• 한국세라믹학회지
• /
• 제30권6호
• /
• pp.449-456
• /
• 1993

Sintering behaviour of zirconia powders prepared by different processing treatment was discussed. About >99% densities of theoretical were obtaiend on sintering at 140$0^{\circ}C$ for 2h in case of 300MPa uniaxially cold-pressed compact. But the lower densities were obtained on sintering above this temperature due to abnormal grain growth enabling the tetragonal to monoclinic phase transformation during cooling resulted in microcracks. All kinds of different dried powders exhibited nearly the same shrinkage behaviour with end-point shrinkage between 19 and 20%, and had maximum shrinkage rate (0.99~1.27%/min) around 120$0^{\circ}C$. During whole sintering process densification was mainly governed by grain growth and rearrangement of agglomerates. Heterogeneous abnormal grain growth and abrupt decrease in shrinkage were observed when continuous interagglomerate pore collapsed into isolated pores.

• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.567-574
• /
• 1995

The effect of MnO2 addition to 0.1mol% Sb2O3-doped BaTiO3 ceramics on microstructure and PTCR characteristics was studied. The PTCR characteristics was observed when 0.01 and 0.02 wt% MnO2 were added and sintered at 132$0^{\circ}C$ for 1 hour. The characteristics can be explained by the changes in the number and size of the abnormal grain growth due to the liquid phase during sintering. when the amount of MnO2 addition was 0.03 wt%, the sample showed NTCR characteristics with room-temperature resistivity over 109 Ωm regardless of the sintering temperature. This behavior can be described by the microstructure change due to the abnormal grain growth and charge compensation effect by MnO2 added. The room-temperature resistivity was increased as the amount of MnO2 was increased. And the specific resistivity ratio (pmax/pmin) showed maximum at 0.02wt% MnO2.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.38-38
• /
• 2010

Ever since the experimental discovery of graphene exfoiliated from the graphite flakes by Geim et at., this area has drawn a lot of attention for its possible application in IT industry. For the growth of graphene, chemical vapor deposition (CVD) has been widely used to fabricate the large area graphene. The lateral size of this graphene can be easily controlled by the size of the metal substrate though the chemical etching to remove this substrate is somewhat troublesome. Another problem which is hard to avoid is the folding at the grain boundary. We will discuss the origin of the folding first and introduce the way to avoid this folding. To solve this problem, we have used the various types of micro-thin metal foils. The precise control of hydro-carbon and the carrier gas results in the formation of the graphene on top of substrate. The thickness of graphene layers can be controlled with the control of gas flow on top of Cu substrate in contrast to the previously reported self-limiting growth $behavior^1$. Uniformity of this graphene layer has been checked by micro-raman spectroscopy and SEM. The size of grain can be enhanced by thermal treatment or use of other metal substrate. The dependence of grain size on the lattice size of the substrate will be discussed. By selecting the shape of substrate, we can grow various types of graphene. We will introduce the micron size graphene tube and its application.

• 한국세라믹학회지
• /
• 제27권1호
• /
• pp.7-12
• /
• 1990

The influence of MnO2 on the sintering property and PTCR behavior of(Ba0.8Sr0.2)TiO2 has been investigated. And the densities, grain sizes and electrical resitivities of specimens were measured as a function of doping with Mn ion of varying concentration. The density and grain size of the sintered specimens were almost the same regardless of MnO2 addition up to 0.2mol% MnO2. But in the case of 0.25mol% MnO2 addition, abnormal grain growth was appeared. So the grain size distribution was wide and density decreased greatly. The room-temperature resistivity increased as Mn content increased and the temperature coefficient of resistivity was highest in the case of 0.15mol% MnO2 addition.

• 한국정밀공학회지
• /
• 제14권7호
• /
• pp.82-90
• /
• 1997

When a structure is made by the process of forging, it has the different mechanical properties from those it has before the process. This study is based on the crack closure phenomenon of the crack growth behavior of forged AI7050-T7452. The specimens were prepared in three kinds of forging ratio in order to find out the effects of crack closure on the forged material and compare the crack growth behavior with not-forged aluminum. COD method and strain gage method were used in measuring the crack closure stress and the results from those methods were compared each other. FEM analysis was applied to verify the effective stress intensity factor range by the superposition of the crack closure load to the crack tip. In the result of this study, the crack closure stress decreased with increasing the forging ratio due to the finer grain size and the brittle manner.

• 한국세라믹학회지
• /
• 제48권4호
• /
• pp.323-327
• /
• 2011

The effects of $Dy_2O_3$ and $Er_2O_3$ co-doping on electrical properties and temperature stability of barium titanate ($BaTiO_3$) ceramics were investigated in terms of microstructure and structural analysis. The dielectric constant and the insulation resistance (IR) of 0.7 mol% $Dy_2O_3$ and 0.3 mol% $Er_2O_3$ co-doped dielectrics had about 60% and 20% higher than the values of undoped one, respectively, and the temperature coefficient of capacitance (TCC) met the X7R specification. The addition of $Dy_2O_3$ contributed to electrical properties caused by increase of tetragonality; however, preferential diffusion of $Dy^{3+}$ ions toward A site in $BaTiO_3$ grain exhibited an adverse effect on temperature stability by grain growth. On the other hand, The $Er_2O_3$ addition in $BaTiO_3$ could affect the TCC behavior and the IR with suppression of grain growth caused by reinforcement of grain boundary and electrical compensation. Therefore, the enhanced electrical properties and temperature stability through the co-doping could be deduced from the increase of tetragonality and the suppression of grain growth.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 추계총회,초청강연,특별강연,연구발표회
• /
• pp.113.1-113
• /
• 2000

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2002년도 추계총회 및 연구발표회 초록집
• /
• pp.101.2-101
• /
• 2002

• 한국세라믹학회지
• /
• 제41권2호
• /
• pp.125-130
• /
• 2004

서로 다른 크기의 SiC 원료분말을 첨가한 A1$_2$O$_3$-SiC 복합재료의 미세조직과 그에 따른 기계적 물성의 변화를 관찰하였다. 0.15 $mu extrm{m}$의 SiC가 첨가된 복합재료의 경우 기지상의 입성장이 효과적으로 억제되었다 그러나, 소수의 비정상입자가 생성된 이후에는 이들 입자의 급격한 성장으로 불규칙한 형상의 커다란 입자로 구성된 미세조직을 보이며, 파괴강도값은 급격히 감소하였다. 3 $\mu\textrm{m}$의 SiC가 첨가된 경우에는 기지상의 입성장이 일어났으나, 소수의 비정상입자가 생성된 이후에는 과도한 입성장은 억제되고 일정한 크기의 비정상입자가 시편 전체에 균일하게 형성된 미세조직을 보였다. 한편, 0.15 $\mu\textrm{m}$와 3 $\mu\textrm{m}$의 SiC 입자를 동시에 첨가한 시편은 균일한 크기의 비정상입성장의 미세조직을 보였으나, 비정상입성장이 일어났음에도 불구하고 기계적 물성은 우수하게 유지되었다 즉, 비정상입성장에 의해 미세조직에는 큰 변화가 일어났으나, 파괴강도값에는 변화가 없었다.

• 한국재료학회지
• /
• 제10권1호
• /
• pp.83-89
• /
• 2000

$Si_3N_4$에 2wt% $Al_2O_3$와 6wt% $Y_2O_3$을 첨가한 분말을 가스압 소결 방법으로 시편을 제조하였다. 이때 소결시 시간변화에 따른 공기 중에서 마모 특성을 비교하였다. 소결 시간에 따른 마모 특성의 변화는 기계적 성질, 즉, 파괴인성 등이 영향을 주는 것으로 나타났다. 소결 시간이 길어지면 큰 elongated 입자의 과잉성장에 따라 곡강도 및 파괴인성이 낮아져 이 결과 마모가 증가되었다. 이때 나타난 결과에 의하면 공기 중에서 질화규소의 마모특성에 영향을 주는 인자는 여러 가지 기계적 특성 중에서 파괴인성 및 곡강도가 미치는 영향이 크게 나타났다.