• 전기학회논문지
• /
• 제59권9호
• /
• pp.1621-1625
• /
• 2010

Recently, due to increase in the usage of toxic gas and inflammability gas, the ability to monitor and precisely measurement of these gases is crucial in preventing the occurrence of various accidents. CuO doped and undoped $WO_3$ thick films gas sensors were prepared using screen-printing method on alumina substrates. A structural properties of $WO_3$:CuO thick films had monoclinic phase and triclinic phase of $WO_3$ together. Sensitivity of $WO_3$:CuO sensor at 2000 ppm of $CO_2$ gas and 50 ppm of $H_2S$ gas was investigated. 4 wt% Cu doped $WO_3$ thick films had the highest sensitivity of $CO_2$ gas and $H_2S$ gas.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권4호
• /
• pp.462-472
• /
• 1999

De-NOx facility using Selective Catalytic Reduction method is the most widely applied one that removes NOx from flue gas emitted from combustion facility such as boiler for power generation engine incinerator etc. Reductant $NH_3\;or\;NH_4OH$ is sprayed into flue gas to convert NOx into $H_2O$ and $N_2.$ Good mixing between flue gas and $NH_3$ is the most important factor to increase reduction in catalytic layer and to reduce unreacted NH3 slip. Therefore the development of mixer device for mixing effect is one of the important part for SCR facility. Objectives of this study are to investigate the relation between flow and concentration field by observation at the wake of delta-wing type mixer. At the first stage qualitative measurement of flow field is conducted by flow visualization using laser light sheet in lab. scale wind tunnel. Also we have conducted the quantitative analysis by comparing flow field measurement using LDV with numerical simulation. On the basis of qualitative and quantitative analysis we investigate the dis-tribution of flow and concentration in flow model facility. The results of an experimental and compu-tational examination of the vortex structures shed from delta wing type vortex generator having $40^{\circ}$ angle of attack are presented, The effects of vortex structure on the gas mixing is discussed, too.

• Tribology and Lubricants
• /
• 제37권5호
• /
• pp.164-171
• /
• 2021

Ultrasonic sensors show various reception characteristics based on the density of the measurement medium; hence, they are used in various fields to benefit from the characteristics of ultrasonic signals. In this study, the reception characteristics according to the thickness of the first matching layer are compared and analyzed for application to gas tank microleak detection. Accordingly, three types of sensors are manufactured with varying thicknesses of the first matching layer, namely 4.8 mm, 5.1 mm, and 5.5 mm; further, a direct measurement method is used wherein the sensor is attached to the inside of the chamber. Experiments are conducted to observe the phase change due to microleakage, which is the most linear in the sensor with the 4.8 mm thick first matching layer. This is assumed to be the result of stable signal transmission and reception with little phase deviations over time because the first matching layer is closest to the ultrasonic wavelength. The other sensors show nonlinear results with increasing thickness of the first matching layer. Through this study, it is found that appropriately selecting the thickness of the first matching layer of the ultrasonic sensor can greatly influence sensor reliability.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 추계학술발표 개요집
• /
• pp.111-114
• /
• 1994

This paper describes a method to measure a weldment surface temperature for estimating variations of the weld pool size in the gas metal arc(GMA) welding processes. An Infrared sensing system is designed to measure the radiation emitted from the top surface of the weldment, The interference effect of the electric arc to the measurement is rejected by detecting the low peaks of the noisy signal. An optimizing criterion, in which the correlation between the weld quality and the measured temperature is maximized, is also proposed to determine the optimal measurement location.

• 한국가스학회지
• /
• 제24권5호
• /
• pp.29-38
• /
• 2020

산업현장의 대형 연소시스템 내부의 온도 및 농도를 실시간으로 정밀하게 계측하는 일은 그 규모 및 환경 조건으로 인해 사실상 어렵다. 현재 주로 사용되고 있는 열전대를 이용한 온도 계측은 점 측정 방식으로 대형 연소시스템 내부 광역 범위의 온도 분석에 적용하기에는 정밀성과 신뢰성이 낮으며, 접근성에 한계가 있다. 농도 분석 측면에서 대부분의 계측 방법은 샘플링 방식으로 실시간 측정이 어렵고 대표성에 한계가 있다. 이러한 한계점을 극복하기 위한 방법으로, 레이저를 이용한 측정법이 지속적으로 개발되고 있다. 레이저 기반 측정법들은 선 평균 측정 방식으로 대표성과 정밀도가 뛰어나 대형 연소시스템 적용에 유리하다. 본 연구에서는 파장 가변형 레이저 흡수 분광법(Tunable Diode Laser Absorption Spectroscopy, TDLAS)을 통해 연소 시에 발생하는 수증기와 산소를 이용하여 실시간으로 온도 및 농도를 측정하였다. 측정 결과 연소시스템 내부 평균 온도는 1330℃, 평균 산소 농도는 3.3 %로 발전소 데이터와 비교하였을 때 유사한 경향성의 측정값을 얻었다.

• Journal of the Optical Society of Korea
• /
• 제19권4호
• /
• pp.415-420
• /
• 2015

A novel method to measure the scale factor for the all-optical atomic spin inertial measurement device (ASIMD) is demonstrated in this paper. The method can realize the calibration of the scale factor by a self-consistent method with small errors in the quiescent state. At first, the matured IMU (inertial measurement unit) device was fixed on an optical platform together with the ASIMD, and it has been used to calibrate the scale factor for the ASIMD. The results show that there were some errors causing the inaccuracy of the experiment. By the comparative analysis of theory and experiment, the ASIMD was unable to keep pace with the IMU. Considering the characteristics of the ASIMD, the mismatch between the driven frequency of the optical platform and the bandwidth of the ASIMD was the major reason. An all-optical atomic spin magnetometer was set up at first. The sensitivity of the magnetometer is ultra-high, and it can be used to detect the magnetization of spin-polarized noble gas. The gyromagnetic ratio of the noble gas is a physical constant, and it has already been measured accurately. So a novel calibration method for scale factor based on the gyromagnetic ratio has been presented. The relevant theoretical analysis and experiments have been implemented. The results showed that the scale factor of the device was $7.272V/^{\circ}/s$ by multi-group experiments with the maximum error value 0.49%.

• 한국가스학회지
• /
• 제3권2호
• /
• pp.62-69
• /
• 1999

본 논문에서는 혼합감도문제를 이용하여 강인한 서보계를 구성함으로서 동위치 제어 시스템의 제어계를 설계하는 방법을 제안하였고, LQG를 이용한 다변수 디지털 서보 제어기 및 H$\infty$ 최적 제어기와의 비교실험을 통하여 제안된 제어기의 유용성을 입증하였다.

• 한국정보전자통신기술학회논문지
• /
• 제7권4호
• /
• pp.200-204
• /
• 2014

가정에서 사용하는 LPG는 용량을 측정할 수 있는 방법이 없기 때문에 공급자에 의존할 수밖에 없었다. 또한 LPG 가스 교체 시기를 알 수 없기 때문에 가스 용량을 측정하여 교체시기에 대한 경보를 필요로 하고 있다. 본 연구에서는 사용자와 공급자가 믿고 신뢰할 수 있는 있도록 가스통을 교체할 시기를 알려 주고, 공급가스 용량을 쉽게 알 수 있도록 하기 위해 홀 효과 센서를 적용하여 가스 용량 측정 밸브 시스템을 개발하였다.

• Journal of Radiation Protection and Research
• /
• 제31권3호
• /
• pp.149-153
• /
• 2006

An ionization chamber is still widely used in many fields by virtue of its' simple operational characteristics and the possibility of its' various shapes. A parallel type of an ionization chamber for a steel sheet thickness measurement was designed and fabricated. High pure xenon gas, which was pressurized up to 6 atm, was chosen as a filling gas to increase the current response and sensitivity for a radiation. A high pressure gas system was also constructed. The active volume and the incident window size of the fabricated ionization chamber were $30\;cm^3\;and\;12\;cm^2$, respectively. Preliminary tests with a 25 mCi $^{241}Am$ gamma-ray source and evaluation tests in a standard X-ray field were performed. The optimal operation voltage was set from the results of the collection efficiency calculation by using an experimental two-voltage method. Linearity for a variation of the steel sheet thickness, which is the most important factor for an application during a steel sheet thickness measurement, was 0.989 in this study.

• 한국해양공학회지
• /
• 제35권1호
• /
• pp.59-74
• /
• 2021

To validate the fire safety assessment of structures, many structural experiments under fire load have been conducted. However, most of these experiments were conducted in restricted environments, such as inside a furnace, and experiments were seldom carried out in open space. In this study, an experimental study on H-beams, frequently used as structural reinforcements, was carried out for validating the thermal-structural analysis method under development. A 1.8 MW burner fire was adopted with each end of the H-beam fixed without a mechanical load. Gas temperature, steel surface temperature, and displacements were then measured. During the experiment, gas and steel temperatures were obtained at 9 and 17 points near the H-beam, respectively. In addition, the vertical and horizontal displacements of the H-beam under fire load at 6 points were obtained. Furthermore, it was verified that the stable displacement measurements via the contact and non-contact methods were feasible in harsh environments where flames and smoke were both present.