• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.50-55
• /
• 2010

In recent years, the development of fuel cell vehicles has further accelerated because of environmental problem and petroleum resources shortage. The fuel cell vehicles have the stack which converts fuel to electricity. The stack is usually mounted by bush to isolate the vibration of chassis and body. This paper analyzed the vibratory characteristics of stack and chassis, body system. The wheel forces of fuel cell vehicle are measured to estimate the road load data. And the paths of vibration from wheel to stack are analyzed by CAE. According to the test and CAE results, the improvement of stack vibration are evaluated.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2834-2838
• /
• 2008

An free breathing proton exchange membrane fuel cell (PEMFC) was developed. This paper presents a study of the several effect on the performance of a fuel cell such as air flow rate, opening ratio, and cathode structures. Especially, an air flow rate is critical condition to improve the fuel cell performance. In this paper, we developed a synthetic jet micro air blower to supply high stoichiometric air. The synthetic jet actuation is usually generated by a traditional PZT-driven actuator, which consists of a small cylindrical cavity, orifices and PZT diaphragms. In comparison with free convection fuel cells, the forced-convection fuel cell which equipped synthetic jet micro air blower brings higher performance and stability for long term test. Also, power consumption of the synthetic jet micro air blower is under 0.3W. The results show that the maximum power density was $188mW/cm^2$ at $400mA/cm^2$. The maximum power density was higher 40% than power density of free convection fuel cell.

• 상하수도학회지
• /
• 제21권4호
• /
• pp.439-444
• /
• 2007

Using the anaerobic digester gas as a fuel, fuel cells have the potential to provide significant environmental and economic benefits. A molten carbonate fuel cell power plant was installed in the municipal sewage works of Tancheon in Seoul. The fuel cell unit operates on anaerobic digester gas and provides power and heat for the sewage works. This is the first project of its kind in Korea. This article outlines the experiences of gas purification process with planning, installation and operation. The engineering and installation phase is described regarding to the special features of digester gas, for example impurities in gas composition. Such impurities would be harmful to fuel cells. Operational results from the field test with a gas purification process plant are presented in this paper.

• 한국산학기술학회논문지
• /
• 제15권5호
• /
• pp.2553-2558
• /
• 2014

회전익 항공기 중 군에서 운용하는 기동헬기는 전장상황에서 운용되기 때문에 연료셀 피탄 시 발생 가능한 상황을 예측하여 설계에 반영해야 한다. 연료셀 설계 고려사항은 피탄 상황의 연료셀 내부 압력, 충격파에 의한 연료셀 자체 및 금속 피팅부 응력, 탄의 운동에너지 등이 포함될 수 있다. 중요 설계데이타 확보를 위해서는 실물 연료셀을 이용한 입증시험을 수행하는 것이 가장 좋은 방법이다. 그러나, 극한조건하의 입증시험은 상당한 비용과 시간이 요구되며, 실패 위험성도 높다. 따라서, 실물을 이용한 시험을 수행하기 전 시행착오의 가능성을 줄이기 위해서는 다양한 수치해석을 통해 연료셀 내부압력과 응력 등의 설계 데이타 예측이 반드시 필요하다. 본 연구에서는 입자법을 사용하여 연료셀의 중요 입증시험 중 하나인 피탄시험에 대한 수치해석을 수행하였다. 수치해석은 전용 충돌해석 프로그램인 LS-DYNA를 사용하였고, 피탄의 영향으로 연료셀 내부 압력은 350~360MPa, 수압램에 의한 굽힘하중으로 260~350MPa의 등가응력이 금속피팅부에 발생하는 것으로 파악되었다.

• Journal of Power Electronics
• /
• 제11권1호
• /
• pp.82-89
• /
• 2011

Differences in the frequency characteristic applied to a ripple current may shorten fuel cell life span and worsen the fuel efficiency. Therefore, this paper presents an experimental analysis of the ripple current applied variable frequency characteristic in a polymer electrolyte membrane fuel cell (PEMFC). This paper provides the first attempt to examine the impact of ripple current through immediate measurements on a single cell test. After cycling for hours at three frequencies, each polarization and impedance curve is obtained and compared with those of a fuel cell. Through experimental results, it can be absolutely concluded that low frequency ripple current leads to long-term degradation of a fuel cell. Three different PEMFC failures such as membrane dehydration, flooding and carbon monoxide (CO) poisoning that lead to an increase in the impedance magnitude at low frequencies are simply introduced.

• 드라이브 ㆍ 컨트롤
• /
• 제16권2호
• /
• pp.80-90
• /
• 2019

Fuel cell hybrid electric vehicle is an attractive solution to reduce pollutants, such as noise and carbon dioxide emission. This study presents an approach for energy management and control algorithm based on energetic macroscopic representation for a fuel cell hybrid electric vehicle that is powered by proton exchange membrane fuel cell, battery and supercapacitor. First, the detailed model of the fuel cell hybrid electric vehicle, including fuel cell, battery, supercapacitor, DC-DC converters and powertrain system, are built on the energetic macroscopic representation. Next, the power management strategy was applied to manage the energy among the three power sources. Moreover, the control scheme that was based on back-stepping sliding mode control and inversed-model control techniques were deduced. Simulation tests that used a worldwide harmonized light vehicle test procedure standard driving cycle showed the effectiveness of the proposed control method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.49-52
• /
• 2008

The present study conducts a series of experiments to develop a novel air supplying module for a micro fuel cell using piezoelectric linear actuator. An intermittently and operating air breathing module with reciprocating motion of the linear actuator has been suggested in the present study. A test bench for a micro fuel cell system has been constructed to estimate performance of the active fuel cell system using the air supplying module. With the stroke and operating duty as main control parameters, the optimal operating method of the air supplying module has been discussed.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.185-192
• /
• 2011

This study deals with a basic proposal to prove the safety for the exhausted fittings of the hydrogen fuel cell vehicle. First, this study was approached to numerical analysis solving to close the exact boundary condition (Axial, Bending, Lateral) and the second, this study produced the Lateral movement equipment for the vibration. For the numerical analysis, This study was considered with the exact solution of Lateral movement and the resonance effect for durability sample according to fitting positions. The second, This study was made for special equipment for displacement/gas leak and the frequency because the domestic samples were comparing with foreign fitting and foreign fitting for the hydrogen fuel cell vehicle. The result of this study was satisfied with domestic fittings for the basic reference but it need more test because of other situation for hydrogen fuel cell vehicle.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.29-32
• /
• 2008

Testing was conducted to determine the performance of a residential fuel cell system when subjected to DSS and WSS operation, especially for start-up and shut-down characteristics. In terms of start-up time, it took about 70min to start output power generation and stably to reach 1kW at cold start. Measurement of the characteristics of heat and power generation were carried out at start-up and shut-down time. Fuel gas is used for heating both reformer and stack from start-up to the beginning of power generation. In terms of start-up and shut-down characteristics, it was important to control the reformer temperature precisely. The average output water temperature during the rated output operation(960W) was $63.2^{\circ}C$ constantly. The results of the investigation are being used to develop a new test protocols for residential fuel cell system.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.165-168
• /
• 2007

The objective of this study is to demonstrate and commercialized for on-board fuel storage system for the hydrogen fuel cell vehicles. Type3 composite cylinder is consisting of the full wrapped composites on a seamless aluminum liner. Especially, the seamless aluminum liner has been commercialized with development of fabrication through this study. The key technologies, including design, analysis and the optimized filament winding process for 350bar composite cylinder, were established and verified with design qualification test in accordance with international standard. And the facilities for fabrication and design qualification test have been constructed.