• Journal of the Korean Institute of Gas
• /
• v.23 no.5
• /
• pp.1-7
• /
• 2019

Although the rupture pressure is evaluated from remaining strength when a flaw is defected to cylinder surface, but the rupture pressure can be not easy to estimate for the composite cylinders. In this study, the area capacity method is developed for the type-3 cylinders that is based on the result applied area capacity method of type-1 cylinders. And the reliability is validated by bursting test with artificial flaw at the cylinder surface. The predicted data of area capacity method and experimental results have very similar tendency. This method and results will be a very important records in field of rupture pressure estimations.

• Journal of the Korean Institute of Gas
• /
• v.13 no.2
• /
• pp.41-48
• /
• 2009

I collected the cases of CNG vehicle accidents which had happened for 30 years and analyzed the causes of the accidents according to each type of cylinders. There are about six accidents including three cylinder explosion accidents due to bad heat treatment, one composite damage, one CNG vehicle fire, and one fuel piping accident owing to the poor maintenance. When looking into the cylinder types involved in the accidents and the causes, 29% of the cylinder accidents are Type I and 24% Type IV, 16% Type II, and 14% Type III. 37% of the accidents are caused by the defects of the raw materials and the errors of a manufacturing process, 16% by the stress corrosion cracking as a result of the repetitive use, 15% by the cylinder's explosion on account of the malfunction of PRD(Pressure Relief Device) and the overpressure. The remainders of the causes are fire and unknown causes. Therefore, cylinder manufacturers have to strengthen quality management of raw materials and manufacturing process and painting regardless of each type of cylinder. Also bus operators need to make an effort to keep safety condition through every day check.

• Journal of the Korean Institute of Gas
• /
• v.22 no.2
• /
• pp.72-77
• /
• 2018

This paper presents the FEM analysis results on the strength safety of LPG fuelling nozzle, which is composed of ball valve and long cylinder tube. For the strength safety analysis of LPG fuelling Nozzle, the gas pressure of 0.5~3.5MPa has been supplied to the ball valve and long cylinder tube bodies with the wall thickness of 1.7~3.5mm. The maximum von Mises stress of the ball valve with 1.7mm wall thickness is 25.4MPa for the supply gas pressure of 3.5MPa, which is 25.9% compared with that of the yield stress of the brass. And the maximum von Mises stress was 23.7MPa when a 3.5MPa gas pressure was applied to a long cylinder tube with a wall thickness of 1.7mm, which was 6.7% more safe than the ball valve which was analyzed under the same conditions. For the increased wall thickness, 2.0mm of the long cylinder tube, the maximum von Mises stress of 20.2MPa is 14.8% more safe compared with that of 1.7mm wall thickness of the same cylinder tube. Thus, the wall thickness of the ball valve and cylinder tube is recommended as an optimized thickness of 1.7~2.0mm for the strength safety of the LPG fuelling nozzle.

• 한국가스학회:학술대회논문집
• /
• 2000.09a
• /
• pp.87-94
• /
• 2000

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.16-21
• /
• 2003

Natural gas is one of the promising alternative fuels because of the abundant deposits and the cleanness of emission gas. It can be used in conventional gasoline engine without major modification. Natural gas has some advantages than gasoline i.e. the high octane number, good mixing condition because of gas and wide inflamable limit. In the present study, a $1.8{\ell}$ conventional gasoline engine is modified for using the CNG as a fuel instead of gasoline. Performance and emission characteristics are compared between gasoline and CNG with 4 cylinder SI Engine which is controlled by programable ECU. Parameters of experimentation are equivalence ratio, spark timing and fuels. We analyzed the combustion characteristics of the engine using the cylinder pressure i.e. ignition delay, combustion duration and cycle variation. As a result, CNG engine shows lower exhaust emissions but brake torque is slightly reduced compared to gasoline engine. Overall combustion duration is longer than that of gasoline because of lower burning speed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.4
• /
• pp.267-275
• /
• 2001

To clear the differences of heat transfer coefficient of in-cylinder gas with fuel properties, the transient heat transfer coefficient of hydrogen gas is investigated by using the hydrogen fueled engine. The measured results were also compared with those of gasoline engine and several empirical equations. Transient heat transfer coefficients were determined by measurements of unsteady heat flux and instantaneous wall temperature in the cylinder head. As the main results, it is shown that transient heat transfer coefficients have remarkable differences according to fuel properties, and it's value for hydrogen engine is twice higher than that of gasoline engine. It means that equation of heat transfer coefficient that the effect of fuel properties is considered sufficiently, is needed to analyze or simulate the gas engine performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.79-86
• /
• 2000

The effects of recirculated exhaust gas on the wears of piston and piston rings were investigated by the experiment with a two-cylinder, four cycle, indirect injection diesel engine operating at an engine load of 75% and an engine speed of 1600 rpm. For the purpose of comparison between the wear rates of two cylinders with and without EGR, the recirculated exhaust gas was sucked into one of two cylinders after the soot contenets in exhaust emissions were removed by an intentionally designed cylinder-type scrubber equipped with 6 water injectors(A water injector has 144 nozzles of 1.0 mm diameter), while only the fresh air was inhaled into the other cylinder. These experiments were carried out on the fuel injection timing fixed at 15.3$^{\circ}$ BTDC. It was found that the wear rate of piston skirt with EGR increased a little bit, but the piston head diameter increased, rather than decreased, owing to soot adhesion and erosion wear, and especially larger with EGR, and that the wear rates of the top and second piston ring(compression ring)thickness with EGR were more than twice the wear rate of top ring in case of no EGR, but the wear rate of oil rings thickness without EGR increased greater than that with EGR.

• Journal of the Korean Institute of Gas
• /
• v.19 no.6
• /
• pp.80-84
• /
• 2015

In this paper, the valves for a LPG gas cylinder have been investigated on the body height and weight by comparing design data between typical automatic shut-off vertical and newly developed horizontal valves. The height of an automatic shut-off horizontal valve is radically reduced by 41~42% compared with that of a typical automatic shut-off vertical valve. And, the body weight of a horizontal valve is also reduced by 29~40% compared with that of a vertical shut-off valve. This result is just achieved by a structural design modification from typical vertical valve to horizontal arrangement of various valve components.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.5
• /
• pp.402-410
• /
• 2008

The heavy duty diesel engine must have a large output for maintaining excellent mobility. In this study, a three dimensional finite element model of a heavy-duty diesel engine was developed to conduct the stress analysis. The FE model of the heavy duty diesel engine main parts consisting with four half cylinder was selected. The heavy duty diesel engine parts includes with cylinder block, cylinder head, gasket, liner, bearing cap, bearing and bolts. The loading conditions of engine were pre-fit load, assembly load, and gas load. As the results of structural analysis, because the stress values of cylinder block and bearing cap did not exceed the basic design can be satisfied. But on the part which contacts with cylinder block and bearing cap the stress value exceeds the allowable strength of material. In order to decrease the stress at that part, it was optimized with parametric study.

• 한국가스학회:학술대회논문집
• /
• 2000.09a
• /
• pp.137-142
• /
• 2000