• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.777-783
• /
• 2013

We used dipodal type bis[3-(trimethoxysilyl)propyl]amine (BTMA) silane coupling agent to modify silica nanoparticles to introduce secondary amino groups on the silica surface. These grafted N-H groups were reacted with glycidyl methacrylate (GMA) to introduce polymerizable methacrylate groups on the silica surface. After modification reaction, we used several analytical techniques such as Fourier transform infrared spectroscopy (FTIR), elemental analysis (EA) and solid state $^{13}C$ cross-polarization magic angle spinning (CP/MAS) nuclear magnetic resonance spectroscopy (NMR) to analyze the effects of reaction time, reaction temperature and used GMA concentration on the modification degree between N-H groups on the silica surface and epoxide groups of GMA. We found increased introduction of methacrylate groups on the silica surface by ring opening reaction of epoxide groups of GMA with N-H groups on BTMA treated silica with increased reaction time, reaction temperature and used GMA concentration within our experimental conditions.

• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.848-854
• /
• 2001

The crystallization behavior of poly (ethylene terephthalate) (PET) /ethylene-methyl acrylate-glycidyl methacrylate copolymer (E-MeA-GMA) blend was studied. The extent of reaction and the reaction rate between PET and E-MeA-GMA were measured with torque rheometer, FT-IR and SEM. The effects of the grafting reaction on the crystallization behavior were investigated with DSC and time-resolved light scattering (TR-LS) techniques. The morphological change at the lamellar level was also examined by using a small angle X-ray scattering (SAXS) method.

• Carbon letters
• /
• v.11 no.4
• /
• pp.311-315
• /
• 2010

In this work, the effect of glycidyl methacrylate grafted multi-walled carbon nanotubes (GMA-MWCNTs) on the viscoelastic behaviors of polypropylene (PP) based nanocomposites was studied. The GMA-MWCNTs/PP was prepared using a bravender at $200^{\circ}C$ by melt mixing as a function of GMA-MWCNT content. The viscoelastic behaviors of GMA-MWCNTs/PP nanocomposites were measured by a rheometer. It was found that the GMA-MWCNTs were homogeneously dispersed in the PP matrix. The GMA-MWCNTs/PP nanocomposites showed higher storage modulus, loss modulus, and shear viscosity compared to pure PP nanocomposites and the maximum value was shown at 2.0 wt% GMA-MWCNTs loading. These results were probably attributed to the strong interfacial interaction between the GMA-MWCNT and the PP matrix.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.137-144
• /
• 2012

The surface of polyethylene (PE) was modified through Ar atmospheric pressure plasma treatment and subsequent grafting of glycidyl methacrylate (GMA). Optimum plasma treatment conditions were determined through analyzing the surface free energies calculated from the contact angles between PE samples and three probe liquids, which were RF-power of 200 W, plasma treatment time of 600 sec, Ar flow rate of 5 LPM, and sample-holder moving speed of 20 mm/sec. To introduce the maximum amount of GMA on PE surface treated under the conditions, graft copolymerization conditions such as GMA concentration, temperature, and time were carefully controlled. Grafting degree (GD) was obtained through weight difference analysis of PE film before and after graft copolymerization. A maximum GD was achieved at the GMA concentration of 20 vol%, the temperature of $80^{\circ}C$, and the treatment time of 4 hr.

• Journal of the Korean Chemical Society
• /
• v.15 no.5
• /
• pp.281-284
• /
• 1971

Copolymerization of glycidyl methacrylate(GMA) with methyl acrylate(MA) and the reaction of the copoly mer with primary amines were investigated. The monomer reactivity ratios were determined by Mayo-Lewis intersecting method. $r_1=0.22{\pm}0.03(GMA),\;r_2=0.50{\pm}0.07(MA)$. GMA and MA copolymerized to afford the polymer having good alternate arrangements of the units of the monomers.

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.124-130
• /
• 2008

In order to fabricate a modified poly (lactic acid) (PLA) for applications requiring high melt strength, a PLA has been irradiated in the presence of functional monomer of glycidyl methacrylate (GMA). Samples were prepared with various contents of GMA and irradiation dosages, and were characterized by observing their thermal and melt viscoelastic properties and gel faction. The complex viscosity and storage modulus of the modified PLA without GMA were lower than those of the original PLA. Those of the modified PLA decreased with increasing dosage. In the case of the modified PLA containing 0.1 phr or 0.3 phr of GMA, their changing tendency with dosage was similar to the irradiated PLA without GMA. However, the 5 kGy irradiated PLA containing 0.5 phr of GMA showed the greatly enhanced complex viscosity and storage modulus, which were about 3 and 10 times higher than those of the original PLA at a frequency of 0.1 rad/s, respectively.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.65-70
• /
• 2012

Glycidyl methacrylate (GMA) was used to introduce epoxy groups on the surface of polypropylene (PP) plate, used as a substrate, through plasma-induced graft copolymerization. Emulsion polymerization was applied for graft copolymerization of GMA and was compared with conventional solution polymerization to confirm its effect. Plasma treatment conditions under one atmospheric pressure were fixed as follows; the RF power of 200 W, the treatment time of 30 sec, the Ar gas flow rate of 6 LPM, and the exposure time of treated PP samples in air of 5 min. For graft-copolymerization, GMA concentration, reaction temperature, and reaction time was optimized to maximize the grafting degree of GMA. The maximum grafting degree of GMA was obtained at the condition of 12%-GMA concentration, $90^{\circ}C$ reaction temperature, and 5 hr-reaction time. Analysis results supported that the emulsion polymerization was more effective than the solution polymerization for grafting more GMAs on the surface of PP plate under the same reaction conditions.

• Korean Chemical Engineering Research
• /
• v.51 no.3
• /
• pp.342-346
• /
• 2013

In this study the cycloaddition of glycidyl methacrylate (GMA) and $CO_2$ using ionic liquid as catalyst was performed for the technology of $CO_2$ reduction. The structure of synthesized cyclic carbonate, [2-oxo-1,3-dioxolan-4-yl]methacrylate (DOMA) was analyzed and confirmed by FT-IR and $^1H$-NMR. The change in conversion with respect to reaction time was investigated using $^1H$-NMR. Interestingly, the ionic polymerization of vinyl groups and crosslinking reaction between cyclic carbonate rings of DOMA were observed following completion of cycloaddition.

• Macromolecular Research
• /
• v.11 no.6
• /
• pp.495-500
• /
• 2003

UV-induced graft polymerization of glycidyl methacrylate (GMA) to a polypropylene (PP) membrane was carried out in the vapor phase with benzophenone (BP) as a photoinitiator. Attenuated total reflection Fourier transform infrared spectroscopy, atomic force microscopy (AFM), and scanning electron microscopy (SEM) were utilized to characterize the copolymer. The degree of grafting increased with increasing reaction time, increased UV irradiation source intensity, and increased immersion concentration of the BP solution. The optimum synthetic condition for the PP-g-GMA membrane was obtained with a reaction time of 2 hrs, a UV irradiation source intensity of 450 W, and an immersion concentration of the BP solution of 0.5 mol/L. The pure water flux decreased upon increasing the degree of grafting and increasing the amount of diethylamino functional group introduced. The analysis of AFM and SEM images shows that the graft chains and diethylamino groups of PP-g-GMA grew on the PP membrane surface, resulting in a change in surface morphology.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.256-262
• /
• 2010

Dispersion polymerization of methyl acrylate, ethyl acrylate, butyl acrylate, and glycidyl methacrylate were performed in supercritical $CO_2$ at $80\;^{\circ}C$ and 346 bar. Glycidyl methacrylate linked poly(dimethylsiloxane) (GMS-PDMS) surfactant, which was prepared by linking glycidyl methacrylate to monoglycidyl ether terminated PDMS with amino-propyltriethoxysilane, was used as surfactant for the dispersion polymerization in $CO_2$. The yield of the poly(alkyl acrylate) polymers, synthesized in $CO_2$ medium, decreased as the alkyl tail of the acrylate monomers increased. Poly(glycidyl methacrylate) and poly(methyl acrylate) were produced in bead form whereas poly(ethyl acrylate) and poly(butyl acrylate) were viscous liquid. The poly(glycidyl methacrylate) particles had a number average diameter of 2.45 ${\mu}m$ and monodisperse distribution. The poly(methyl acrylate) had a number average diameter of 0.52 ${\mu}m$ and the particle size distribution was bimodal. The glass transition temperatures ($T_g$) of the poly(glycidyl methacrylate) and the poly(alkyl acrylate) products were 4~9 K higher than the $T_g$ of the corresponding acrylate polymers synthesized in conventional processes.