• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.229-238
• /
• 2002

This paper introduces the surface roughness parameter, Rs to the characterization of joint roughness and quantitatively illustrates the influence of joint roughness on the joint shear strength. A new peak shear strength criterion for rock joints using Rs is suggested. The results show that the surface roughness parameter, Rs can appropriately reflect the degree of roughness for the rock joint surfaces tested in this study A measuring interval of 2mm and profile length of 5cm can be used to characterize the joint roughness of the rock core size surfaces; however, the scale of fluctuation, $\delta_\alpha$ should be considered to extend the surface roughness parameter, Rs to the large-scale field rock joint surfaces. For the smooth joint roughness, sliding of the rock cores is the principal shear mechanism; however, the breakage of roughness from the rock cores is inferred for rougher joint roughness.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.29-41
• /
• 1999

This Paper applied a simple strength parameter averaging method to double layered systems consisting of the strong sand layer overlying the soft clay deposit. This study derived a formula which defines a critical depth as the strength parameters, and used the correction parameter, $\alpha$ to reduce an error of the strength parameter averaging method. The results of the method were presented in the form of dimensionless charts and were compared with the results of several solutions proposed by Satyanarayana & Grag, Sreenivasulu, and Meyerhof & Hanna. The results of the proposed method coincided with the method of Meyerhof & Hanna and the results obtained from FLAC. But the Satyanarayana & Grag method and the Sreenivasulu method overestimated the bearing capacity. Consequently, the bearing capacity of foundation on sand layer overlying soft clay layer can be approximately estimated by using the proposed dimensionless charts.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.27-35
• /
• 2008

At low normal stress levels tensile strength of sand varies with either saturation or suction of soil in an up-and-down manner with a peak tensile strength that can occur at any degree of saturation. A theory that accurately predicts tensile strength of wet sand is presented. A closed form expression for tensile strength unifies tensile strength characteristics in all three water retention regimes: pendular, funicular, and capillary. Three parameters are employed in the theory; namely, the Internal friction angle (at low normal stress) ${\phi}_t$, the inverse value of the air-entry pressure ${\alpha}$, and the pore size spectrum parameter n. It is shown that the magnitude of peak tensile strength is dominantly controlled by the ${\alpha}$ parameter. The saturation at which peak tensile strength occurs only depends on the pore size spectrum parameter n.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.591-604
• /
• 2008

In this study, two design examples of drilled shafts on soft ground in Ho-Chi-Minh City, Vietnam are introduced. One is for a 27-story apartment and the other is for a Arch bridge over Saigon river. Unlikely the normal cases in Korea, all of the bored pile foundations are supposed to be placed on soil layers. Therefore, skin friction between pile and ground is the most crucial design parameter. Three methods using SPT N value of sandy soil -Korean Road Bridge Code(1996), Reese and Wright (1977), and O'Neill and Reese (1988)- were adopted to obtain an ultimate axial bearing capacity. In order to verify the calculated bearing capacity, 3 sets of static load test and a Osterberg Cell test were performed at an apartment site and a bridge site respectively. LRFD (Load Resistance Factored Design) method was compared with ASD (Allowable Stress Design) method. On application of ASD method, safety factor for skin friction was adopted as 2 or 3 while safety factor for end bearing was 3. The design bearing capacities from ASD method matched well with those from LRFD method when safety factor for skin friction was adopted as 2.

• Geomechanics and Engineering
• /
• v.21 no.3
• /
• pp.289-300
• /
• 2020

Estimating the damage induced by an explosion around a blast hole has always been a challenging issue in geotechnical engineering. It is difficult to determine an exact dimension for damage zone since many parameters are involved in the formation of failures, and there are some uncertainties lying in these parameters. Thus, the present study adopted a probabilistic approach towards this problem. First, a reliability model of the problem was established and the failure probability of induced damage was calculated. Then, the corresponding exceedance risk curve was developed indicating the relation between the failure probability and the cracked zone radius. The obtained risk curve indicated that the failure probability drops dramatically by increasing the cracked zone radius so that the probability of exceedance for any crack length greater than 4.5 m is less than 5%. Moreover, the effect of each parameter involved in the probability of failure, including blast hole radius, explosive density, detonation velocity, and tensile strength of the rock, was evaluated by using a sensitivity analysis. Finally, the impact of the decoupling ratio on the reduction of failures was investigated and the location of its maximum influence was demonstrated around the blast point.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.1
• /
• pp.61-70
• /
• 2013

This paper presents the results of a two-dimensional finite element analysis of end bearing capacity of single pile installed in fractured rock mass. A number of cases were analyzed using Hoek-Brown criterion that can consider the condition of rock joints. Considering a wide range of joint conditions in which the pile is embedded into the rock, GSI was set as a main parameter. And the effects of pile diameter, unconfined compressive strength of rock and Hoek-Brown constant $m_0$ were considered. Based on parameter study, end bearing load factor graphs were suggested.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.1
• /
• pp.149-159
• /
• 2013

This paper deals with behaviors of Poisson's ratio with water content through uniaxial compressive strength against 307 individual rock cores, which are classified into sedimentary, igneous and metamorphic rock. Poissons' ratio demonstrates independent behaviors and does not correlate with mechanical and physical parameter of rocks. The water content behavior of Poissson's ratio represents decrease, increase and random style. Rock samples with decreasing behavior demonstrate absolute preponderance above the 70% level. As Poisson' ratio shows independent behaviors, it should be considered based on experimental results of in-situ rock in the process of design, construction, and supervision.

• Geotechnical Engineering
• /
• v.8 no.4
• /
• pp.67-80
• /
• 1992

In the analysis of dynamic problem, determination of mazimun shear modulus is essential for the estimation of shear stress at any strain level. Although many models for silica sands were presented, the direct accomodation of those models to crushable sand would be difficult because of crushability during torsion. In this research dynamic behaviour of tested sand is presented. The shear modulus of loose crushable sand shows similar results to silica sand. However, as the density of crushable sand increases the shear modulus decreases because of crushability by increasing surface contact area. And modulus number is expressed in terms of state parameter by Been and Jefferies (1965).

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.15-24
• /
• 2005

Modeling techniques of piled pier were reviewed and the influences of pile cap's boundary conditions were analyzed in this study. The method using flexible springs seems to be useful fur the practical design since its simplified model can represent the complex behaviors of pile groups efficiently. Parameter studies were performed far various pile group arrangements, pile spacings, end bearing conditions, and loading stages to analyze their effects on the lateral displacements, maximum pile bending stresses, and lateral stiffness of pile groups. Through the parameter studies, it was found that when lateral stiffness of pile groups was estimated by using three-dimensional analysis method (YSGroup), its complex behavior could be predicted better than other methods based on single pile analysis.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1024-1029
• /
• 2008

In this study, new parameter related with compression index was derivated from piezocone test results. It is assumed that the consolidation coefficient obtained by piezocone test is concerned with the volume change during piezocone dissipation. Based on that assumption, new parameter in terms of consolidation coefficient from piezocone test was introduced. The new parameter from piezocone test and the compression index from laboratory consolidation test shows linear relationship.