• Computers and Concrete
• /
• 제26권2호
• /
• pp.161-173
• /
• 2020

Shear keys in precast concrete segmental bridges (PCSBs) are usually match-casting which is very labour intensive. In this research, an innovative match-casting-free construction was proposed by leaving small gap between the convex and the concave castellated shear keys in the joints of PCSBs. Specimen experiment, shear strength analysis and numerical simulation were conducted, investigating the loading performance of this new type of dry joints, the gap dry joints. Compared with match-casting joint specimens, it has been found from experiment that shear capacity of gap joint specimens significantly decreased ranging from 17.75% to 42.43% due to only partially constrained and contacted in case of gap dry joints. Through numerical simulation, the effects of bottom contacting location, the heights of the gap and the shear key base were analyzed to investigate strength reduction and methods to enhance shear capacity of gap joint specimens. Numerical results proved that shear capacity of gap dry joints under full contact condition was higher than that under partial contact. In addition, left contact destroyed the integrity of shear keys, resulting in significant strength reduction. Larger shear key base remarkably increased shear capacity of the gap joint. Experimental tests indicated that AASHTO provision underestimated shear capacity of the match-casting dry joint specimens, while the numerical results for the gap dry joint showed that AASHTO provision underestimated shear capacity of full contact specimens, but overestimated that of left contact specimens.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1071-1072
• /
• 2006

Maglev using EMS becomes unstable by unexpected big air-gap disturbance. The main causes of the unexpected air-gap disturbance are step-wise rail joint and large distance between rail splices. For the stable operation of the Maglev, the conventional system uses the threshold method, which selects one gap sensor among two gap sensors installed on the magnet to read the gap between magnet and guide rail. But the threshold method with a wide bandwidth makes the discontinuous air-gap signal at the rail joints because of the offset in air gap sensors and/or the step-wise rail joins. Further more, in the case of the one with a narrow bend-width, it makes Maglev system unstable because of frequent alternation. In this paper, a new method using fuzzy rule to reduce air-gap disturbances proposed to improve the stability of Maglev system. It treats the air-gap signal from dual gap sensors effectively to make continuous signal without air gap disturbance. Simulation and experiment results proved that the proposed scheme was effective to reduce air-gap disturbance from dual gap sensors in rail joints.

• KCI Concrete Journal
• /
• 제13권1호
• /
• pp.27-34
• /
• 2001

This paper presents the results of a study on the effects of pounding at expansion joints of concrete bridges under earthquake ground motions. An engineering approach, rather than continuum mechanics, is emphasized. First, the sensitivity analysis of the gap element stiffness is performed. Second, usefulness of the analysis method for simulation of pounding phenomena is demonstrated. Third, the effects of pounding on the ductility demands measured in terms of the rotation of column ends are investigated. Two-dimensional FE analysis using a bilinear hysterestic model for bridge substructure joints and a nonlinear gap element for the expansion joint is performed on a realistic bridge with an expansion joint. Effects of the primary factors on the ductility demand such as gap sizes and characteristics of earthquake ground motion are investigated through a parametric study. The major conclusions are that pounding effect is generally negligible on the ductility demand for wide practical ranges of gap size and peak ground acceleration, but is potentially significant at the locations of impact.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.950-955
• /
• 2005

This paper describes an intelligent filler wire feeding device which can control 3- dimensional seam tracking and the filler wire speed by measuring the gap position and the joint gap width in laser welding. By means of visual sensor controlled filling the missing material into the joint gap and 3 dimensional seam tracking, lineup errors from manufacturing tolerances and the repeatability of lineup jigs and weld robot can be balanced and at an even seam quality which avoids weld defects. In this paper, we assessed weld quality in 2mm sheets of A16061 which had various gap width by using the intelligent filler wire feeding device.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.102-111
• /
• 2017

An automobile ball joint is the element for connecting the control arm and the knuckle arm, allowing rotational motion. The ball joint consists of the stud, plug, socket, and seat. These components are assembled through the caulking process that consists of plugging and spinning. In the existing research, the pull-out strength and gap stiffness were calculated, but we did not consider the uncertainties due to the numerical analysis and production. In this study, the uncertainties of material property and tolerance are considered to predict the distributions of pull-out strength and gap stiffness. Also, pull-out strength and gap stiffness are predicted as the a distribution rather than one deterministic value. Furthermore, a robust design applying the Taguchi method is suggested.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.310-312
• /
• 2006

Maglev using EMS becomes unstable by unexpected big air-gap disturbance. The main causes of the unexpected air-gap disturbance are step-wise rail joint and large distance between rail splices. For the stable operation of the Maglev, the conventional system uses the threshold method, which selects one gap sensor among two gap sensors installed on the magnet to read the gap between magnet and guide rail. But the threshold method with a wide bandwidth makes the discontinuous air-gap signal at the rail joints because of the offset in air gap sensors and/or the step-wise rail joins. Further more, in the case of the one with a narrow bend-width, it makes Maglev system unstable because of frequent alternation. In this paper, a new method using fuzzy rule to reduce air-gap disturbances proposed to improve the stability of Maglev system. It treats the air-gap signal from dual gap sensors effectively to make continuous signal without air gap disturbance. Simulation and experiment results proved that the proposed scheme was effective to reduce air-gap disturbance from dual gap sensors in rail joints.

• Journal of Welding and Joining
• /
• 제34권1호
• /
• pp.68-74
• /
• 2016

Adoption of narrow gap welding shall be increased for the butt joint of thick plate, because the deformation and welding cost is reduced by decrease of cross-sectional area. However, sometimes narrow gap causes defects such as lack of fusion since it has small groove angle and narrow groove width. Therefore, GMAW, GTAW and SAW process shall be adopted to narrow gap welding with small bead hight and low deposition rate. In this study, Super-TIG welding using C-type strip was applied to semi-narrow gap butt joint in order to increase the welding productivity. High deposition rate 10kg/hr was obtained by high current 600A without undercut, humping bead and other welding defects. Measuring the mean and standard deviation of the melting depth to evaluate the developed processes, the fusion line type was determined by measuring the difference between maximum and minium melting depth. Furthermore, a model on arch fusion line and linear fusion line was suggested in order to prevent LF on groove wall in narrow gap butt welding.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1077-1082
• /
• 2011

볼 조인트는 두 요소 사이에서 회전 및 이동이 원활하도록 돕는 역할을 하는 기계요소이다. 본 연구의 대상인 볼 조인트는 중대형 승용차량용 볼 조인트로서 너클과 컨트롤 암의 운동을 돕는다. 본 연구에서는 볼 조인트의 공정 및 시험에 관한 해석 방법을 제안하고자 한다. 볼 조인트의 제작공정은 플러깅 공정과 스피닝 공정으로 나눌 수 있다. 볼 조인트의 제작공정 및 성능시험을 암시적 수치 적분법을 적용한 상용 동역학 프로그램인 NX DAFUL 2.0 을 사용하여 해석하였다. 또한 설계요구조건을 정의하기 위하여 볼 스터드에 작용하는 응력의 평균 및 분산을 반응치로 설정하였다. 그리고 완성된 볼조인트의 유격량을 시험하는 유격시험해석을 통해 최적의 설계를 제안하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.2020-2022
• /
• 2000

The cross-linked polyethylene(herein after XLPE) insulated power cable emit the methane($CH_4$)gas in the course of chemical cross-linking process. The general stranded conductor easily discharge this methane gas through the gap of each stranded wires. But the special stranded conductor that filled with semi-conducting rubber compound to prevent water penetration which is applied to water proof type of cable(22.9kV CN/CV-W), disturb the methane gas emission. The pre-mold type cable joint shall be expanded gradually by emit of gas left in XLPE insulation. For example, sometimes the corona problem outbreak on a new power distribution line, resulted from the gap between the sleeve and semi-conductive layer of cable joint. If above mentioned problem especially happened on the way of operating. We have to shut down the line and try to discharge the methane gas in cable joint. In this point, we would like to explain the mechanism of methane gas & cable joint and our test result briefly. At last, we are pleased to introduce the solution for preventing reoccurrence of this problem.

• 대한족부족관절학회지
• /
• 제10권1호
• /
• pp.42-47
• /
• 2006

Purpose: This study was performed to analyze the characteristics of calcaneocuboid joint involvement in intraarticular calcaneal fractures. Materials and Methods: Total number of 92 patients (111 cases) who underwent operation for intraarticular calcaneal fractures between Jan. 2000 and Oct. 2005 were included in this study. The preoperative computed tomographs of the subjects were retrospectively reviewed to analyze calcaneocuboid joint involvement. Results: It was revealed that 63 cases (56.8%) involved calcaneocuboid joint; 29cases (46.0%) showed type 1 (undisplaced or minimally displaced type, articular gap ${\le}1\;mm$), 16 cases (25.4%) exhibited type 2 (moderately displaced type, articular gap ${\ge}2\;mm$), 7 cases (11.1%) were included in type 3 (comminuted type) and 11 cases (17.5%) belonged to type 4 (fracture and dislocation). 48 out of 63 cases belonged to Sanders classification II and III that involved calcaneocuboid joint and included 25 cases (52.1%) of type 1 and 14 cases (29.2%) of type 2. Among 15 out of 63 cases included in Sanders classification IV, 4 (26.7%) showed type 1 and 6 (40.0%) belonged to type 4. According to our results, Sanders classification allowed to predict pattern of the involvement of calcaneocuboid joint (P<0.05). However, there was no statistically significant relationship between degree of posterior facet joint injuries and calcaneocuboid joint involvement (P>0.05). Conclusion: Calcaneocuboid joint involvement in intraarticular calcaneal fractures was common and more than half showed severe injuries. We concluded that further studies on the involvement of calcaneocuboid joint should be performed prior to surgical treatment of intraarticular calcaneal fractures.