• 한국주조공학회지
• /
• 제29권4호
• /
• pp.181-186
• /
• 2009

The interrelationship between new parameter ${\sigma}$ and maximum diameter $D_{max}$ is elaborated and discussed in comparison with four other glass forming ability (GFA) parameters, i.e. (1) super-cooled liquid region ${\Delta}T_x (=T_x - T_g)$, (2) reduced glass transition temperature $T_{rg} (=T_g/T_l)$, (3) K parameter $K (=[T_x-T_g]/[T_l -T_x])$, and (4) gamma parameter ${\gamma}(=[T_x]/[T_l+T_g])$ in Ca-based bulk metallic glass (BMG) systems. The ${\sigma}$ parameter, defined as ${\Delta}T^*{\times}P^'$, has a far better correlation with $D_{max}$ than the GFA parameters suggested so far, clearly indicating that the liquid phase stability and atomic size mismatch dominantly affect the GFA of Ca-based BMGs. Thus, it can be understood that the GFA of BMGs can be properly described by considering structural aspects for glass formation as well as thermodynamic and kinetic aspects for glass formation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.91-91
• /
• 2008

$SnO_2-B_2O_3-P_2O_5$ system were prepared by melt-quenching technique in the compositional series containing 50, 55 aod 60mol.% of $SnO_2$. A large glass-forming region was found at the phosphate side of the ternary system with homogeneous glasses containing up to 5-25mol.% of $B_2O_3$. For these glasses, thermal expansion coeffient($\alpha$), glass transition temperature(Tg), and glass softening temperature(Ts), were determined. The values a decrease with increasing $B_2O_3$ content, while Tg and Ts increased. The reason for the observed changes is local structure of the glasses. Local structure of the glasses was investigated by Raman and FT-IR measurements, suggesting that the number of bridging oxygens decreased whereas the non-bridging oxygen concentration increased with increasing $SnO_2$ content in the glasses.

• 한국주조공학회지
• /
• 제35권4호
• /
• pp.75-79
• /
• 2015

Commercial Zr-based amorphous alloy was recycled and oxygen was introduced during the recycling process. The oxygen content can have a great effect on the glass forming ability and the mechanical properties of the alloy. Therefore, it was closely examined. The initial oxygen content in the raw material was 1,244 ppm. It was increased to 3,789 ppm in the alloy after ten recycling processes. As the recycling processes were repeated, the oxygen content increased. Specifically, after four recycling processes, it increased sharply as compared to that after three recycling processes. After ten recycling processes, the glass transition temperature (Tg) increased from 613 K to 634 K and the crystallization temperature (Tx) increased from 696 K to 706 K. On the other hand, the super-cooled liquid region (${\Delta}T=Tx-Tg$) decreased slightly from 83 K to 72 K while the reduced glass transition temperature (Trg = Tg/Tm) was 0.63, remaining constant even when the oxygen content was increased. These results indicated that the increased oxygen content deteriorated the glass forming ability. The bending strength as determined in a three-point bending test showed a sharp decrease from 3,055 to 2,062 MPa as the oxygen content was increased from 1,244 ppm to 3,789 ppm; the extension was also decreased from 3.02 to 1.74 mm. These findings meant that the alloy became brittle.

• 한국세라믹학회지
• /
• 제40권11호
• /
• pp.1132-1137
• /
• 2003

환경친화적인 유리비료로서의 응용을 위해 인산염계 유리의 용출특성에 대한 연구를 진행하였다. 0.1K₂O-0.1SiO₂-0.6P₂O/sub 5/계 유리를 기본조성으로 하고, CaO와 MgO의 함량변화를 준 다양한 유리조성에 대한 유리 형성 조건을 확인하고자 하였다. 또한 CaO 및 MgO의 함량변화에 따른 열적특성 및 용출 특성 변화를 확인하였다. MgO 함량의 증가에 따라 유리 전이온도 및 연화온도는 증가하였으며, CaO 및 MgO의 함량변화에 따라 용출특성에 큰 영향을 미치는 것을 확인하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.123-126
• /
• 2007

Deformation behavior of $Zr_{55}Cu_{30}Al_{10}Ni_5$ (at. %) bulk metallic glass (BMG) fabricated by suction casting method has been investigated at elevated temperatures in this study. The BMG was first verified to have an amorphous structure thru X-ray diffraction (XRD) and differential scanning calorimetry (DSC). A series of compression tests has consequently been performed in supercooled liquid temperature region to investigate the high temperature deformation behavior. A transition from Newtonian to non-Newtonian flow appeared to take place depending upon both the strain rate and test temperature. A processing map based on a dynamic materials model has been constructed to estimate a feasible forming condition for this BMG alloy.

• 소성∙가공
• /
• 제16권4호
• /
• pp.309-312
• /
• 2007

Deformation behavior of $Zr_{55}Cu_{30}Al_{10}Ni_5$(at. %) bulk metallic glass(BMG) fabricated by suction casting method has been investigated at elevated temperatures in this study. The BMG was first verified to have an amorphous structure with the analysis of X-ray diffraction(XRD) and differential scanning calorimetry(DSC) data. A series of compression tests has consequently been performed in the region of supercooled liquid temperature to investigate the behavior of high temperature deformation. A transition from Newtonian to non-Newtonian flow appeared to take place depending upon both the strain rate and test temperature. A processing map based on a dynamic materials model has been constructed to estimate a feasible forming condition for this BMG alloy.

• Journal of Magnetics
• /
• 제8권2호
• /
• pp.85-88
• /
• 2003

The magnetic and transport properties far single crystals of Ru-doped mono-layered manganites $La_{0.5}Sr_{1.5}-Mn_{1-x}Ru_xO_4$ (0$\leq$$\chi$$\leq$0.1) have been studied using neutron diffraction and magnetization measurements. Temperature dependent magnetization data reveal that with an increase in the Ru concentration the parent charge ordered antiferromagnetic state is gradually destroyed and new ferromagnetic phase evolves. In the low Ru-doped system spin glass behavior is apparent in low temperature region, which is confirmed by ac and do magnetization measurements. The competing magnetic interaction between Mn/Mn and Mn/Ru couples is the most likely cause of the spin glass transition.

• 한국생산제조학회지
• /
• 제21권2호
• /
• pp.191-195
• /
• 2012

Heavy flint optical glass(SF57HHT) is new material that has extremely high transmittance. Due to brittleness and high hardness, optical glass is one of the most difficult to materials for ultra-precision turning. According to the hypothesis of ductile machining, all materials, regardless of their hardness and brittleness, will undergo transition from brittle to ductile machining region below critical undefromed chip thickness. In this study, cutting test was carried out to evaluate cutting performance of heavy flint glass using ultra-precision machine with single crystal diamond bite. The machined workpiece surface topography, tool wear and surface roughness were examined using AFM and SEM. The experimental results indicate that the machining mode become the brittle mode to ductile mode, when the maximum undeformed chip thinkness is large than critical value. Tool wear mainly occurs on the flank face and its wear mechanism is dominated by abrasion. This study demonstrates the feasibility of SF57HHT by diamond turning.

• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.382-385
• /
• 2011

There is an immense need to obtain nanometric surface finish on optical glass owing to the advantage of improved performance of the components. But owing to brittleness and hardness, optical glass is one of the materials that is difficult to ultra-precision turning. According to the hypothesis of ductile mode machining, regardless of their hardness and brittleness, will undergo a transition from brittle to ductile machining region below a critical undeformed chip thickness. Below this threshold, it is suggested that the energy required for plastic formation. Thus, plastic deformation is the predominant mechanism of material removal in machining these materials in this mode. An experimental study is conducted diamond cutting for machining BK7 glass. The investigation presents the feasibility of achieving nanometric surface and the understanding the mechanism of cutting glass, proving the cutting edge radius effect.

• 폴리머
• /
• 제24권6호
• /
• pp.787-793
• /
• 2000

분자량과 methylacrylate 함량이 다른 아크릴로니트릴 공중합체의 dimethylformamide (DMF) 농후용액의 겔화 거동 및 임계 겔농도 (c＊)를 조사하였다. 중합체 종류에 관계없이 저온에서 장시간 방치할 경우 방치시간에 따라 점도가 급격히 증가하여 겔화가 진행됨을 알았으며, 중합체의 분자량이 클수록, 방치온도가 낮을수록 그리고 공중합체 중 아크릴로니트릴 성분비가 증가할수록 겔화 진행속도가 증가하였고, 임계 겔농도는 감소하였다. 동적 점탄성 실험에서 겔 용액으로부터 얻은 필름은 진 용액으로부터 얻은 필름과 달리 두 개의 유리전이 영역을 나타내었다. 이러한 결과는 겔화과정에서 atactic 중합체중 입체 규칙적인 block들간의 쌍극자-쌍극자 상호작용에 의한 ordered junction zone의 존재를 강하게 시사하였다.