• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.276-280
• /
• 2019

In this study, we investigated the crystal defects and grain boundary properties in a ZZCCC ($ZnO-Zn_2BiVO_6-Co_3O_4-Cr_2O_3-CaCO_3$) varistor, with the liquid-phase sintering aid $Zn_2BiVO_6$ developed by our laboratory. The ZZCCC varistor sintered at $1,200^{\circ}C$ exhibited excellent nonlinear current-voltage characteristics (${\alpha}=63$), with oxygen vacancy ($V_o^*$ ; 0.35 eV) as a main defect, and an apparent activation energy of 1.1 eV with an electrically single grain boundary. Therefore, among the various additives to improve the electrical properties of ZnO varistors, if $Zn_2BiVO_6$ is used as a liquid phase sintering aid, it will be ideal to use Co for the oxygen vacancy and Ca for the electrically single grain boundary. This will allow the good properties of ZnO varistors to be maintained up to high sintering temperatures.

• Korean Journal of Crystallography
• /
• v.7 no.2
• /
• pp.156-164
• /
• 1996

The atomic configurations of GaAs ∑19, {331}/{331} [110] and ∑3 {111}/{111} [110] tilt grain boundaries were investigated by HRTEM (High-resolution Transmission Electron Microscopy). The boundary planes lie parallel to the crystallographic planes with high number density of coincident lattice sites for given misorientations, exhibiting particular atomic structural units. Secondary boundary dislocations with a core diameter of about 2nm were observed at boundary steps when a slight deviation from exact ∑-related misorientations occurs in the bicrystal system. The relation between the secondary boundary dislocation and the boundary step was discussed based on a DSC lattice model.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1159-1160
• /
• 2006

For pure Molybdenum carburized in mixed gases of argon and carbon monoxide, microstructural observations were carried out. X-ray diffraction analysis for carburized specimens revealed that brittle ${\alpha}-Mo_2C$- layer hardly formed in the case of low carbon monoxide concentration. Fracture strength of the specimen carburized at 1673 K for 16 h is about 550 MPa higher than that of the un-carburized specimen. SEM observation revealed that with increasing carburizing temperature, the region demonstrating a transgranular fracture mode progressed towards the center of specimen. This result means that the grain boundaries were strengthened by the grain boundary diffusion of carbon and the strength of grain boundaries exceeded that of grain itself.

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.769-775
• /
• 2019

The tensile strength of irradiated 3C-SiC, SiC with artificial point defects, SiC with symmetric tilt grain boundaries (GBs), irradiated SiC with GBs are investigated using molecular dynamics simulations at 300 K. For an irradiated SiC sample, the tensile strength decreases with the increase of irradiation dose. The Young's modulus decreases with the increase of irradiation dose which agrees well with experiment and simulation data. For artificial point defects, the designed point defects dramatically decrease the tensile strength of SiC at low concentration. Among the point defects studied in this work, the vacancies drop the strength the most seriously. SiC symmetric tilt GBs decrease the tensile strength of pure SiC. Under irradiated condition, the tensile strengths of all SiC samples with grain boundaries decrease and converge to certain value because the structures become amorphous and the grain boundaries disappear after high dose irradiation.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.10a
• /
• pp.34-34
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2008.05a
• /
• pp.43.1-43.1
• /
• 2008

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.307-312
• /
• 2018

Liquid phases in ZnO varistors cause more complex phase development and microstructure, which makes the control of electrical properties and reliability more difficult. Therefore, we have investigated 2 mol% $CaCO_3$ doped $ZnO-Co_3O_4-Cr_2O_3-La_2O_3$ (ZCCLCa) bulk ceramics as one of the compositions without liquid phase sintering additive. The results were as follows: when $CaCO_3$ is added to ZCCLCa ($644{\Omega}cm$) acting as a simple ohmic resistor, CaO does not form a secondary phase with ZnO but is mostly distributed in the grain boundary and has excellent varistor characteristics (high nonlinear coefficient ${\alpha}=78$, low leakage current of $0.06{\mu}A/cm^2$, and high insulation resistance of $1{\times}10^{11}{\Omega}cm$). The main defects $Zn_i^{{\cdot}{\cdot}}$ (AS: 0.16 eV, IS & MS: 0.20 eV) and $V_o^{\bullet}$ (AS: 0.29 eV, IS & MS: 0.37 eV) were found, and the grain boundaries had 1.1 eV with electrically single grain boundary. The resistance of each defect and grain boundary decreases exponentially with increasing the measurement temperature. However, the capacitance (0.2 nF) of the grain boundary was ~1/10 lower than that of the two defects (~3.8 nF, ~2.2 nF) and showed a tendency to decrease as the measurement temperature increased. Therefore, ZCCLCa varistors have high sintering temperature of $1,200^{\circ}C$ due to lack of liquid phase additives, but excellent varistor characteristics are exhibited, which means ZCCLCa is a good candidate for realizing chip type or disc type commercial varistor products with excellent performance.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.888-892
• /
• 1992

The chemically induced grain-boundary migration has been studied in MgAl2O4 spinel under ZnO atmosphere. MgAl2O4 compacts been prepared by sintering powder mixture of Al2O3 and MgO at 1$600^{\circ}C$ for 60 h in air. The sintered MgAl2O4 has been heat-treated at 150$0^{\circ}C$ in a ZnO atmosphere. During the heat-treatment grain boundaries have become curved or faceted, and the total area of grain boundaries have increased. In the migrated region, the ZnO content is higher by 6 wt% than that in other regions, indicating that the migration was induced by addition of ZnO. In some shrinking grains, the faceted planes of different grain boundaries for the same grain are parallel to each other. This result provide an experimental support for the coherency strain energy in diffusion layer of the shrinking grain as being the major driving force. Calculated coherency strain energy of MgAl2O4 shows the maximum at {111} planes and the minimum at {100} planes. Although the minimum surface energy is at {111} planes, the faceted moving boundaries are expected to be {100} planes because of lowest driving force for the grain-boundary migration.

• Korean Journal of Materials Research
• /
• v.9 no.9
• /
• pp.919-925
• /
• 1999

Grain boundary characteristics and corrosion behavior of Alloy 600 material were investigated using the concept of grain boundary control by thermomechanical treatment(TMT). The grain boundary character distribution (GBCD) was analyzed by electron backscattered diffraction pattern. The effects of GBeD variation on intergranular at tack(JGA) and primary water stress corrosion cracking(PWSeC) were also evaluated. Changes in the fraction of coinci dence site lattice(CSL) boundaries in each cycle of TMT process were not distinguishable, but the total eSL boundary frequencies for TMT specimens increased about 10% compared with those of the commercial Alloy 600 material. It was found from IGA tests that the resistance to IGA was improved by TMT process. However, it was found from PWSCC test that repeating of TMT cycles resulted in the gradual decrease of the time to failure and the maximum load due to change in grain boundary characteristics, while the average crack propagation rate of primary crack increased mainly due to suppression of secondary crack propagation. It is considered that these corrosion characteristics in TMT specimens is attributed to 'fine tuning of grain boundary' mechanism.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.43-45
• /
• 2003

The empirical model for predicting the prior austenite grain size in low-alloy steel weld HAZ was developed through examining the effect of alloying element. The test alloys were made by vacuum induction melting. Grain growth behaviors were observed and analyzed by isothermal grain growth test and subsequent metallography. As a result, it was found that the grain growth might be controlled by grain boundary diffusion and the empirical model for grain growth was presented.