• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.5 no.2
• /
• pp.119-127
• /
• 1995

The purpose of this study was to determine the effects of surface-treatment by zinc salts on break-through and adsorption capacity of toluene. Firstly, the coconut activated carbon treated the surface with zinc salts, were exposed by the spike sample(toluene, 69.02ppm, $260.1mg/m^3$), and then the effects of zinc salts were examined by using the gas adsorption kinetics. The results obtained were as follows : 1) BET(Brumaure Emmett Teller) surface area were $954.4m^3/g$ in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$, and $830.3m^2/g$ in coconut activated carbon treated with 0.0001 N $ZnCl_2$. 2) Migration was decreased in coconut activated carbon treated with the thin level of zinc salts. 3) Breakthrough volume were 73.07 L in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$, and 72.76 L in charcoal treated with 0.0001 N $ZnCl_2$. 4) ${\tau}$ values(the time required for 50% breakthrough) were 1046.1 min in coconut activated carbon treated with 0.0001 N $ZnCl_2$ and 921.2 min in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$. 5) Maximum adsorption capacity was 53.9 mg/tube in coconut activated carbon treated with 0.0001 N $ZnCl_2$ and 47.4 mg/tube in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$. In conclusion, the coconut activated carbon treated the surface with the thin concentration of zinc salts, decreased the breakthrough and increased the BET surface area and the adsorption capacity in case of sampling airborne toluene.

• Analytical Science and Technology
• /
• v.26 no.1
• /
• pp.86-90
• /
• 2013

$^{222}Rn$ concentrations in the groundwater samples without standard material due to the short half-life (3.82 day) were measured through the establishment of the counting efficiency of LSC (Liquid Scintillation Counter) using a standard source of $^{226}Ra$. This study for Quality Assurance/Quality Control (QA/QC) of $^{222}Rn$ analysis was performed to analyze blank samples, duplicate samples, samples of groundwater sampling before and after. In-situ blank samples collected were in the range of 0.44~6.28 pCi/L and laboratory samples were in the range of 1.66~4.95 pCi/L. Their correlation coefficient was 0.9691 and the source contamination from sampling, migration and keeping of samples were not identified. The correlation coefficient between original and duplicate samples from 65 areas was 0.9987. Because radon is an inert gas, in case of groundwater sampling, it is considered to affect the radon concentration. We analyzed samples separately by groundwater sampling before and after using distilled water, but there is no significant difference for $^{222}Rn$ concentrations in distilled waters of two types.

• Journal of Environmental Health Sciences
• /
• v.46 no.2
• /
• pp.192-203
• /
• 2020

Objectives: The concentration distributions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), dioxin-like polychlorinated biphenlys (dl-PCBs), and polycyclic aromatic hydrocarbons (PAHs) in fine particles were investigated to provide basic data on POP behavior and composition analysis. Methods: The concentrations of PCDD/Fs, dl-PCBs, and PAHs by particle size were evaluated for TSP, PM₁₀, and PM_2.5. Also, fine dust component analysis and factor analysis were performed to identify the source of PCDD/Fs. Results: The particle size distribution was found to account for 24.3% of >10 ㎛, 14.5% of 2.5-10 ㎛, and 61.2% of <2.5 ㎛. The average contributions of coarse particles (>2.5 ㎛) and fine particles (<2.5 ㎛) were PCDD/Fs 67%, dl-PCBs 66%, benzo (a) pyrene 83% and PAHs 84%, and the contributions of fine particles (<2.5 ㎛) were higher than coarse particles (>2.5 ㎛). However, the contributions of coarse particles increased in April to September with higher temperatures, while those of fine particles increased in February to March with lower temperatures. Conclusions: Low chlorinated (4Cl-5Cl) PCDD/Fs were more adsorbed compared to coarse particles due to the influence of pollutant migration from particulate to gas phase according to temperature rise, whereas high chlorinated (6Cl-8Cl) PCDD/Fs were more adsorbed compared to fine particles. PCDD/Fs sources were assessed to be major sources of emissions, such as incineration facilities and/or open burning.

• Advances in Traditional Medicine
• /
• v.1 no.1
• /
• pp.8-27
• /
• 2000

Components of extracellular matrix and the matrix-degrading enzymes are some of the key regulators of tumor metastasis and angiogenesis. Hyaluronic acid (HA), a matrix glycosaminoglycan, is known to promote tumor adhesion and migration, and its small fragments are angiogenic. Until now, we have compared levels of hyaluronidase, an enzyme that degrade HA, in normal adult prostate, benign prostate hyperplasia and prostate cancer tissues and in conditioned media from epithelial explant cultures, using a substrate (HA)-gel assay and ELISA-like assay (Kim et al., unpublished results). The present review described an overall characterization of hyaluronidases and its application to human diseases. The hyaluronidases are a family of enzymes that have, until recently, deed thorough explication. The substrate for these enzymes, hyaluronan, is becoming increasingly important, recognized now as a major participant in basic processes such as cell motility, wound healing, embryogenesis, and implicated in cancer progression. And in those lower life forms that torment human beings, hyaluronidase is associated with mechanisms of entry and spread, e.g. as a virulence factor for bacteria, for tissue dissection in gas gangrene, as a means of treponema spread in syphilis, and for penetration of skin and gut by nematode parasites. Hyaluronidase also comprises a component of the venom of a wide variety of organisms, including bees, wasps, hornets, spiders, scorpions, sh, snakes and lizards. Of particular interest is the homology between some of these venom hyaluronidases and the enzyme found in the plasma membrane of mammalian spermatozoa, attesting to the ancient nature of the conserved sequence, a 36% identity in a 300 amino acid stretch of the enzyme protein. Clearly, hyaluronidase is of biological interest, being involved in the pathophysiology of so many important' human disorders. Greater effort should be made in studying this family of enzymes that have, until recently, been overlooked. Also, oriental medical application of the hyaluronidase will be discussed with respect to inhibition and suppression of inflammation and malignacy.

• Economic and Environmental Geology
• /
• v.53 no.4
• /
• pp.479-489
• /
• 2020

A fault is a geological structure that can be a migration path or a cap rock of hydrocarbon such as oil and gas, formed from source rock. The fault is one of the main targets of seismic exploration to find reservoirs in which hydrocarbon have accumulated. However, conventional fault detection methods using lateral discontinuity in seismic data such as semblance, coherence, variance, gradient magnitude and fault likelihood, have problem that professional interpreters have to invest lots of time and computational costs. Therefore, many researchers are conducting various studies to save computational costs and time for fault interpretation, and machine learning technologies attracted attention recently. Among various machine learning technologies, many researchers are conducting fault interpretation studies using the support vector machine, multi-layer perceptron, deep neural networks and convolutional neural networks algorithms. Especially, researchers use not only their own convolution networks but also proven networks in image processing to predict fault locations and fault information such as strike and dip. In this paper, by investigating and analyzing these studies, we found that the convolutional neural networks based on the U-Net from image processing is the most effective one for fault detection and interpretation. Further studies can expect better results from fault detection and interpretation using the convolutional neural networks along with transfer learning and data augmentation.

• Korean Journal of Food Science and Technology
• /
• v.32 no.3
• /
• pp.570-577
• /
• 2000

A method was presented for determination of bisphenol F(BPF), bisphenol A(BPA), bisphenol F diglycidyl ether(BFDGE) and bisphenol A diglycidyl ether(BADGE) in 3 aqueous-based food simulants (water, 4% acetic acid, 20% ethanol) by reverse-phase high performance liquid chromatography(RP-HPLC)with fluorescence detection and gas chromatography with mass selective detection(GC/MSD). All the calibration lines in the range of $5{\sim}800\;{\mu}g/L$ had correlation coefficients greater than 0.9998 and detection limits of less than $1.2\;{\mu}g$ bisphenols/L. Precision at $200\;{\mu}g/L$ was under 3.1%. Recoveries of bisphenols simultaneously spiked to aqueous food simulants exceeded 95% for BPF and BPA but about 80% for BFDGE and BADGE. However, recoveris of BFDGE and BPADGE respectively spiked increased upto 95%. Detection limits in recovery test were less than $0.40\;{\mu}g$ bisphenols/L. In migration test bisphenols were determined by RP-HPLC coupled with confirmation by GC/MSD. Can coatings of epoxy phenol, modified epoxy, epoxy ester phenol and thermoset vinyl were exposed to the 3 aqueous food simulants. BPF, BFDGE and BADGE were not detected in all the can coatings but BPA was detected in 4% acetic acid and 20% ethanol in all the can coatings except modified epoxy.

• Nuclear Engineering and Technology
• /
• v.47 no.5
• /
• pp.608-616
• /
• 2015

The migration of silver (Ag) in silicon carbide (SiC) and $^{110m}Ag$ through SiC of irradiated tristructural isotropic (TRISO) fuel has been studied for the past three to four decades. However, there is no satisfactory explanation for the transport mechanism of Ag in SiC. In this work, the diffusion coefficients of Ag measured and/or estimated in previous studies were reviewed, and then pre-exponential factors and activation energies from the previous experiments were evaluated using Arrhenius equation. The activation energy is $247.4kJ{\cdot}mol^{-1}$ from Ag paste experiments between two SiC layers produced using fluidized-bed chemical vapor deposition (FBCVD), $125.3kJ{\cdot}mol^{-1}$ from integral release experiments (annealing of irradiated TRISO fuel), $121.8kJ{\cdot}mol^{-1}$ from fractional Ag release during irradiation of TRISO fuel in high flux reactor (HFR), and $274.8kJ{\cdot}mol^{-1}$ from Ag ion implantation experiments, respectively. The activation energy from ion implantation experiments is greater than that from Ag paste, fractional release and integral release, and the activation energy from Ag paste experiments is approximately two times greater than that from integral release experiments and fractional Ag release during the irradiation of TRISO fuel in HFR. The pre-exponential factors are also very different depending on the experimental methods and estimation. From a comparison of the pre-exponential factors and activation energies, it can be analogized that the diffusion mechanism of Ag using ion implantation experiment is different from other experiments, such as a Ag paste experiment, integral release experiments, and heating experiments after irradiating TRISO fuel in HFR. However, the results of this work do not support the long held assumption that Ag release from FBCVD-SiC, used for the coating layer in TRISO fuel, is dominated by grain boundary diffusion. In order to understand in detail the transport mechanism of Ag through the coating layer, FBCVD-SiC in TRISO fuel, a microstructural change caused by neutron irradiation during operation has to be fully considered.

• Korean Journal of Bronchoesophagology
• /
• v.8 no.1
• /
• pp.29-34
• /
• 2002

Background and Objectives : Sulfur dioxide gas is one of the major airborne Pollutants noxious to human in industrialized countries. The most vulnerable areas in the human respiratory system were the trachea and main bronchi and a gradient of decreasing damage was observed in the peripheral tracheobronchial tree. Induced functional alteration was increased mucosal permeability, and morphological changes were epithelial sloughing, intracellular edema, mitochondrial swelling, widened intercellular spaces, and ciliary cytoplamic extrusions. The laminins are a family of extracellular matrix glycoproteins localized in the basement membrane. Their primary role is cell-matrix attachment, but many additional biologic activities, including Promoting cell growth and migration, tumor growth and metastasis, wound repair, and graft survival, have been demonstrated. Materials and Methods : Histologic changes and expression of laminin in tracheal mucosa sacrificed at 1 day, 2 day, 3 day, 1 week, 2 weeks, and 3 weeks after continued SO2 exposure of 250 ppm for 30 minutes a day(to 7week) were studied in rats. In this study, mild immune reaction for laminin was noted at the apical cytoplasm of epithelial cells and basement membrane one day after a 7 week $SO_2$ exposure. The cilia and nucleoi of epithelial cells were normal and no immune reaction was noted in Goblet cells. The lamina propria of the tracheal tissue was infiltrated by monocytes and lymphocytes. Results : At 24 hours after exposure, all tracheal cells except Goblet cells revealed a mild immune reaction for laminin. No immune reactions were noted in the basement membrane. At 72 hours after exposure, mild or moderate immune reactions for laminin was seen in the tracheal cell cytoplasm. Irregular faint immune reaction for laminin was noted in the basement membrane. At 1 week after exposure, strong immune reaction for laminin was detected over all tracheal cells, and the basement membrane was seen clearly. At 2~3 weeks after exposure, strong immune reaction for laminin was seen in all tracheal epithelial cells except Goblet cells and a mild immune reaction was partly revealed in the basement membrane. Conclusion : Our study suggests that 502 produces histologic damage on the tracheal mucosa. Longer duration after exposure of $SO_2$ makes more progressive healing on the tracheal mucosa and increased immunoreactivity for laminin.

• Analytical Science and Technology
• /
• v.18 no.6
• /
• pp.511-519
• /
• 2005

A method for determination of toluene diisocyanates (TDI) in toluene diisocynate (TDI)-based polyurethane (PUR) packing material was investigated, and also the migration of TDI to food was studied. TDI was extracted using food simulants such as n-haptane and 4% aqueous acetic acid. The determinations were performed using gas chromatography/mass spectrometry (GC/MS). One of major components for polyurethane, toluene diisocyanates, were detected in ten samples among twenty six food contact materials with the concentration range of $0.51{\sim}60.88{\mu}g/ml$. However the highest extracted amount was just 0.7% of $60.88{\mu}g/ml$ if the contact surface of food packing for extracting liquid was limited to the outer layer without exposure of the cutting edge of food packing multi-layers. The result of this study and the analysis method for TDI diisocyanate will be very useful for further study about food contact material, and the monitoring result could be used for evaluating the safety of food contact material before it is to be used for food, preservation.

• Journal of Welding and Joining
• /
• v.28 no.3
• /
• pp.92-98
• /
• 2010

Ferritic stainless steels, which have relatively small thermal expansion coefficient and excellent corrosion resistance, are increasingly being used in vehicle manufacturing, in order to increase the lifetime of exhaust manifold parts. But, there are limits on use because of the problem related to cosmetic resistance, corrosions of condensation and high temperature salt etc. So, Aluminum-coated stainless steel instead of ferritic stainless steel are utilized in these parts due to the improved properties. In this investigation, Al-8wt% Si alloy coated 409L ferritic stainless steel was used as the base metal during Gas Tungsten Arc(GTA) welding. The effects of coated layer on the microstructure and hardness were investigated. Full penetration was obtained, when the welding current was higher than 90A and the welding speed was lower than 0.52m/min. Grain size was the largest in fusion zone and decreased from near HAZ to base metal. As welding speed increased, grain size of fusion zone decreased, and there was no big change in HAZ. Hardness had a peak value in the fusion zone and decreased from the bond line to the base metal. The highest hardness in the fusion zone resulted from the fine re-precipitation of the coarse TiN and Ti(C, N) existed in the base metal during melting and solidification process and the presence of fine $Al_2O_3$ and $SiO_2$ formed by the migration of the elements, Al and Si, from the melted coating layer into the fusion zone.