• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.176-183
• /
• 2001

It is difficult to find out the kinematic characteristics of a vehicle suspension without the usage of CAE software. The application of CAE software into suspension kinematics and dynamics yields the more precise knowledge on the chassis design. In this study, the influence of the suspension geometry on the handling performances of a large-sized bus is investigated using the DADS software. The front and rear suspension of a large-sized bus are a rigid axle suspension with the four control links. The elastokinematic analysis is performed to evaluate the roll characteristics of the front and rear suspension. The elastokinematic responses are evaluated in terms of the roll center height and roll steer for various geometric parameters. The roll center height is mainly dependent on the vertical displacement of a panhard rod and the vertical displacements of lower control links affect the roll steer of a rear suspension. The parameter study with the change of rear suspension geometry is conducted to investigate the vehicle handling performances. This parameter study shows that the vertical displacement and orientation of a panhard rod influence the handling performances of a large-sized bus significantly.

• Journal of Welding and Joining
• /
• 제29권4호
• /
• pp.41-47
• /
• 2011

GMA welding process is a production process to improve productivity for the provision of higher welding quality of material. These includes numerous process variables that could affect welding quality, productivity and cost savings. Recently, the welding part of construction equipment had frequent failure of major components in the welding part of each subsidiary material due to shock which is very poor according to the welding part. Therefore, the implementation of sound welding procedure is the most decisive factor for the reliability of construction machinery. The data generated through experiments conducted in this study has validated its effectiveness for the optimization of bead geometry and process variables is presented. The criteria to control the process parameters, to achieve a good bead geometry. This study has developed mathematical models and algorithms to predict or control the bead geometry in GMA fillet welding process.

• 한국CDE학회논문집
• /
• 제18권3호
• /
• pp.234-242
• /
• 2013

Different CAD systems are used in ship outfitting design on different usage and purpose. Therefore, data exchanges between CAD systems are required from different formats. For data exchange, boundary representation standard formats such as IGES and ISO 10303 (STEP) are widely used. However, they present only B-rep representation. Because of different CAD systems have their own geometry format, data exchanges with design intend are difficult. Especially, Tribon and PDMS use primitives for express their geometry in ship outfitting design. However, Tribon primitives are represented their parameter by values that are non-parametric. Therefore, data size of catalogue library is bigger than different CAD system using parametric primitive representation. And that system has difficulty on data reprocessing. To solve that problem, we discuss about shape DB which contains design parameters of primitive for exchange Tribon primitives. And geometry data exchange between Tribon and Shape Database that defines based on PDMS scheme are specified using primitive mapping that can represent design intend.

• Journal of Communications and Networks
• /
• 제15권1호
• /
• pp.71-76
• /
• 2013

A new class of quantum low-density parity-check (LDPC) codes whose parity-check matrices are dual-containing matrices constructed based on lines of Euclidean geometries (EGs) is presented. The parity-check matrices of our quantum codes contain one and only one 4-cycle in every two rows and have better distance properties. However, the classical parity-check matrix constructed from EGs does not satisfy the condition of dual-containing. In some parameter conditions, parts of the rows in the matrix maybe have not any nonzero element in common. Notably, we propose four families of fascinating structure according to changes in all the parameters, and the parity-check matrices are adopted to satisfy the requirement of dual-containing. Series of matrix properties are proved. Construction methods of the parity-check matrices with dual-containing property are given. The simulation results show that the quantum LDPC codes constructed by this method perform very well over the depolarizing channel when decoded with iterative decoding based on the sum-product algorithm. Also, the quantum codes constructed in this paper outperform other quantum codes based on EGs.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.247-258
• /
• 2019

Soil strength and failure surface geometry directly influence magnitudes of passive earth thrust acting on geotechnical retaining structures. Accordingly, it is expected that as long as the shape of the failure surface geometry and strength parameters of the backfill are known, magnitudes of computed passive earth thrusts should be highly accurate. Building on this premise, this study adopts conventional method of slices for calculating passive earth thrust and combines it with equations for estimating failure surface geometries based on in-situ stress state and density. Accuracy of the proposed method is checked using the results obtained from small-scale physical retaining wall model tests. In these model tests, backfill was prepared using either air pluviation or compaction and different backfill relative densities were used in each test. When the calculated passive earth thrust magnitudes were compared with the measured values, it was noticed that the results were highly compatible for the tests with pluviated backfills. On the other hand, calculated thrust magnitudes significantly underestimated the measured thrust magnitudes for those tests with compacted backfills. Based on this observation, a new approach for the calculation of passive earth pressures is developed. The proposed approach calculates the magnitude and considers the influence of locked-in stresses that are the by-products of the backfill preparation method in the computation of lateral earth forces. Finally, recommendations are given for any geotechnical application involving the compaction of granular bodies that are equally applicable to physical modelling studies and field construction problems.

• Structural Engineering and Mechanics
• /
• 제70권1호
• /
• pp.33-41
• /
• 2019

The influence of two parameters on fatigue damage predictions of a variably loaded cantilever beam has been examined. The first parameter is the geometry of the cantilever beam and the weld connecting it to a rear panel. Variables of the geometry examined here include the cantilever length, the weld width on the critical cross-section and the angle of the critical cross-section. The second parameter is the safety factor, as set out by the Eurocode 3 standard. An analytical approach has been used to calculate the stresses at the critical cross-section and standard rainflow counting has been used for the extraction of the load cycles from the load history. The results here suggest that a change in the width and angle of the critical cross-section has a non-linear impact on the fatigue damage. The results also show that the angle of the critical cross-section has the biggest influence on the fatigue damage and can cause the weld to withstand fatigue better. The second parameter, the safety factor, is shown to have a significant effect on the fatigue damage calculation, whereby a slight increase in the endurance safety factor can cause the calculated fatigue damage to increase considerably.

• ETRI Journal
• /
• 제44권1호
• /
• pp.38-50
• /
• 2022

This paper presents a study on the use of encoder-derived features in decoder-side depth estimation. The scheme of multiview video encoding does not require the transmission of depth maps (which carry the geometry of a three-dimensional scene) as only a set of input views and their parameters are compressed and packed into the bitstream, with a set of features that could make it easier to estimate geometry in the decoder. The paper proposes novel recursive block splitting for the feature extraction process and evaluates different scenarios of feature-driven decoder-side depth estimation, performed by assessing their influence on the bitrate of metadata, quality of the reconstructed video, and time of depth estimation. As efficient encoding of multiview sequences became one of the main scopes of the video encoding community, the experimental results are based on the "geometry absent" profile from the incoming MPEG Immersive video standard. The results show that the quality of synthesized views using the proposed recursive block splitting outperforms that of the state-of-the-art approach.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2672-2677
• /
• 2007

An investigation of low Reynolds number flow in nozzles and diffusers which are widely used in the valveless micropump is presented. Flow characteristics in the nozzle and diffuser are explained in view of viscous effect and flow oscillation induced by pumping membrane. These calculation results show that the rectification property of valveless micropump is due to a flow separation in the diffuser and the separation is largely originated from the flow oscillation. Under the assumptions of steady flow velocity profile and flow separation in the diffuser, simplified analytical models are provided to see the dependency of rectification on the micropump geometry. Geometric parameters of channel length, nozzle throat, chamber size, and converging/diverging angle are depicted through the analytical models in low Reynolds number flow, and the prediction and experimental results are compared. This theoretical study can be used to determine the optimum geometry of valveless micropump.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.251-252
• /
• 2002

An algorithm has been developed to determine changes in surface topography on asperity level. The software stitches small but detailed images together to create one large image. If such an image is made before and after an experiment, their difference shows a direct 3D view of the changes in micro-geometry, rather than a change in surface parameters. The algorithm is described in detail and illustrated using artificial as well as real surfaces.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.435-441
• /
• 2011

Track geometry changes by traffic loads. The bigger the changes are, the worse the riding comfort and running stability of train. This is so-called track irregularity and is the most important quality parameters of ballasted track. To objectively assess track irregularity, track geometry should be able to be measured. Practically, railway companies in Korea use various track recording equipments to measure track irregularity. But this various equipments output different data due to their geometrical structure even measured at same location. In this report, the correlation of various track recording data used in Korea was reviewed.