• 소성∙가공
• /
• 제13권8호
• /
• pp.704-709
• /
• 2004

The effect of annealing temperature on microstructures and mechanical properties of the 5052 Al sheets rolled 88% reduction at cryogenic temperature was investigated for the annealing temperature of 150 ~ $300^{\circ}C$, in comparison with those rolled at room temperature. The presence of equiaxed grains, whose size is about 200nm in a diameter, was observed in the alloy deformed 88% and annealed $200^{\circ}C$ for an hour. When compared with the deformation at room temperature, the deformation at cryogenic temperature showed the higher strengths and equivalent elongation after annealing at the annealing temperature below $200^{\circ}C$. However, for annealing above $250^{\circ}C$ materials deformed at cryogenic temperature showed the lower strength than those deformed at room temperature. This behavior might be attributed to the higher rate of recrystallization and growth in materials deformed at cryogenic temperature during annealing, due to the lager density of dislocations accumulated during the deformation.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.812-813
• /
• 2006

Dimensional change of compact made from (Fe-Cu) prealloyed powder and copper powder compared to that of compact made from iron-copper elemental powder. The compact made from the prealloyed powder with a copper content of 7.18mass% which is nearly equal to its solution limit and copper powder showed only the large contraction in spite of penetration of liquid copper into grain boundary of the prealloyed powder. But the compact made from iron-copper elemental powder showed the large expansion in spite of same chemical composition with former case.

• 대한기계학회논문집
• /
• 제12권6호
• /
• pp.1320-1326
• /
• 1988

본 연구에서는 파괴역학적인 해석법과 표면레프리카법을 확장, 적용시켜 피로 -크리프하의 유지시간에 따른 작은 표면균열의 분포상태와 이의 합체, 성장 및 밀도변 화특성을 해석하여 기초적 자료를 얻는다.

• 한국세라믹학회지
• /
• 제20권2호
• /
• pp.115-122
• /
• 1983

There has been many controversies about the effects of additive in sintering of SiC But no prior systematic work has been reported about the difference between the effects of B and $B_4C$ as additive. The sintering behavior of SiC and its strength are studied and the optimum concentrations of additives and sintering conditions for SiC are determined. The effects of B and $B_4C$ have same effects on reactive sintering of SiC except the easiness of transport via vapor phase for uniform distribution in case of B. The strength of sintered SiC without exaggerated grain growth is limited by surface flaws and is nearly independent of temperature up to 140$0^{\circ}C$.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권2호
• /
• pp.97-100
• /
• 1998

We have investigated the effects of crystalline activation on solid phase crystallization (SPC) of amorphous silicon (a-Si) thin films. Wet blasting and self ion implantation were employed as the activation treatments to induce macro or micro crystalline damages on deposited a-Si films. Low temperature and larger grain crystallization were obtained by the applied two-step activation. High degree of crystallinity was also observed on both furnace and rapid SPC. crystalline activations showed the promotion of nucleation on the activated regions and the retardation of growth in an amorphous matrix in SPC. The observed behavior of two-step SPC was strongly dependent on the applied activation and annealing processes. It was also found that the diversified effects by macro and micro activations on the SPC were virtually diminished as the annealing temperature increased.

• 한국전기전자재료학회논문지
• /
• 제35권4호
• /
• pp.322-332
• /
• 2022

Energy storage capacitors based on dielectric ceramics with superior polarization properties and dielectric constant can provide much higher output power density due to their very fast energy charging/discharging rates, which are particularly suitable for operating pulsed-power devices. For an outstanding energy storage performance of dielectric capacitor, a large recoverable energy density could be derived by introducing a slim polarization-electric field hysteresis loop into dielectric materials by various technical approaches. Many research teams have explored various dielectric capacitor technologies to demonstrate high output power density and ultrafast charging/discharging behavior. This article reviews the recent research progress in high-performance dielectric capacitors for pulsed-power electronic applications.

• 한국세라믹학회지
• /
• 제35권3호
• /
• pp.287-293
• /
• 1998

The effects of B2O3 addition on the sintering behavior and th microwave dielectric properties of $(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics were investigated. By addition of $B_2O_3$, increases the density of the ceramics increases and grain growth enhances, It was densified to over 94% of $(Mg_{0.93}Ca_{0.07})TiO_3$ theoretical density by the addition of 0.15-1.0wt% B2O3 and stable microwave dielectric properties observed by the addition of 0.2-0.4wt% $B_2O_3.\;(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics sintered at $1200^{\circ}C$ exhibits maximum dielectric constants of 24-25 quality factor($Q{\times}f$) of more than 70000 and temperature coefficient of resonant frequency of $0\;ppm/^{\circ}C$ by adding of 0.15-0.4wt% $B_2O_3$.

• 열처리공학회지
• /
• 제21권6호
• /
• pp.287-292
• /
• 2008

Dissolution behavior of complex carbonitrides in a Nb-Ti-V microalloyed steel was quantitatively examined by electrical resistivity, transmission electron microscopy (TEM), and optical microscopy. The electrical resistivity increased with solution treatment temperature up to $1250^{\circ}C$ for a holding time of 15 min. But, an increasing rate of electrical resistivity with temperature was obviously decreased above $1150^{\circ}C$. As the solution treatment temperature increases, irregular shaped Nb-rich carbonitrides disappear and cuboidal Ti-rich carbonitrides are observed. Abnormal grain growth occurs above $1250^{\circ}C$ for a holding time of 15 min. The optimal solution treatment temperature of a Nb-Ti-V microalloyed steel was determined as $1200^{\circ}C$ for a holding time of 15 min.

• 한국세라믹학회지
• /
• 제38권12호
• /
• pp.1080-1084
• /
• 2001

Alumina-based nanocomposites have improved mechanical properties such as hardness, fracture toughness and fracture strength compared to monolithic ceramics. In this study, alumina with 5 vol% of nanosized SiC was sintered by a hot pressing technique at 1600$\^{C}$, 30 MPa for 1h in an argon gas atmosphere. Microstructures and mechanical properties in alumina-SiC nanocomposite were investigated. Moreover, tribological properties in air and water were compared each other. Relationships of wear properties with mechanical properties such as hardness, strength, and fracture toughness as well as microstructure were studied. Based on experimental results it was found that nanosized SiC retarded grain growth of matrix alumina. Mechanical properties such as hardness, fracture toughness and strength were improved by the addition of nanosized SiC in alumina. Improved mechanical properties resulted in increased sliding wear resistance. Tribological behavior of nanocomposites in water seemed to be governed by abrasive wear.

• 한국안전학회지
• /
• 제12권2호
• /
• pp.45-56
• /
• 1997

Fracture behavior of ex-serviced 1Cr-0.5Mo steel was measured at room($24^{\circ}C$) and elevated($538^{\circ}C$) temperature and compared with that measured with virgin 1Cr-0.5Mo steel. Compact C(T) specimens were machined from the base and welded test materials. In case of the C(T) specimens of the weld, fatigue precrack was introduced along the fusion line so that following crack growth should occurs along the region of heat affected zone. It was observed that the J-R curve of the serviced material was significantly lower than that of the virgin material at room temperature. Brittle fracture was observed in the serviced material. On the other hand, at elevated temperature no noticeable difference was found between the J-R curves of the virgin and the serviced material. The measured J-R curves were also compared with those of the 1.25Cr-0.5Mo steel obtained from the other literatures. Optical microscopy and SEM examination of the serviced material reveal the carbide in/along the grain boundary which shows material degradation due to long-term usage. An example of application of the measured J-R curves is shown.