• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.253-255
• /
• 2003

Commercially pure 1050 aluminum alloy with ultra-fine grain sizes was produced by a friction stir process. The maximum temperature in the friction stir processed zone decreased almost linearly with the tool rotation speed. In the friction stir processed zone, dislocation density was very low and fine equiaxed grains were observed. The grain size decreased with tool rotation speed. It is noteworthy that, for 560 rpm, a grain size decreased to even the submicron level with only the single pass of friction stir process. These fine grains resulted in improvement in hardness of the friction stir processed zone.

• Journal of Powder Materials
• /
• v.5 no.1
• /
• pp.22-27
• /
• 1998

The effect of the $\alpha$/$\beta$ phase fraction on the mechanical properties in silicon nitrides was investigated in part 1. In part II, we describe the role of microstructure on the mechanical properties and contact damage of silicon nitrides with coarse/equiaxed and coarse/elongated microstructures. Grain sizes and shapes were controlled by starting powder. Hertzian indentation using spherical indenter was also used to investigate contact damage behavior. Cone cracks from the spherical indentation were suppressed when the silicon nitride contains coarse and elongated grains. Coarse and elongated grains played an important role of cone crack suppression. The size of quasi-plastic zone does not depend on grain size or shape but depends on the fraction of $\alpha$/$\beta$ phase. A quasi-plastic zone was consisting of microcracks by shear stress during indentation.

• Journal of Biosystems Engineering
• /
• v.6 no.1
• /
• pp.60-72
• /
• 1981

This study was carried out to find out the effects of the sheaf size of paddy harvested by the binders on the threshing performance, load characteristics and power requirement of an auto-feed thresher. The results of the study are summarized as follows: 1. The seperating performance of the thresher appeared to be satisfactory for all the sheaf sizes although the amount of rubbishes and empty grains slightly increased with the sheaf size of paddy. 2. There was no significant difference in grain output quality of the thresher among the three sheaf sizes. However, the amount of grains left unthreshed increased with the sheaf size. In the case of the largest sheaf size with the feed rate of 780kg/h, it exceeded the limit set by the national inspection regulations. 3. The position of the feed-chain rail gave a significant effect on the power requirement of the thresher. At the feed rate of 780kg/h, the net power required to convey sheafs through the feed chain was in the range of 0.37 to 0.50 PS for the middle and lowest position of feed-chain rail, and there was no significant difference among the sheaf sizes. At the highest position, however, it appeared that the smallest sheaf required more power than the others. The net power requirements at this position were 1.03, 0.59. 0.65 PS for the smallest, medium and largest sheafs respectively. 4. The torques of both the thresher and the engine shaft increased with the feed rate and were not affected by the sheaf size for the lower two feed rates of 520 and 780kg/h. At the highest feed rate of 1,040 kg/h, however, they were affected by the sheaf size. In this case, the medium sheaf size gave lower values than the others. 5. The variations in the thresher and the engine torque increased with the feed rate and were not affected by the sheaf size for the feed rate of 520kg/h. At the feed rate of 780kg/h, however, they increased with sheaf size. And at the feed rate of 1,040 kg/h, the torque variations increased greatly for all the sheaf sizes due to an over-load operating condition. 6. It appeared that the average and maximum power requirements of the thresher increased with the feed rate. But, there was no significant difference in power requirement among the sheaf sizes for the lower two feed rates. 7. The threshing efficiency of the thresher was in the range of 214-249 kg/ps.h with the feed rates of 520 and 780 kg/h, and it was not affected by both the sheaf size and the feed rate. At the feed rate of 1,040 kg/h, however, it decreased to as low as 171-174 kg/ps.h because of a sudden increase in power requirement. 8. The average power requirements of the engine were slightly higher than those of the thresher due to the slippage of flat belt between the thresher and engine. It appeared that power transmission from the engine to the thresher was maintained properly since slippages were moderately low with the range of 2.78 to 6.51% throughout the tests. 9. The specific fuel consumption of the engine (diesel 8PS) decreased as the feed rate increased. However, there was no significant reduction in specific fuel consumption as the feed rate increased above 780 kg/h.

• Korean Journal of Community Nutrition
• /
• v.19 no.4
• /
• pp.361-371
• /
• 2014

Objectives: This study was performed to set easily applicable portion sizes by sex and age for children at the Community Child Centers (CCC) in Korea. Methods: Considering the age and gender specific energy level at Target Patterns for children aged 6-18 years, which were suggested as a part of the 2010 Korean Food Guidance System (KFGS), we set three meal sizes. We reclassified the recommended daily servings of Grains, Meat fish eggs beans and Vegetables group at Target Patterns into three meal sizes, and then calculated the recommended serving per meal. Each proposed amount of food per meal was calculated based on serving size of foods commonly eaten at KFGS, which was then allocated to five meal components; rice, soup stew, protein and vegetable side-dishes and Kimchi. Each proposed amount of food per meal was applied to 173 menus' recipes from CANpro 3.0 as main ingredient's amounts. We cooked the 173 menus at the medium size and measured their weights after cooking. Results: Each recommended serving per meal was 0.75, 0.9 and 1.2 for Grains; 1.2, 1.6 and 2.4 for Meat fish eggs beans; 2, 2.4 and 2.8 for Vegetables by meal sizes. Among five meal components, the ratio of small and large to medium size was 1/5 less and 1/3 more for rice and 1/3 less and 1/3 more for soup stew, protein side-dish and Kimchi, respectively. We suggested the same amount for a vegetable side-dish to encourage vegetable intake. Proper portion sizes per meal of medium were rice 190 g, soup stew 210 g (solid ingredients 60 g), protein side-dish 100 g (meat eggs beans) and 70 g (fish), vegetable side-dish 80g and Kimchi 30 g. Conclusions: Proper portion size per meal suggested in this study may be useful at the CCC where dietitians are not available and the approach could be applicable to the other types of meal services.

• The Korean Journal of Ceramics
• /
• v.1 no.4
• /
• pp.214-218
• /
• 1995

Partially stabilized zironia with magnesia (Mg-PSZ) is known as one of the toughest monolithic ceramics. However, the very large grain sizes obtained after sintering at a high solution-heat treatment temperature in the cubic region of the phase diagram limit the strength of this material rather modest. In this study fine-grained Mg-PSZ materials were fabricated by adding TiC particles as a dispersed phase. Samples were hot-pressed at $1750^{\circ}C$ and then annealed at $1420^{\circ}C$ for various times. Grain growth was retarded severely by the TiC particles resulting in grain sizes smaller by more than one order of magnitude than those of PSZ without TiC. The fine-grained microstructure lead to doubly-increased fracture strength while maintaining the same level of high fracture toughness as that of conventional Mg-PSZ without TiC particles.

• Korean Journal of Materials Research
• /
• v.24 no.11
• /
• pp.585-590
• /
• 2014

Microstructural evolution in the thickness direction of an oxygen free copper processed by accumulative rollbonding (ARB) is investigated by electron back scatter diffraction (EBSD) measurement. For the ARB, two copper alloy sheets 1 mm thick, 30 mm wide and 300 mm long are first degreased and wire-brushed for sound bonding. The sheets are then stacked and roll-bonded by about 50% reduction rolling without lubrication at an ambient temperature. The bonded sheet is then cut to the two pieces of the same dimensions and the same procedure was repeated on the sheets up to eight cycles. The specimen after 1 cycle showed inhomogeneous microstructure in the thickness direction so that the grains near the surface were finer than those near the center. This inhomogeneity decreased with an increasing number of ARB cycles, and the grain sizes of the specimens after 3 cycles were almost identical. In addition, the aspect ratio of the grains decreased with an increasing number of ARB cycles due to the subdivision of the grains by shear deformation. The fraction of grains with high angle grain boundaries also increased with continuing process of the ARB so that it was higher than that of the low angle grain boundaries in specimens after 3 cycles. A discontinuous dynamic recrystallization occurred partially in specimens after 5 cycles.

• Laser Solutions
• /
• v.11 no.2
• /
• pp.15-19
• /
• 2008

Electron beam (EB) weldability of pure grade Nb sheet was studied. One of Nb sheets was as-annealed and the other was cold rolled. Microstructures, Vickers hardness, and transverse weld tensile test were carried out for the base metal, the heat affected zone (HAZ) and weld metal. In the case of the EB welds made using the annealed Nb sheeet, fine equiaxed grains and coarse grains were dominant at the base metal and the HAZ, respectively, and columnar grains were observed at the weld metal. For the EB welds made using the cold rolled Nb sheet, elongated grains in the rolling direction at the base metal, and the microstructures of the weld metal and the HAZ are similar to those of the EB welds made using the annealed Nb sheet, respectively. For both annealed and cold rolled Nb sheet, the width of the HAZs are unusually wide in spite of using high density heat source, i.e. electron beam, and the grain sizes of both HAZs are similar. When tensile test was carried out using the transverse weld specimens, the failure occurred at the HAZ for both EB welds made using Nb sheets annealed and cold rolled, respectively and the tensile strengths of both specimens were 161MPa. Vickers hardness of EB welds made using annealed Nb was 56-57 Hv at both base metal and weld metal, 52-53 Hv at the HAZ. On the other hand, Vickers hardness of EB welds made using cold rolled Nb was 97-99 Hv at the base metal, but the hardness values of weld metal were similar to those obtained at the weld metal of annealed Nb.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.506-510
• /
• 2017

One of the characteristics of polycrystalline graphene that determines its material properties is grain size. Mechanical properties such as Young's modulus, yield strain and tensile strength depend on the grain size and show a reverse Hall-Petch effect at small grain size limit for some properties under certain conditions. While there is agreement on the grain size effect for Young's modulus and yield strain, certain MD simulations have led to disagreement for tensile strength. Song et al. showed a decreasing behavior for tensile strength, that is, a pseudo Hall-Petch effect for the small grain size domain up to 5 nm. On the other hand, Sha et al. showed an increasing behavior, a reverse Hall-Petch effect, for grain size domain up to 10 nm. Mortazavi et al. also showed results similar to those of Sha et al. We suspect that the main difference of these two inconsistent results is due to the different modeling. The modeling of polycrystalline graphene with regular size and (hexagonal) shape shows the pseudo Hall-Petch effect, while the modeling with random size and shape shows the reverse Hall-Petch effect. Therefore, this study is conducted to confirm that different modeling is the main reason for the different behavior of tensile strength of the polycrystalline structures. We conducted MD simulations with models derived from the Voronoi tessellation for two types of grain size distributions. One type is grains of relatively similar sizes; the other is grains of random sizes. We found that the pseudo Hall-Petch effect and the reverse Hall-Petch effect of tensile strength were consistently shown for the two different models. We suspect that this result comes from the different crack paths, which are related to the grain patterns in the models.

• Journal of Powder Materials
• /
• v.30 no.3
• /
• pp.242-248
• /
• 2023

The Ag/WC electrical contacts were prepared via powder metallurgy using 60 wt% Ag, 40 wt% WC, and small amounts of Co₃O₄ with varying WC particle sizes. After the fabrication of the contact materials, microstructure observations confirmed that WC-1 had an average grain size (AGS) of 0.27 ㎛, and WC-2 had an AGS of 0.35 ㎛. The Ag matrix in WC-1 formed fine grains, whereas a significantly larger and continuous growth of the Ag matrix was observed in WC-2. This indicates the different flow behaviors of liquid Ag during the sintering process owing to the different WC sizes. The electrical conductivities of WC-1 and WC-2 were 47.8% and 60.4%, respectively, and had a significant influence on the Ag matrix. In particular, WC-2 exhibited extremely high electrical conductivity owing to its large and continuous Ag-grain matrix. The yield strengths of WC-1 and WC-2 after compression tests were 349.9 MPa and 280.7 MPa, respectively. The high yield strength of WC-1 can be attributed to the Hall-Petch effect, whereas the low yield strength of WC-2 can be explained by the high fraction of high-angle boundaries (HAB) between the WC grains. Furthermore, the relationships between the microstructure, electrical/mechanical properties, and deformation mechanisms were evaluated.

• Journal of Pharmaceutical Investigation
• /
• v.2 no.1
• /
• pp.5-13
• /
• 1972

There are some repels in which they studied on the change of acid-consuming capacity of aluminium hydroxide resulted from the passing of time. However, the relationship between grain sizes(particle sizes) and the acid-consuming capacity of dried aluminium hydroxide gel was not been studied. And studies on the grain sizes of aluminium hydroxide gel qualified by pharmacopoeia of Korea has not been reported. For the purpose of studying these two problems, the author prepared two-kinds of aluminium hydroxide gel as follows : $Na_2OAl_2O_3+CO_2------{\longrightarrow}Al(OH)_3{\cdots}{\cdots}{\cdots}$sample 1 $Al_2(SO_4)_318H_2O+6NaHCO_3{\longrightarrow}Al(OH)_3{\cdots}{\cdots}{\cdots}$sample 2 Both of sample 1 and 2 are found to be amorphous by X-ray diffraction methods, and their acid-consuming capacities were determined by the method of pharmacopeia of Korea. The grain size was measured by X-ray diffraction method, the particle sizes observed by electron microscopy, and the change of acid-consuming capacity with passing of time was determined by the method of pharmacopoeia of Korea. The results of these studies are summerized as follows: 1. The grain size was linearly enlarged as the time goes by. The aluminium hydroxide gel gradually crystallized in a certain period of time. 2. The acid-consuming capacity was in exponential function, decreased as the grain size of them enlarged. 3. One particle consists of tens of grains.4. Grinding the Sample obtained in any period of testing time in mortar did not change both their grain size and their acid-consuming capacity. 5. The grain size of dried aluminium hydroxide gel ought to be micronized less than $100{\AA}$ for maintaining the ability such as consumes 250m1 of 0. 1N-HC1 solution per Is of $Al(OH)_3$ described in pharmacopoeia of Korea.