by using an alloplastic membrane. The stability of the augmented horizontal thickness was most ensured by using this type of membrane irrespective of the bone substitute material used for membrane support.