• Transactions of Materials Processing
• /
• v.27 no.3
• /
• pp.160-164
• /
• 2018

The success of warm forming of Mg alloy sheets is very dependent on its frictional behavior at elevated temperatures. The effects of contact pressure and sliding length on the frictional characteristics of AZ31B Mg alloy sheet were investigated at elevated temperature and at room temperature. The contact pressure range for the friction test was determined through FE analysis of the roof panel which is a candidate for Mg alloy application. According to the experimental results, the frictional behavior of the Mg alloy sheet is equally highly influenced by both sliding length and contact pressure at room temperature. At elevated temperatures, however, the sliding length has a more dominant influence on the frictional characteristics of the Mg alloy sheet than the contact pressure, if the contact pressure is lower than a certain level.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.10-20
• /
• 1998

In this paper, the effects of material properties on the friction and wear behavior of pure metals are investigated. The sliding material pairs are selected based on their relative compatibility and relative hardness ratio of the specimen. The initial and steady-state friction coefficients are obtained in the experiments and the wear rates are quantitatively investigated. It is shown that the initial friction coefficient is affected by the hardness ratio of sliding materials. Furthermore, in steady state condition, neither hardness ratio nor compatibility has significant influence on the frictional behavior. As for wear, the ductility of the metal affects the wear particle generation process which in turn affects the frictional behavior. The findings of this research suggest that frictional interaction cannot be simply characterized by either compatibility or hardness ratio of the materials undergoing sliding contact.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.241-247
• /
• 2017

Railway bridges with continuously welded rail have a limitation of span length due to track-bridge interaction. In order to overcome this, a sliding slab track system has been developed that comprises with a low-frictional sliding layer between the bridge deck and the track slab to isolate the longitudinal behavior between the bridge and the track. In this study, a real scale track system is prepared to experimentally evaluate the longitudinal frictional behavior. Applied loading rates were 0.2, 1.0, 5.0 and 10mm/min; vertical mass on the track are track slab only, 5,000 and 10,000kg added mass, respectively. Test results showed that the resulting frictional coefficients varied from 0.22 to 0.33. In addition, 10,000 cycle loadings were applied to simulate repetitive sliding to represent 30 years of service life. The frictional coefficient increase was measured and found to be 7% of that of the initial loading stage, which means that the sliding layer is adequate to provide low-frictional behavior for the sliding slab track system. Effects of changes of the frictional coefficient of the sliding layer were analyzed by rail-structure interaction analysis.

• Tribology and Lubricants
• /
• v.11 no.3
• /
• pp.11-23
• /
• 1995

The friction and wear behavior of $Al_{2}O_{3}$, SiC, and $Si_{3}N_{4}$ under the different sliding conditions were investigated. The cylinder-on-disc wear tester was used for a wear test method. Using the servo-motor, the sliding speed did not alternate due to the frictional forces. Three kinds of loads were selected to watch the variation of the wear rates and the frictional forces under a constant speed. Three kinds of sliding conditions were used to see the effects of the oxidation and the abrasion. The dominant wear mechanisms of $Al_{2}O_{3}$ were the abrasion and the formation of transfer layers. The abrasion has a great effect on the wear of SiC. The wear of $Si_{3}N_{4}$ was due to the asperity-failure and the oxidation. Also, the wear rate of each ceramic is shown to be related to the frictional power provided to the tribological system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.152-155
• /
• 2004

Effects of sliding speed, applied load, counterpart radius and thickness of PMMA (Poly Methyl Methacrylate) coating layers on their dry sliding frictional and wear behavior were investigated. Sliding wear tests were carried out using a pin-on-disk wear tester. The PMMA layer was coated on Si wafer by a sol-gel technique with two different thicknesses, $1.5{\mu}m\;and\;0.8{\mu}m$. AISI 52100 bearing steel balls were used as a counterpart of the PMMA coating during the wear. Normal applied load and sliding speed were varied. Wear mechanisms were investigated by examining worn surfaces by an SEM. Under most of sliding test conditions, the thicker layer with the thickness of $1.5{\mu}m$ showed lower fiction coefficient than the thinner layer. Effects of sliding speed and counterpart's radius on the frictional behavior were varied depending on the thickness of the coating layer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1361-1364
• /
• 2004

There is a need for fundamental understanding of biotribological characteristics of various biomaterials sliding against biological materials in order to develop a moving mechanism of medical microsystems having high energy efficiency. A special experimental equipment was designed and built to study the frictional behavior of various biomaterials sliding against a small intestine specimen of a pig. Friction experiments for six biomaterials were performed. Particularly, the effects of load and speed on frictional behavior were investigated. The results of this work will aid in the development of the actuator for a self-propelling micro-endoscope.

• Journal of the Korean Society of Safety
• /
• v.35 no.1
• /
• pp.53-61
• /
• 2020

This study proposes a new damper configuration for seismic performance improvement of heavy sliding facilities inside a building. For this purpose, we deal with two connection types of control system, and the parametric study has been performed to investigate their comparative seismic performances according to the variations of the control capacity. In order to simulate the seismic responses of the proposed system, we employed a recently-developed seismic response analysis method that can deal with the two-mass system with nonlinear frictional sliding behavior. The numerical results demonstrate that the typical method of diagonal bracing damper connection can exhibit effective control performance both on structure and the heavy sliding facilities, whereas the structure-facilities connection method does not show any control effect on both responses. On the other hand, the typical method has some limitations that it can adversely cause excessive sliding of the facilities, depending upon the frequency characteristics of structure and earthquake. On the contrary, the structure-facilities connection method is very effective in reducing the sliding displacement of the heavy facilities, even with small amount of control capacity. Thus, the following potential expectations can be inferred from these results: The typical diagonal bracing damper connection method will have some promising benefits in controlling the sliding facilities inside the building as well as the building itself, and the structure-facilities connection method can be a cost-effective way of protecting the internal heavy important facilities inside the structure already designed with sufficient seismic performance.

• Transactions of Materials Processing
• /
• v.13 no.8
• /
• pp.716-722
• /
• 2004

Effects of sliding speed, applied load, and thickness of PMMA (Poly Methyl Methacrylate) coating layers on their dry sliding frictional and wear behavior were investigated. Sliding wear tests were carried out using a pin-on-disk wear tester. The PMMA layer was coated on Si wafer by a spin coating process with two different thicknesses, $1.5\mu\textrm{m}$ and $0.8\mu\textrm{m}$. AISI 52100 bearing steel balls were used as a counterpart of the PMMA coating during the wear. Normal applied load and sliding speed were varied. Wear mechanisms of the coatings were investigated by examining worn surfaces using an SEM. Friction coefficient of the coatings decreased with the increase of the applied load. Both adhesion and deformation of the coating determined the coefficient. The thicker PMMA layer with the thickness of $1.5mutextrm{m}$ showed lower friction coefficient than the thinner layer under most test conditions. Effects of sliding speed and applied load on the frictional behavior were varied depending on the thickness of the coating layer.

• Transactions of Materials Processing
• /
• v.17 no.6
• /
• pp.401-406
• /
• 2008

The frictional behavior of stamping process is a function of interface parameters such as sheet and tool material, lubricant, surface roughness, contact pressure, sliding speed etc. Among these parameters the thing that can be controlled by a steel maker is the surface roughness of sheet. In this study, effects of surface roughness on the frictional behavior of steel sheet for automotive were investigated to find out the way to improve the frictional characteristics of steel sheet. The cold rolled steel sheets with various surface roughnesses were prepared for the test. The flat type friction test was conducted with different lubricant conditions. The surface roughness effect on frictional behavior depends on the viscosity of lubricant. The frictional characteristic of steel sheet was influenced by the amplitude of roughness as well as the shape of that.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.6
• /
• pp.1753-1761
• /
• 1996

The wear behaviors of ${Si_3}{N_4}$ under the different sliding conditions were investigated. The cylinder-on-disc wear tester was used. Using the servo-metor, the sliding speed did ot alternate due to the frictional forces. Threekinds of loads and speeds were selected to watch the variation of the wear rates and the frictional forces. Also three kinds of sliding condition under a constant speed were used to see the effects of the oxidationand the abrasion. The contact pressure was more effective than the repeated cycle on the wear behavior of ${Si_3}{N_4}$. With the low loads, the effect of the asperity-failure was more dominant than that of oxidation and abrasion. As increasing the load, the effects of oxidation and abrasion were increased, but the asperity-failure effects were decreased. The wear particles destroyed the ozide layers formed on sliding surfaces. The wear rate could be decreased due to delaying the oxidation. The frictional power and the wear weight per time were usefuel to see the transition of wear.