• 설비공학논문집
• /
• 제18권2호
• /
• pp.180-185
• /
• 2006

This study has been conducted in order to develop a temperature-controlled round pan diffuser with variable-openings. Flow visualization was performed to investigate the airflow patterns according to gap openings. The velocity profiles were measured using an omni-directional anemometer for two cases, i.e. a horizontal and a vertical discharge conditions. Numerical simulation also confirms there is a narrow range of gap openings where a horizontal discharge shifts to a vertical discharge. The air distribution performance index increases abruptly when the air discharge shifts from vertical to horizontal direction.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.387-392
• /
• 2003

This study is put a focus on the identification of sound characteristics according to the interior configuration of sound absorption material and air gap. Noise barrier is general consists of front perforated panel, air layer, sound absorption material, air gap and back plate. Noise barrier is required to the NRC value of 0.7. The absorbing performance of the noise barrier relies on the opening ratio of the perforated panel and the efficiency of the absorbing material. This study has observed the effect of opening ratio and hole size, the increase of sound absorbing performance by the configurations of sound absorption material and air gap. New designed noise barrier is achieved the acoustical performance of 0.87 the measurement in a reveration room.

• 한국유체기계학회 논문집
• /
• 제15권6호
• /
• pp.5-10
• /
• 2012

The effect of pressure-side opening length on three-dimensional flow fields and aerodynamic losses downstream of a cavity squealer tip has been investigated in a turbine rotor cascade for the squealer rim height-to-chord ratio and tip gap height-tochord ratio of $h_{st}/c$ = 5.05% and h/c = 2.0% respectively. The opening length-to-camber ratio is changed to be $OL/c_c$ = 0.0, 0.1, 0.2, 0.3, 0.4, 0.5, and 0.7 The results show that longer OL leads not only to weaker secondary flow but also to lower aerodynamic loss in the tip leakage vortex region, while it significantly widens the area with high aerodynamic loss in the passage vortex region. The aerodynamic loss coefficient mass-averaged all over the measurement plane is kept almost constant for $0.0{\leq}OL/c_c{\leq}0.3$, whereas it increases rapidly for $OL/c_c$ > 0.3 in proportion to $OL/c_c$. There is little deterioration in flow turning with increasing $OL/c_c$.

• 대한정형외과학회지
• /
• 제55권2호
• /
• pp.127-134
• /
• 2020

목적: 이 연구의 목적은 동종 쐐기 골편의 성상과 최대압축하중과의 관계를 알아보고 동종 쐐기 골편의 최대압축하중과 경골 근위부 개방 절골술 시 측정된 개방부의 압력을 비교하는 것이다. 대상 및 방법: 경골 근위부 개방 절골술을 시행하기 전 연구에 동의한 10명의 환자가 본 연구에 포함되었다. 수술 중 절골 부위를 8 mm에서 14 mm까지 개방시키면서 1 mm 간격으로 개방부의 압력을 측정하였다. 대퇴골, 경골 및 상완골에서 U자형 동종 쐐기 골편을 채취하여 골편의 높이, 폭, 단면적 및 피질골의 두께를 측정한 뒤에 골편이 파괴되기 직전의 최대압축하중을 측정해 골편의 성상과 최대압축하중과의 관계를 평가하였다. 경골 근위부 개방 절골술 시 별도의 신연장치 없이 개방부에 동종 쐐기 골편을 삽입할 수 있는지 평가하기 위해 경골 근위부 개방 절골술 시 측정된 개방부 압력과 동종 쐐기 골편의 최대압축하중을 비교하였다. 결과: 경골 근위부 개방 절골술 중 절골부를 많이 개방할수록 개방부 압력이 증가해 14 mm 개방하였을 때 개방부의 압력(평균 282±93 N, 최대 427 N)이 가장 크게 측정되었다. 동종 쐐기 골편의 최대압축하중은 평균 13,379±6,469 N (최소값 5,868 N, 최대값 29,130 N)으로 측정되었으며 피질골의 두께(상관계수=0.693, p=0.002) 및 단면적(상관계수=0.826, p<0.001)과 유의한 상관관계를 가지고 있었다. 살균 방법에 따라 동결 건조(freeze-dried) 골편은 평균 13,406±5,928 N (최소값 5,868 N, 최대값 25,893 N), 동결(fresh frozen) 골편은 평균 13,348±7,449 N (최소값 5,916 N, 최대값 29,130 N)으로 측정되었다. 동종 쐐기 골편의 최대압축하중 최소값은 경골 근위부를 14 mm까지 개방하였을 때 측정된 개방부의 최대압력에 비해 13.7배 높았다(5,868 N vs. 427 N). 결론: 동종 쐐기 골편의 최소 압축 강도는 경골 근위부 개방 절골술 시 측정된 개방부의 최대 압력보다 충분히 큰 것으로 확인되었다. 따라서 경골 근위부 개방 절골술 중 별도의 신연장치 없이 동종 쐐기 골편을 개방부에 안전하게 삽입 가능한 것으로 판단된다.

• Journal of Welding and Joining
• /
• 제19권2호
• /
• pp.98-103
• /
• 2001

Root gap out of standard by welding deformation is frequently produced at butt weld joints of steel bridge. For example although standard root gap is below 6mm at butt weld joints of plates under 15mm thickness. maximum 35mm root opening is produced at the weld field. At this case, the part out of standard is generally built up and the rest part is welded by WPS. Direct welding without built-up welding is preferred in weld field because built-up welding process bring about the cost-up at manufacturing. To apply this direct weld to root gap out of standard, the investigation about mechanical properties and fatigue at weldment is required. Inthisstudy, therefore the verification for direct weld without built up is performed at weldment as root gap. It includes tension, bending. hardness, impact and fatigue test for each welding specimen of 6mm, 25mm, 35mm root gap.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.442-442
• /
• 2011

Electronic and magnetic properties of bilayer zigzag graphene nanoribbon (bZGNR) are studied using pseudopotential density functional method. The edge atoms in the top and bottom layers of bZGNR make a weak hybridization, which leads to electronic structures different from monolayer ZGNR. For asymmetric bZGNR, where the top and bottom layers have different widths, one edge is pinched by the interlayer bonding and the other sustains antiferromagnetic ordering. A small amount of charge transfer occurs from narrower to wider layer, producing spin-polarized electron and hole pockets. External electric field produces asymmetric energy-gap opening for each spin component, inducing half-metallicity in bZGNR.

• 소성∙가공
• /
• 제9권6호
• /
• pp.624-630
• /
• 2000

Typical automotive opening parts, i. e. hood trunk lid and door, are made through the press operations such as drawing, trimming, flanging, and hemming. The dimensional accuracy of stamped panels is mainly dependent on the drawing operation. However, the gap between outer panels and opening parts, which is important to the appearance quality of the assembled body, is directly influenced by the flanging and hemming operation. In this study, the relation between the design parameters of the hemming operation and the defect of roll-in is shown. The effects of some design parameters on the gap are examined using CAE. furthermore, the simulated results of the hemmed part of tailgate comer are shown and discussed.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.74-82
• /
• 2002

In Intensity Modulated Radiotherapy (IMRT), radiation is delivered in a multiple of Multileaf Collimator (MLC) subfields. A subfield with a small leaf-to-leaf opening is highly sensitive to a leaf-positional error. We introduce a method of identifying and rejecting IMRT plans that are highly sensitive to a systematic MLC gap error (sensitivity to possible random leaf-positional errors is not addressed here). There are two sources of a systematic MLC gap error: Centerline Mechanical Offset (CMO) and, in the case of a rounded end MLC, Radiation Field Offset (RFO). In IMRT planning system, using an incorrect value of RFO introduces a systematic error ΔRFO that results in all leaf-to-leaf gaps that are either too large or too small by (2ㆍΔRFO), whereas assuming that CMO is zero introduces systematic error ΔCMO that results in all gaps that are too large by ΔCMO = CMO. We introduce a concept of the Average Leaf Pair Opening (ALPO) that can be calculated from a dynamic MLC delivery file. We derive an analytic formula for a fractional average fluence error resulting from a systematic gap error of Δ$\chi$ and show that it is inversely proportional to ALPO; explicitly it is equal to, (equation omitted) in which $\varepsilon$ is generally of the order of 1 mm and Δx=2ㆍΔRFO+CMO. This analytic relationship is verified with independent numerical calculations.

• 공업화학
• /
• 제31권3호
• /
• pp.267-276
• /
• 2020

Oxirane계 단량체의 양이온 개환 공중합반응으로 합성되는 ECH (ephichorohydrin) 기반 copolyol (PECH copolyol)류의 특성에 대한 반응온도, 용매의 종류 및 개시제에 대한 영향을 연구하였다. 공단량체로는 butylene oxide와 hexylene oxide 두 종류의 알킬렌 옥사이드를 사용하였으며, 중합 조건은 methylene chloride (MC) 용매에서 개시제로 diethylene glycol (DEG)를 사용한 조건과 toluene을 용매에서 tripropylene glycol (TPG)를 개시제로 사용한 두 조건으로 진행하였다. 개환 공중합반응에서 active monomer (AM) mechanism 유도를 위해 단량체는 실린지 펌프를 사용해 IMA (increased monomer addition) 방법으로 주입하였고 중합온도는 -5 ℃에서 실행하였다. 합성된 ephichorohydrin (ECH) 기반 copolyol인 PECH copolyol은 치환반응으로 ECH unit를 아지드화하여 glycidyl azide계 에너지 함유 copolyol (GAP copolyol)로 전환하였다. 합성된 아지드화 코폴리올은 용매와 개시제의 변화에 대한 영향은 크지 않았으며, 분자량은 아지드화 반응 후 평균 500 증가함으로써 GAP 코폴리올이 설계한 대로 중합되었음을 확인하였다. DSC 분석으로 copolyol류의 조성비 변화에 따른 유리전이 온도(glass transition temperature, T_g)의 변화를 측정하였을 때, 공단량체의 함량이 증가할수록 알킬 사슬의 길이에 의한 영향으로 T_g와 점도가 모두 감소하는 경향을 보였다. 아지드화 반응과정에서 생성되는 CH₃N₃의 생성을 원천적으로 방지할 수 있으며, 대규모 공정이 가능할 것으로 기대된다.

• 설비공학논문집
• /
• 제30권4호
• /
• pp.195-203
• /
• 2018

Mohair is widely used as an airtight material for filling the gap between a window frame and sash. The purpose of this study is to investigate infiltration rate and opening force of sliding windows according to the mohair installation conditions. Infiltration experimental apparatus was set up, and the experimental results were applied to windows to find a correlation between infiltration rates and opening forces. When 4 rows of mohair were installed, the infiltration rate increase became 27.1% per clearance length increase of 1 mm, and the infiltration rate decrease became 5.7% per shortened length increase of 0.1 mm. For 4 rows of mohair, the opening force decreased by 28.2% as the clearance increased by 1 mm, and it increased by 9.3% as the shortened length increased by 0.1 mm.