• 한국농공학회지
• /
• 제16권4호
• /
• pp.3600-3610
• /
• 1974

Experimental work of batch-type dryer was conducted to develop its optimurm operating conditions by analyzing the major factors which affect the drying performance. A laboratory batch-type dryer was constructed and tested for various levels of heated-air rates, and depths of grain deposit. Tong-il rice variety having the initial moisture content of approximaely 23 per cent in wet basis was used for the experiment. The criteria selected for establishing the optimum operating condition were the drying performance rate, the thermal efficiency, and the operational cost of the dryer. The results of the study are summarized as follows: 1. The performance rate of dryer for a specific operating condition was defined as total amount of material dried per hour when the moisture content of grains in the upperlayer reaches to 16 per cent in wet basis. The optimum operating conditions as viewed in the rate of drying performance could be justified by functional realtionship between the depth of grain deposit and air flow rate. In other words, there was a definite depth of grain deposit for a given air-rate which make the dryer performance maximum. The optimum grain depth for the batch-type dryer with 3.3㎡ loading area and with the attached axial fan was about 35cm. 2. The thermal efficiency for the dryer was evaluated by the ratio of the latent heat required to evaporate the grain moisture to the heat input required to raise the ambient air-temperature to 40 degree centigrade. The optimum operating condition as viewed in term of thermal efficiency analyzed was that grater depth and lower air flow-rate may be desirable. This condition is contracted with the optimum condition as viewed by the dryer performance rate. 3. The annual operating cost of batch-type dryer was analyzed for different annual hour of use and for different operation condition. The optimum condition as viewed in terms of operating cost was almost identical to one as viewed in terms of dryer performance rate. Therefore, the most economical use of batch-type dryer for the same annual operating hours can be obtained when the dryer operated in the condition of maximum dryer performance rate. Increasing the annual operating hour may be desirable to cut down the dryer operation cost, since the annual hour of dryer use is much sensitive to the operating cost than any peractical conditions of dryer operation. 4. The most desirable operational condition as justified by combining all the criteria, dryer performance rate, thermal efficiency and annual operating cost, could be concluded to operate the dryer in the condition of maximum performance rate. The condition in general is identical to the lowest operation cost for a given annual operating hour.

• 소성∙가공
• /
• 제9권4호
• /
• pp.389-394
• /
• 2000

The studies on gram size refinement for rheocast processing of hypereutectic Al-18%Si alloys have been investigated in the present study. To increase the efficiency of mechanical stirring, sieve type stirrer are newly designed and implemented for rheocasting of hypereutectic Al-18%Si alloy. Mechanical stirring of semi-solid slurry by using sieve type mechanical stirrer results in morphological changes of the primary Si particles, from angular rod shape to near spherical shape and uniform distribution of proeutectic Si. The remarkable spheroidization of Primary Si Particles and distributional uniformity of proeutectic Si show well the efficiency of sieve type mechanical stirring method which can accelerate the coalescence-fracture-wear of the individual particles by strong turbulent flow between lattices during rotation of sieve type stirrer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.85-89
• /
• 1997

A microstructure of realistic ZnO varistor was constructed by Voronoi network and studied cia computer simulation. The grain size and standard deviation was calculated with new method and have good agreement with experimental data. In this network, the grain boundary conditions of three different type are randomly distributed. The three electrical boundary conditions . (1) type A junctions (high nonlinearity); (2) type B junctions (low nonlinearity); (3) type C junctions (linear with low-resistivity) are fitted from the experimental measurement. The electrical properties were studied by varying the boundary type concentration and the disorder parameter d. The shape of I-V characteristic curve of the network is affected by the type concentration and the disorder parameter has an effect on the double inflected region.

• 암석학회지
• /
• 제3권1호
• /
• pp.20-33
• /
• 1994

Some of the seven types of subgrain boundaries (Means and Ree, 1988) in octachloropropane samples show distinctive deformation patterns during their development. Type II subgrain boundaries migrate to accommodate the deformation difference between adjacent grains. The formation of Type III requires a rigid-body roation of grains to reduce misorientation of adjacent grains. Type I, IV, V and VI develop either in static or dynamic condition. Type VII form only in static environments after deformation. Ribbon grains can develop via Type III or Type IV process. The orientation pattern and density of subgrain boundaries are more or less stable through a post-deformation heating. Subgrain boundary orientations are symmetric with respect to the grain-shape foliation in pure shear. In simple shear, their maximum inclines toward the direction of shear.

• Journal of Biosystems Engineering
• /
• 제11권2호
• /
• pp.55-65
• /
• 1986

The resistance to the passage of airflow through various agricultural products is an important consideration in the design of an aeration or drying system. The amount of resistance to airflow varied widely from one kind of grain to another, and depended upon airflow rate, surface texture and shape of the particles, the size and configuration of voids, and foreign and fine material in the grain bed. The airflow rate was the major factor considered on this kind of study in the early stages. But these days, the studies on the resistance to airflow of grain affected by grain moisture content and foreign and fine material have been widely carried out. However the foreign an fine material in the grain bed could not be a major factor on the study in Korea because there were only a few grain process procedure after harvesting it. The objectives of this study were to investigate the effect of moisture content and airflow rate on airflow resistance to grain, and to develop a model to predict the static pressure drop across the grain bed as a function of moisture content and airflow rate. The rough rice varieties, Akibare, Milyang 15 (Japonica types), Samkwang, Backyang (Indica types)and covered barley variety, Olbori, which were harvested in 1985 were used in the experiment after cleaning them. Resistances to airflow of grain were investigated at four levels of moisture content (13-25%, wb.) for ten different airflow rates($0.01-0.15m^3/sm^2$). The results of this study are summarized as follows; 1. Theaverage bulk densities were $585.3kg/m^3$ for rough rice and $691.6kg/m^3$ for barley at the loose fill, and were $648.8kg/m^3$ for rough rice and $758.2kg/m^3$ for barley at the packed fill. The pressure drops at the packed fill beds were approximately 1.4 to 1.8 times higher than those at the loose fill beds. 2. The pressure drops across grain beds deceased with the increase of moisture content and increased with airflow rate. The decreasing rates of pressure drop across grain beds according to the moisture contents at the lower airflow rates were higher than those at the higher airflow rates, and the increasing rates of pressure drop according to the airflow rates at the lower moisture contents were higher those at higher moisture contents. 3. The pressure drop across barley bed were much higher than rough rice beds and the pressure drops across Japonica type rough rice beds were a little higher than Indica type. 4. The mathematical models to predict the pressure drop across grain beds as a function of moisture content and airflow rate were developed from these experiments.

• 한국작물학회지
• /
• 제30권2호
• /
• pp.158-164
• /
• 1985

참깨 후기등숙 불량을 개성하기 위한 기초연구로서 각 초형별 삭과와 종실의 상육과정을 조사·비교한 결과 다음과 같은 결론을 얻었다. 1. 삭장은 수정 직후부터 신장을 시작하여 수정후 35 일에 최대를 기록한 후 점차 감소하였다. 2. 상위삭의 삭장은 중·하위등에 비하여 짧아 발육이 부진하였으며, 4실8방 형은 2실4방 형보다 상위삭의 발육이 더욱 불량하였으나 BTB (분지, 3,2/4) 형은 타 초형에 비하여 상위삭의 발육이 양호한 편이었다. 3. 삭의 착생 위치에 따른 발육은 주경 중심삭>분지 중심삭 >주경 측삭 >분지 측삭의 순으로 좋았다. 4. 삭폭은 삭장에서와 같이 수정 후 35 일에 최대를 기록하다가 이 시기를 정점으로 점차 감소하였으며 삭의 발육은 착삭 하위부>중위부>상위부의 순으로 양호하였다. 5. 3과성 4실 8방형에서는 상위삭폭이 생식생장 후기에 큰 폭으로 떨어져 등숙면에서 불리하였으며 삭장에서와 같은 경향이었다. 6. 생체 천립중에서도 수정 후 35 일에 최대를 기록한 후 점차 감소하는 경향이었으며 착삭 하위부>중위부>상위부의 순으로 발육이 양호하였다. 7. 천립중에서도 분지삭과 측삭은 중심삭보다도 발육이 떨어졌으며 4실8방 형은 삭폭이나 삭장에서와같이 생식생장 후기 상위삭의 천립중 감소가 심하였다. 8. BTB(분지, 3,2/4) 형은 가장 많은 sink를 보유하였음에도 중·하위부삭에 대비한 상위부삭의 천립중 감소가 많지 않아 등숙과 증수 측면에서 유리하였으며 수량성을 극대화하기 위해서는 BTB와 같은 초형에 분지삭과 측삭의 충실도를 높이는 방향의 육종이 바람직하다 하겠다.

• 한국세라믹학회지
• /
• 제33권6호
• /
• pp.718-724
• /
• 1996

Deformation mechanism map of Langdon-Mohammed type for YBa2Cu3O7-x superconducting ceramic was constructed by considering mechanisms of Nabarro-Herring Coble and powder-law creep and grain boundary sliding (GBS) with an accommodation by grain boundary diffusion. The map was found consistent with experi-mental results not only of the creep the also of the superplastic deformation. It showed the transition from interface reaction-controlled to the grain boundary diffusion-controlled GBS mechanism at about 1 ${\mu}{\textrm}{m}$ grain size and 100 MPa flow stress in agreement with the experimental results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.597-600
• /
• 1999

A solar cell conversion efficiency was degraded by grain boundary effect in polycrystalline silicon To reduce grain boundary effect, we performed a preferential grain boundary etching, POC$_3$ n-type emitter doping, and then ITO film growth on poly- Si. Among the various preferential etchants, Schimmel etch solution exhibited the best result having grain boundary etch depth higher than 10 ${\mu}{\textrm}{m}$. RF magnetron sputter grown ITO films showed a low resistivity of 10$^{-4}$ $\Omega$ -cm and high transmittance of 85 %. With well fabricated poly-Si solar cells, we were able to achieve as high as 15 % conversion efficiency at the input power of 20 mW/$\textrm{cm}^2$.

• 한국주조공학회지
• /
• 제3권3호
• /
• pp.167-173
• /
• 1983

The effect of sand grain size on the various properties of mold is not only basic but important interest which we have to deal with.And the relation among the various properties of mold (strength, permeability, flowability, compactability, hardness, deformation, toughness etc.) is very complicated and inaccurate, so we can delineate the behavior of mixture (sand+water+bentonite) with experience only. Within recent years a so-called rigid-water theory has been accepted as a means of advancing logical explanations for the research aimed at delineating sand-clay-water relationships. By changing grain size or mesh no. of grain, specimens have been subjected to green compressive strength, permeability, deformation, flowability, compactablity, toughness at room temperature. Under constant mulling energy and ratio of water/bentonite, the results obtained were as follows: 1. With decreasing grain size green compressive strength of the specimen increased. 2. With decreasing grain size permeability decreased. 3. With decreasing grain size flowability and bulk density decreased but compactability increased. 4. With decreasing grain size deformation decreased but toughness increased. 5. At 60 mesh no., the properties of specimen are conspicuously changed. The reason is that the total surface area of sand grain which affects the type of bonding between sand grains is more changed at 60 mesh number.

• 한국농림기상학회지
• /
• 제8권3호
• /
• pp.183-189
• /
• 2006

건물 생산 및 수량 관련 특성들을 비교 검토하고자, 시대별로 보급 면적이 넓었던 Japonica 6품종과 통일형 3품종에 대하여 건물 생산 특성인 광소멸계수(K), 광이용효율(RUE), 누적엽면적지수(LAD) 등과 수량 및 수량구성요소를 조사하였고, 각 특성들을 비교 검토하였다. 벼 군락의 K는 70년대 이전에 보급된 품종은 0.5이상으로 높은 값을 보였으나, 그 이후에 나온 Japonica 품종과 통일형 품종은 0.5보다 낮은 값을 보였다. 출수전 RUE는 japonica 품종 중에서는 팔달벼가 가장 낮았고, 조동지와 낙동벼가 높았으며, 통일형 품종 중에서는 밀양23호가 유의하게 낮았으나 품종육성연대에 따른 일정한 변화경향은 없었다. 한편 등숙기 RUE는 품종간에 유의적인 차이가 없었다. LAD는 품종간에 유의적인 차이가 있었는데, 최근에 육성된 품종일수록 LAD가 큰 경향이었다. 출수기까지의 LAD는 출수기 건물중과 유의한 상관이 인정되지 않았으나, 출수 후 LAD 및 전 생육기간의 LAD는 등숙기 건물생산량 및 수확기 건물중과 각각 유의한 정의 상관이 있었다. 출수기 및 수확기 건물중은 품종간에 유의적인 차이는 없었으나 통일계 품종의 경우는 최근에 육성된 품종일수록 높은 경향이었다. 수량은 자포니카 품종의 경우 1900년대 이전 품종인 조동지만이 유의하게 수량이 낮았으며, 그 이후에 육성된 japonica 품종 간에는 수량의 차이는 없었다. 통일형 품종은 최근에 육성된 품종일수록 수량이 높은 경향이었다, 수량은 단위면적당 영화수와 유의한 정의 상관관계가 있었는데 통일계 품종은 최근에 육성된 품종일수록 단위면적당 영화수가 많았다. 이상의 결과를 요약하면 japonica 품종의 경우 육성보급 연대에 따른 건물생산 특성인 K, RUE 및 LAD의 일정한 변화 경향이 없었으나, 통일계 품종의 경우는 최근에 육성된 품종일수록 수량이 증가하였는데, 이는 영화수 증대에 따른 sink size 증대와 더불어 LAD증대에 따른 건물생산성 증대에 기인하는 것이었다.