• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.631-636
• /
• 2001

The internal flow in the rocket pump inducer of LE-7 engine for H-II rocket was predicted at design and off-design flow rates using CFD code, CFX- Tascflow. In this numerical study, the performance curve of inducer coressponding to flow rates variation and the internal flow in the front of blade leading edge show good agreement between the calculations and the measurements. Backflow is appeared at suction side of leadinge edge tip, and this region is extended to upstream as flowrate decrease. Because of backflow, pressure loss coressponding to meridinal coordinate occupy 50% from inlet domain to leading edge. By this phenomena, pressure loss in front of blade leading edge take a great effect to inducer performance.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1199-1213
• /
• 2011

이수가압식 쉴드공법은 사질토에서 적용성이 우수하지만, 이수압이 낮으면 이수 유출 및 지반변형이 발생하기도 한다. 따라서 이수가압식 쉴드에서는 초기 막장압보다 큰 초과 이수압을 가하여 막장 안정을 유지한다. 그러나 이수압이 너무 높으면 전방 지반의 수동 파괴를 유발하므로 수동 파괴 위험성을 줄이고 이수압을 증가시키는 방법으로 막장 전방에 수평 차수층을 설치하는 방안이 있으나 위치와 규모, 효과가 잘 알려져 있지 않다. 따라서 본 연구에서는 포화 사질토에서 막장전방에 차수 그라우팅 적용시 발생하는 효과를 규명하기 위하여 모형실험을 수행하였다. 실험 결과, 차수층이 있는 경우가 없는 경우보다 이수압을 크게 가할 수 있어서 전방 차수층이 막장 안정성을 증대시킬 수 있다는 것을 확인하였다. 막장 안정성 증대에 가장 큰 영향을 주는 적정 차수층은 길이 1.0~1.5D, 설치높이 1.0D로 나타났다. 초기 막장압 대비 최대 이수압의 비로 막장의 자립 안전율(F)을 제안할 수 있으며, 전방 차수층을 적정 위치에 설치할 경우 초기 막장압보다 3.5~4.0배 크게 이수압을 가할 수 있는 것으로 나타났다.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.248-255
• /
• 2013

The objective of this study is to optimize the Metal Injection Molding(MIM) process with design of experiments(DOE) and numerical analysis. To derive the optimal process condition, experiment or numerical analysis was performed under various process conditions. To analyze the interaction among influential factors contributing to the temperature at flow front and response surface in MIM, both central point and axial point were added to the full factorial design with 2 levels and 5 factors and then their impacts on response variable in 43 experimental conditions were analyzed and the significance was evaluated. As a result, sprue, runner, and gate were completely filled in about 0.247 seconds after injection, the front part of the green body was filled in about 0.3344 seconds, the green body except gate, etc changed to almost solid state in about 3.29 seconds, the Packinging pressure was completed in about 6.29 seconds, and the green body inside and outside and sprue, etc became solid in 13.2 seconds. The impact of individual or reciprocal action of factors on the temperature at flow front was analyzed through regular probability, test statistics, main effect, and interaction effect. As a result, of a total of 31 combinations of factors, 9 unit factors and reciprocal actions were significant, and the screening was also possible. A proper regression equation was drawn with regression analysis and response surface design on the response variable of temperature at flow front, and the applicability could be verified.

• 한국산학기술학회논문지
• /
• 제15권6호
• /
• pp.3950-3960
• /
• 2014

본 연구에서는 수치모의를 통해서 월류 흐름이 존재하는 수몰 사각 실린더의 항력 특성에 대하여 분석하였다. 모의의 신뢰성을 검토하기 위하여 실험자료와 비교하였으며 실험에서 측정하기 어려운 실린더 접촉면의 압력에 대한 분석을 통해서 상대 수심에 따른 항력의 특성을 분석하였다. 3차원 동수역학 모형을 이용한 수몰 사각 실린더의 항력 계산 결과는 실험자료의 상대 수심의 변화에 따른 항력계수의 변화를 유사하게 모의하고 있음을 확인할 수 있었다. 수치모의 결과 분석에 의하면 수몰 사각 실린더에 작용하는 항력은 대부분 압력이며 상대 수심이 증가함에 따라 전단력의 비중은 감소하였다. 실린더 접촉면의 압력계수 분석 결과에 의하면 상대 수심이 낮은 경우에는 전면부에 높은 압력계수가 형성되고 후면부에 낮은 압력계수가 형성되어 결과적으로 높은 항력계수가 나타남을 확인하였다. 상대수심이 증가하면 전면부의 압력계수는 감소하고 후면부의 압력계수는 증가하여 2차원 흐름 내의 사각 실린더와 유사한 양상을 나타낸다. 정수압 영향 분석에 의하면 전면부와 후면부의 수위 차에 의한 정수압은 항력에 미치는 영향이 제한적이며 사각 실린더에 의해 형성되는 국부적인 수위와 함께 3차원적인 흐름에 의해 형성되는 동수압의 영향이 크다는 것을 확인하였다.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.178-186
• /
• 2002

3-D numerical studies are performed to investigate the effect of the trunk height and approaching air velocities on the pressure distribution of notchback road vehicle. For this purpose, the models of test vehicle with four different trunk heights are introduced and PHOENICS, a commercial CFD code, is used to simulate the flow phenomena and to estimate the values of pressure coefficients along the surface of vehicle. The standard k-$\xi$ model is adopted for the simulation of turbulence. The numerical results say that the height variation of trunk makes almost no influence on the distribution of the value of pressure coefficient along upper surface but makes very strong effects on the rear surface. That is, the value of pressure coefficient becomes smaller as the height is increased along the rear surface and the bottom surface. Approaching air velocity make no differences on pressure coefficients. Through the analysis of pressure coefficient on the vehicle surfaces one tried to assess aerodynamic drag and lift of vehicle. The pressure distribution on the rear surface affected more on drag and lift than pressure distribution on the front surface of the vehicle does. The increase of trunk height makes positive effects on the lift decrease but negative effects on drag reduction.

• 한국생활과학회지
• /
• 제21권3호
• /
• pp.567-576
• /
• 2012

The purpose of this study was to analyze and determine the relationship between physiological responses including blood flow rate and garment pressure, and the feeling of restrictive tightness associated with the wearing skinny pants as a popular clothing style. Evaluation was based on material type, posture and activity type, and body part location. Five female college students took part in this research. Five kinds of experimental clothes with waist measurements of 66cm were chosen. An analysis of the selected skinny pants demonstrated the degree of the whole looseness was higher in this order: clothing type A>B>D>C, and E with E being knitted cloth. Garment pressure was the highest in the front knee portions and was lowest in the outside thigh region. Garment pressure was highest in this sequence : clothing type C>=D>A>=B>E. In terms of posture and activity types, garment pressure was the highest when research participants were crouching, and was the lowest when standing. The blood flow rate was highest in this order: clothing type E>D>B>A>C. Type C skinny pants impeded blood flow and demonstrated the tightest and most restrictive relationship. Blood flow rate varied depending on the type of movement and was highest in this order: getting up, rowing, kicking, jumping and O-shaped leg posture. The results of subjective pressure evaluation demonstrated that pressure was highest in this order: E>=C>B>A>D. These results suggests the need to improve on the patterns and the material design in the area of the front knees. The degree of the looseness when wearing skinny pants did not always correspond to garment pressure or subjective sensation.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.333-334
• /
• 2002

Injection-compression molding parts are many cases with complicated boundary condition which is difficult to analysis of mold characteristics precisely. In this study, the effects of various process parameters such as multi-point gate location, initial charge volume, injection time and pressure have been investigated using finite element method to fomulate the melt front advancement during the mold filling process. A general governing equation for tracking the filling process during injection-compression molding is applied to volume of fluid method. To verify the results of present analysis, they are compared with those of the other paper. The results show a strong effect of processing conditions as a result of variations in the three-dimensional complex geometry model.

• 대한기계학회논문집A
• /
• 제31권4호
• /
• pp.417-424
• /
• 2007

This paper reports fabrication and characterization of a pressure sensor using a pitch-based carbon fiber. Pitch-based carbon fibers have been shown to exhibit the piezoresistive effect, in which the electric resistance of the carbon fiber changes under mechanical deformation. The main structure of pressure sensors was built by performing backside etching on a SOI wafer and creating a suspended square membrane on the front side. An AC electric field which causes dielectrophoresis was used for the alignment and deposition of a carbon fiber across the microscale gap between two electrodes on the membrane. The fabricated pressure sensors were tested by applying static pressure to the membrane and measuring the resistance change of the carbon fiber. The resistance change of carbon fibers clearly shows linear response to the applied pressure and the calculated sensitivities of pressure sensors are $0.25{\sim}0.35 and 61.8 ${\Omega}/k{\Omega}{\cdot}bar$ for thicker and thinner membrane, respectively. All these observations demonstrated the possibilities of carbon fiber-based pressure sensors.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.187-194
• /
• 1999

In the design of catalytic converter, velocity distribution is more important than pressure drop because monolith pressure drop is about 80% of overall pressure drop. For the catalytic converter with single diffuser, pressure drop is decreased as the angle of diffuser decrease, but when the angle is below 18$^{\circ}$, the effect is almost negligible . For the catalytic converter with double diffuser, variation of the angle of the first diffuser shows the same trend as the pressure drop while the shape of diffuser gives little influence on that The outlet shape gives negligible effect on the pressure drop and velocity . distribution . Results show that recirculation region of commercial model is aoubt 30% of the total area in the front of monolith. For the catalytic converter with Model 11 that was presented in the study, recirculation region was not detected more uniform velocity distribution was obtained, and pressure drop was also decreased.

• 대한기계학회논문집B
• /
• 제21권11호
• /
• pp.1403-1412
• /
• 1997

When a high-speed railway train enters a tunnel, a compression wave is generated ahead of the train and propagates through the tunnel, compressing and accelerating the rest air in front of the wave. At the exit of the tunnel, an impulsive wave is emitted outward toward the surrounding, which causes a positive impulsive noise like a kind of sonic boom produced by a supersonic aircraft. With the advent of high-speed train, such an impulsive noise can be large enough to cause the noise problem, unless some attempts are made to alleviate its pressure levels. In the purpose of the impulsive noise reduction, the present study calculated the effect of porous walls on the compression wave propagating into a model tunnel. Two-dimensional unsteady compressible equations were differenced by using a Piecewise Linear Method. Calculation results show that the cavity/porous wall system is very effective for a compression wave with a large nonlinear effect. The porosity of 30% is most effective for the reduction of the maximum pressure gradient of the compression wave front. The present calculation results are in a good agreement with experimental ones obtained previously.