• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.15-20
• /
• 2017

This study analyzed the load change of the gear generated by the operation of the vehicle recliner through Finite Element Analysis. The basic model of the recliner used was a commercial product, and the effect of the seat frame was excluded. The load conditions applied to the recliner were set considering gravity, the mass of the seat's back frame, and the weight of a person. The operating mode was set to move the seat back from the vertical to the reclined position. As a result, it was found that the tooth bending amount of the gear rim and wheel increased from the cam rotation angle of 450 degrees, and a change in the contact ratio occurred. Furthermore, excessive torque fluctuations occurred in the ranges of 390 to 450 and 750 to 710 degrees. It was found that this occurred in the region of about 30 degrees before and after the point where the x-axis direction load is larger than the y-direction load. From this torque fluctuation it was determined to likely to cause chattering noise.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.415.2-415.2
• /
• 2016

Triboelectric nanogenerator (TENG) is one of ways to convert mechanical energy sound, waves, wind, vibrations, and human motions to available electrical energy. The principal mechanism to generate electrical energy is based on contact electrification on material surface and electrostatic induction between electrodes. The performance of TENG are dependent on amount of the input mechanical energy and characteristics of triboelectric materials. Furthermore, the whole TENG system including mechanical structure and electrical system can effect on output performance of TENG. In this work, we investigated the effect of gear train on output performance and power conversion efficiency (PCE) of TENG under a given input energy. We applied the gear train on mechanical structure to improve the contact rate. We measured the output energy under a constant input energy by controlling the size of the working gear. We prepared gears with gear ratios (rin/rw) of 1, 1.7, and 5. Under the constant input energy, the voltage and current from our gear-based TENG system were enhanced up to the maximum of 3.6 times and 4.4 times, respectively. Also, the PCE was increased up to 7 times at input frequency of 1.5 Hz. In order to understand the effect of kinematic design on TENG system, we performed a capacitor experiment with rectification circuit that provide DC voltage and current. Under the input frequency of 4.5 Hz, we obtained a 3 times enhanced rectifying voltage at a gear ratio of 5. The measured capacitor voltage was enhanced up to about 8 fold in using our TENG system. It is attributed that our gear-based TENG system could improve simultaneously the magnitude as well as the generation time of output power, finally enhancing output energy. Therefore, our gear-based TENG system provided an effective way to enhance the PCE of TENGs operating at a given input energy.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.5
• /
• pp.40-45
• /
• 1995

The kinematical relationship of bevel gearsets lies at the root of the gear design. As the demand on precision bevel gears is increased in the related industries, the kinematic analysis of a pair of sperical involute bevel gears needs to be exactly evaluated for the computer aided design. Pitch cone angles of bevel gearsets have been calculated under the assumption that the geared system is equivalent to a coned roller system without slipping. But this kinematical model involves some errors in the value of the ratio of angular velocity. In this paper, the ratio of the angular velocity is exactly derived, based on the perfect involute tooth surface. Four nonlinear equations representing the kinematical relationships are numerically solved to obtain the pitch and base cone angles. The ratios of angular volocities according to pressure and shaft angles are calculated and compared with those of the approximate gear model.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.7
• /
• pp.827-833
• /
• 2011

Precision forging of gears has a lot of advantages when compared to conventional gear shaping, because it allows the manufacture of gear parts without flash and consequently without the need for subsequent machining operations. In this study, the cold forging process is determined to manufacture the cold forged product for the precision clutch gear used of a commercial automobile, To do this, shape ratio of initial shape having influence the forgeability of forged product is analyzed. The optimal initial shape of clutch gear is designed using the results of DEFORM-3D and the artificial neural network (ANN). The initial shape through the detail analysis results, such as metal flow, distributions of strain can be obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.11
• /
• pp.1949-1957
• /
• 2003

A hybrid finite element analysis was used to analyze the influence of ring gear rim thickness and spline number on the static properties of a planetary gear system with manufacturing errors. Both of these parameters affected the bearing force and critical stress. The effect of changes in the rim thickness on the load sharing between the gears depended on the type of manufacturing error. Ring flexibility improved the load sharing between planetary gears only in systems with planet tooth thickness or planet tangential errors; for other types of error, ring flexibility worsened the load sharing. To improve load sharing, rim thickness and spline number should be controlled within a specific range. The minimum rim thickness limit should be determined considering not only the critical stress but also the load sharing. The effect of the ring gear boundary condition was more apparent in a system with errors than in a normal system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.9
• /
• pp.21-27
• /
• 2022

The rotorcraft engine gearbox transmits the power generated by the turboshaft engine to the rotor by reducing the rotational speed and increasing the torque. The core of the rotorcraft engine gearbox is lightweight performance, which requires maximum weight reduction within the range that meets various requirements and constraints. Therefore, lightweight design through gear macro geometry optimization is necessary. In this study, gear macro geometry optimization was performed to reduce the weight of a rotorcraft engine gearbox. NSGA-III was used for the optimization, resulting in a combination of the gear ratio and macro geometry that minimizes the weight of the total gear. In addition, the safety factor of the gears satisfied the given conditions.

• International Journal of Automotive Technology
• /
• v.7 no.3
• /
• pp.295-301
• /
• 2006

A new combustion method of high compression ratio SI engine was studied and proposed in order to achieve high thermal efficiency, comparable to that of CI engine. Compression ratio of SI engine is generally restricted by the knocking phenomena. A combustion chamber profile and a cranking mechanism were studied to avoid knocking with high compression ratio. Because reducing the end-gas temperature will suppress knocking, a combustion chamber was considered to have a wide surface at the end-gas region. However, wide surface will lead to large heat loss, which may cancel the gain of higher compression ratio operation. Thereby, a special cranking mechanism was adapted which allowed the piston to move rapidly near TDC. Numerical simulations were performed to optimize the cranking mechanism for achieving high thermal efficiency. An elliptic gear system and a leaf-shape gear system were employed in numerical simulations. Livengood-Wu integral, which is widely used to judge knocking occurrence, was calculated to verify the effect for the new concept. As a result, this concept can be operated at compression ratio of fourteen using a regular gasoline. A new single cylinder engine with compression ratio of twelve and TGV(Tumble Generation Valve) to enhance the turbulence and combustion speed was designed and built for proving its performance. The test results verified the predictions. Thermal efficiency was improve over 10% with compression ratio of twelve compared to an original engine with compression ratio of ten when strong turbulence was generated using TGV, leading to a fast combustion speed and reduced heat loss.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.12-17
• /
• 2011

Gears are useful for power transmission due to excellent power transmission performance, low cost, and compactness. In addition, gears have constant speed ratio, compact structure, and excellent efficiency. In order to transmit higher power, the new multi-range transmission requires gears which have greater strength than the existing transmission. This study evaluates stability and durability through gear analysis of the multi-range transmission in commercial vehicles using ROMAX-DESIGNER program. Also, strength design evaluation is carried out by the analysis results which are compared with gear strength theory of AGMA standard. Bending stress and contact stress on gears are lower than their allowable stresses. Therefore, we can evaluate the safety of the gear strength design in multi-range transmission.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3246-3252
• /
• 1994

The vibration of meshing gear system is originated form teeth deformation, teeth contact ratio, profile error, etc. The gear vibration is classified as whine vibration during meshing and as rattle vibration during idling. In this study, the whine vibration is investigated under the assumption of piecewise linearity of elastic stiffness due to the variation of meshing. Numerical, theoretical and experimental investigations show the existence of the superharmonic components of the second and the third order. consistently It can be concluded that the superharmonic components in whine vibration of meshing gear is originated from the stiffness variation. It also shows that the higher order harmonics are reduced on the increase of motor speed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.1
• /
• pp.21-29
• /
• 2016

To overcome the large ring gear manufacturing problems seen in slewing bearings and girth gears, pin gear drive units have been developed. Among them, a novel slewing bearing with an internal pinwheel gear set (i-PGS) is introduced in this paper. First, we consider the exact cam pinion profile of i-PGS with the introduction of a profile shift coefficient. Furthermore, a new root relief profile modification for the i-PGS cam pinion is presented. Then, the contact stresses are investigated to determine the characteristics of the surface fatigue by varying the shape design parameters. The results show that the contact stresses of i-PGS can be reduced significantly by increasing the profile shift coefficient. In addition, the contact ratio, a measure of teeth overlapping action, decreases with the decrease of the allowable pressure angle.