• Journal of Astronomy and Space Sciences
• /
• v.18 no.1
• /
• pp.71-80
• /
• 2001

The threshold voltage shift observed in TDE (Total Dose Experiment) on board the KITAT-1 is converted into dose (rad($SiO_2$)) using the result of laboratory calibration with Co-60 gamma ray source in KAERI (Korea Atomic Energy Research Institute). Simulation using the NASA radiation model of geomagnetosphere verifies that the dose difference between RADFET1 and RADFET3 observed on KITSAT-1 comes from the difference in shielding thickness at the position of these RADFETs.

• Nuclear Engineering and Technology
• /
• v.38 no.5
• /
• pp.405-410
• /
• 2006

Microstructural features and their related mechanical property changes in the 309L cladding and the heat affected zone (HAZ) of SA508 cl.3 steel were investigated through the use of TEM, tensile and small punch (SP) tests. The specimens were irradiated at 563 K up to the neutron fluences of $5.79{\times}10^{19}n/cm^2$ (>1MeV). The microstructure of the clad was mainly composed of a fcc ${\gamma}-phase$, a low percentage of bcc ${\delta}-ferrite$, and a brittle ${\sigma}-phase$. Along the weld fusion line there formed a heavy carbide precipitation with a width of $20{\sim}40{\mu}m$, showing preferential cracking during plastic deformation. The yield stress and ductile-to-brittle transition temperature (DBTT) of the irradiated clads increased. The origin of the hardening and the shift of the DBTT are discussed in terms of the irradiation-produced defect clusters of a fine size and brittle ${\sigma}-phase$.

• 한국가스학회:학술대회논문집
• /
• 2005.10a
• /
• pp.83-87
• /
• 2005

The kinetics of the direct synthesis of DME was studied under different conditions over a temperature range of $220\~280^{\circ}C$, syngas ratio $1.2\~ 3.0$ All experiment were carried out over hybrid catalyst, composed to a methanol synthesis catalyst (Cu/ZnO/$Al_2O_3$) and a dehydration Catalyst ($\gamma$-Al_2O_3$) The observed reaction rate qualitatively follows a Langmiur-Hinshellwood type of reaction mechanism. Such a mechanism is considered with three reaction, methanol synthesis, methanol dehydration and water gas shift reaction. From a surface reaction with dissociative adsorption of hydrogen, methanol and water, individual reaction rate was determined

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.876-880
• /
• 2001

The supported and unsupported boehmite ($\gamma$-AlOOH) membranes were prepared using a boehmite sol. The supported membrane was consisted of a porcelain support, two intermediate $\alpha-{Al_2}{O_3}$ layers, and a top boehmite membrane. XRD patterns showed that the supported top membrane had a higher $\theta-$ to $\alpha-{Al_2}{O_3}$ transformation temperature compared to the unsupported membrane. This result was also confirmed from microstructural study of the membrane. The shift in the phase transformation temperature should be explained by difference of a stress generated in the supported top membrane due to interaction between the support layers and the top membrane.

• 한국기계연구소 소보
• /
• s.16
• /
• pp.29-39
• /
• 1986

Several heat treatment were applied to on HSLA steel of type StE47 (German standard) to produce five ferrite microstructures of different strength and at least two different grain sizes respectively. Whereas the ferrite microstructure had a strong influence on yield strength the effect of grain size was negligible. The different strength levels could be explained by regarding the arrangement of dislocations and vanadium carbide particles, and their mutual interaction. Specimens tranformed at $600^{\circ}C$ showed the highest strength levels. In this case precipitation has occured after the $\gamma$- $\alpha$ transformation. Very small VC particles are arranged mostly along dislocation lines. Increasing both, grain size and pearlite volume fraction leads to a remarkable shift of transition temperature which was further enhanced by increasing ferrite strength.

• IEIE Transactions on Smart Processing and Computing
• /
• v.2 no.4
• /
• pp.216-225
• /
• 2013

This paper discusses the issues regarding an abnormal V-shaped error confronting algebraic-based deconvolution process. Deconvolution was applied to an analysis of the effects of the Random Telegraph Noise (RTN) and Random Dopant Fluctuation (RDF) on the overall SRAM margin variations. This paper proposes a technique to suppress the problematic phenomena in the algebraic-based RDF/RTN deconvolution process. The proposed technique can reduce its relative errors by $10^{10}$ to $10^{16}$ fold, which is a sufficient reduction for avoiding the abnormal ringing errors in the RTN deconvolution process. The proposed algebraic-based analyses allowed the following: (1) detection of the truncating point of the TD-MV distributions by the screening test, and (2) predicting the MV-shift-amount by the assisted circuit schemes needed to avoid the out of specs after shipment.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.15-19
• /
• 2003

In this paper, the bit error rate (BER) performance of the fast frequency hopping/M-ary frequency shift keying system using the clipper receiver is analyzed by using the characteristic function (CF) technique in the presence of n=1 band multitone jamming and additive white Gaussian noise environment. The CFs of the clipper receiver outputs are derived as a infinite series representation using Gamma function and Marcum's Q -function. The analytical results are validated with various simulation results. Performance comparisons with linear combining receiver are shown that the BER performance of the clipper receiver is much better than that of the linear combining receiver In addition, as the clipping level approaches to infinity, it is shown that the clipper receiver simply performs a linear combining without clipping and there exists an optimum value of diversity level (the number of hops per symbol) that maximizes the worst case BER performance of the clipper receiver.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.6
• /
• pp.934-936
• /
• 2004

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.128-132
• /
• 2010

Photonic crystal is dielectric materials or a set of different dielectric materials with periodic structure. Line defect is obtained by leaving out a row of rods along the $\Gamma$-X direction. We showed the change of group velocity in waveguide mode and found resultant small group velocity. Characteristics of the small group velocity were described by electric field distribution. Investigating the phase shift, it is confirmed if small group velocity is positive or negative.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.870-874
• /
• 2004

This work presents a study on development of a practical and quantitative technique for assessment of the structural health condition by Piezoelectric impedance-based technique associated with longitudinal wave propagation method. The bolt fastening condition is adjusted by torque wrench. In order to estimate the damage condition numerically, three damage indices, impedance peak frequency shift ${\Delta}F$, peak amplitude ratio $\delta$ and quality factor ratio $\gamma$, are proposed in this paper. Furthermore, an assessment method is described for estimation of the damage by using these three damage indices.