• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.187-192
• /
• 1998

Generally the solidified microstructures of materials consist of the columnar and equiaxed dendritic regions, and many theoretical studies about columnar-to-equiaxed transition have been done because that is closely related to the mechanical and physical properties of products. In this study, the modified equation based on the Hunt's analytical columnar-to-equiaxed transition condition which was derived from heterogeneous nucleation and grain growth in front of the columnar dendrite tip under directional solidification, was obtained applying the growth-velocity-dependent distribution coefficient and liquidus slope to Hunt's. The effects of the number of nucleation sites, nucleation temperature, alloy composition, growth velocity and liquid temperature gradient on the transition for Al-Cu alloys have been investigated.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1102-1107
• /
• 1999

SiC-Si3N4 composites were prepared by mixing $\alpha$-Si3N4 powder to $\alpha$-SiC powder in the range of 10 to 30 vol% with 10vol% interval. 6wg% Al2O3 and 6wt% Y2O3 were respectively added as sintering aids. Hot pressing was performed at 1,80$0^{\circ}C$ for 1 hour with 25 MPa pressure. In the case of adding 20vol% of $\alpha$-Si3N4 powder the relative density to theoretical value and the flexural strength were 99.1% and 34,420 MPa respectively and the worn amount was 2.09$\times$10-3 mm2 which were the highest values in the all range of he composition. Although the composite containig 10 vol% of $\alpha$-Si3N4 powder showed the highest fracture toughness(KIC) of 4.65MN/m3/2 the reduction of the wear resistance in this composite is likely to be affected by the homogeneity and the uniformity of the grain coalescence and growth during the sintering process.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.605-609
• /
• 2004

The microstructure, electrical and dielectric characteristics of ZnO varistors were investigated at various metal oxide (NiO, MgO, and Cr$_2$O$_3$) additives. The average grain size was increased with addition of NiO while that was decreased with addition of Cr$_2$O$_3$-Thereby, the varistor voltage was higher in Cr$_2$O$_3$-added composition. Among varistors, the varistor added with Cr$_2$O$_3$ exhibited the highest nonlinearity, with 40.5 in the nonlinear exponent and 2.7 ${\mu}$A in the leakage current and its dielectric dissipation factor was relatively low value of 0.0589.

• Journal of the Korean Ceramic Society
• /
• v.13 no.3
• /
• pp.55-62
• /
• 1976

순수한 닉켈과 금 박막을 (III)규소 단 결정위에 진공 증착시켰다. Ni/Au/Si나 Au/Ni/Si시료를 진공중에서 약 55$0^{\circ}C$로 가열하였을 때 육방정 혹은 변형된 육방정의 미소 결정들이 규소 기질위에 형성되었다. 이들 미소 결정들의 형성과정 및 조성은 X-선 회절법, scanning electron microscopy 및 scanning Auger microprobe 법을 사용하여 결정하였다. 이들 미소 결정은 NiSi2임이 확인되었다. Ni/Au/Si 시료에서는 Au-Si 공융점(37$0^{\circ}C$) 이상으로 온도가 증가됨에 따라 닉켈과 규소가 Au-Si 공융체 속으로 이동한 후 반응하여 NiSi2를 형성하였다. Au/Ni/Si 시료에 있어서의 Au-Si 공융체 형성은 닉켈 박막에 있는 바늘구멍형의 표면 결함과 관련 지을 수 있겠다. 금이 닉켈 박막의 grain boundary를 통하여 Ni/Si 계면으로 확산되어 그 계면을 습윤시킨 다음 Au-Si 공융체를 형성하였다. 이런 Au-Si 공용체는 닉켈과 규소 원자에 대한 높은 확산 매질로서 작용하여 NiSi2 형성을 촉진시켰다. 표면에 평행한 (III)규소면 위의 NiSi2 미소 결정은 유사한 육방정으로 나타났으며, 경사진 미소결정은 부등변 사변형과 유사하였다. Auger 스펙트럼 및 Ni, Au 및 Si에 대한 내층조성(indepth Composition Profiles)은 NiSi2 미소 결정이 Au-Si 공융체의 matrix에 미소 부분으로 나타났음을 보여주었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.54-60
• /
• 2001

This study is to investigate the mechanical properties and the fatigue crack propagation of fire resistance steel for frame structure as the chemical composition was changed by addition of N, B and rolled end temperature was varied. We used two kinds of specimen, the one is parallel and the other is perpendicular to the rolling directions. As rolled end temperature increased, volume fraction of ferrite and pearlite decreased, but volume fraction of baintie and grain size increased. Micro-hardness decreased as rolled end temperature increased, but tensile and yield strength increased. Volume fraction of ferrite and pearlite decreased by addition of N. But volume fraction of bainite, tensile and yield strength increased. Microstructure was changed to martensite by addition of B, and tensile and yield strength increased. Fatigue life of TL direction specimen was shorter than that of LT direction specimen. There was no significant effect to fatigue crack propagation rate by addition of N and changing rolling condition, but fatigue life was increased by addition of B.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.189-189
• /
• 2016

In this study, the Al-rich AlTiSiN thin films that consisted of TiN/AlSiN nano-multilayers were deposited on the steel substrate by magnetron sputtering, and their high-temperature oxidation behavior was investigated, which has not yet been adequately studied to date. Since the oxidation behavior of the films depends sensitively on the deposition method and deposition parameters which affect their crystallinity, composition, stoichiometry, thickness, surface roughness, grain size and orientation, the oxidation studies under various conditions are imperative. AlTiSiN nano-multilayer thin films were deposited on a tool steel substrate, and their oxidation behavior of was investigated between 600 and $1000^{\circ}C$ in air. Since the amount of Al which had a high affinity for oxygen was the largest in the film, an ${\alpha}-Al_2O_3-rich$ scale formed, which provided good oxidation resistance. The outer surface scale consisted of ${\alpha}-Al_2O_3$ incoporated with a small amount of Ti, Si, and Fe. Below this outer surface scale, a thin ($Al_2O_3$, $TiO_2$, $SiO_2$)-intermixed scale formed by the inwardly diffusing oxygen. The film oxidized slower than the $TiO_2-forming$ kinetics and TiN films, but faster than ${\alpha}-Al_2O_3-forming$ kinetics. During oxidation, oxygen from the atmosphere diffused inwardly toward the reaction front, whereas nitrogen and the substrate element of iron diffused outwardly to a certain extent.

• Korean Journal of Materials Research
• /
• v.28 no.4
• /
• pp.221-226
• /
• 2018

The property changes of 18, 14, and 8K green gold alloys for jewelry are observed by adding 0.0, 3.0, and 5.0 wt% of indium (In), respectively. To check the composition of the alloys, an energy dispersive spectroscopy (EDS) analysis is conducted. Color and microstructure analysis is executed through bare-eye, macro camera, UV-VIS-NIR-colormeter, and optical microscope. The melting point, wetting angle, and hardness are measured using TGA-DTA, a wetting angle tester, and a Vickers hardness tester. The EDS analysis result demonstrates that each of the green gold alloys was manufactured with purposed contents. The color analysis result shows that the color of the alloys is similar to the color of the conventional 4 wt%-Cd 18K green gold, and the green color improves as the In content increases. The micro structure analysis result demonstrates that grain refinement improves as the amount of In increases. Enhancements in the melting point, wettability, and Vickers hardness changes appear as the In content increases and Au content decreases. The hardness is up to 260, which implies good durability. Therefore, the results suggest that the proposed 18, 14, and 8K In-added green gold alloys enhance the properties of jewelry products with regard to the green color, castability, and durability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.64-67
• /
• 2000

Element distribution analysis and degradation characteristics of the ZnO varistors fabricated at the ambient sintering-process is investigated in this study. ZnO varistors made of Matsuoka's composition were fabricated by standard ceramic techniques. The ambient sintering-process is performed at the special electrical-furnace which is equipped with the vacuum system. The Gases of injection at sintering- process were oxygen, air, nitrogen and argon respectively. Element and quantitative analysis in the microstructure of ZnO varistors made use of EPMA equipment. Degradation characteristics were showed by DC degradation tests at $115{\pm}2\;^{\circ}C$ for period up to 13 h. From above analysis, it is found that at the DC degradation test the ZnO varistor sintered in oxygen atmosphere showed the excellent prop properties among them and these results could be explain by element and quantitative analysis in ZnO microstructure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.60-63
• /
• 2000

The $0.94MgTiO_3-0.06SrTiO_3$ ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and DT-TGA. According to the X-ray diffraction patterns of the $0.94MgTiO_3-0.06SrTiO_3$ ceramics, the cubic $SrTiO_3$ and hexagonal $MgTiO_3$ structures were coexisted. Increasing the sintering temperature from $1325^{\circ}C$ to $1400^{\circ}C$, average grain size was increased from $5.026{\mu}m$ to $8.377{\mu}m$. In the case of the $0.94MgTiO_3-0.06SrTiO_3$ ceramics sintered at $1325^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 21.66, 2,522(at 7.34GHz), $+71ppm/^{\circ}C$, respectively.

• Korean Journal of Microbiology
• /
• v.4 no.1
• /
• pp.1-13
• /
• 1966

The author examined for observing the structures of pyrenoid and cell wall of three strains of Chlorella ellipsoidea and relation of pyrenoid to starch grain formation at the ultrastructure level. 1. The development of pyrenoid of Chlorella species from the time of its initiation and its subdetail sequent activities are described in some pictures. 2. Close correlation between the findings of light microscopy and electron microscopy is proved. 3. The pyrenoid is a dynamic organellae which continues to change its appearance thoughout the development of the Chlorella cell. 4. The starch grains are continously formed by deposition of carbohydrate within the chloroplast with the aid of pyrenoid factors. 5. Some parental starch grains are passed on the daughter cell during cell division. 6. The Da stage cells contain only chlaroplast without pyrenoid matrix. In Da stage a pyrenoid is surrounded by starch and starch grains appear in chloroplast lamellae. In $L_1L_2$ stages, large starch grains of lens form accumulate in cell. In $L_3$ stage pyrenoid disappears for a time and starch grains are scattered. In cell division stage starch grains are divided into four groups. In $L_4$ stage, pyrenoid substance appears temporarily and disappears soon. At this stage the cell is constituted of Dn cell containing chloroplast only. 7. The cellular boundary of JE strain except Y 815 and Y 511 strain contains 250.angs. intermediate layer of unknown chemical composition between the fibrillar cellulose wall and the out capsule layer.