• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.46-50
• /
• 1991

The Frictional behavior in single crystal (111) p-type silicon as influenced by electolytic solutions have been studied. Linear scratching by diamond indentor was carried out to show the variation of friction between silicon and diamond indentor immersed in electrolytic solutions. The results indicate that concentration of the solutions influence the fricational coefficient. In addition there is a correlation between measured zeta-potential and frictional coefficients. The zeta-potential in various concentrations was measured to estimate the variation of the Peierls energy. The proposed model predicts a minimum frictional coefficient near a concentration of $10^{-3}$ M/l NaOH in deionized water and explains the chemomechanical effect observed in this study.

• 소성∙가공
• /
• 제19권4호
• /
• pp.236-241
• /
• 2010

The frictional behavior of bare steel sheet highly depends on surface roughness. It was investigated that the change of surface roughness of bare steel sheet due to deformation for each forming mode. The flat type friction test was done to check the effect of surface roughness change on frictional characteristics of bare steel sheet. As increasing the deformation, the Ra value was increased at stretching forming mode and drawing forming mode, however the change of Pc showed different trends. The Pc was decreased as increasing stretch deformation but increased at compression deformation. At drawing forming mode, the friction coefficient was increased as deformation was increased after initial big drop with drawing oil. As deformation was increased, the friction coefficient was decreased with drawing oil at stretching forming mode. The results show that the deformation changes the surface roughness and frictional characteristics of steel sheet but the effect depends on the forming mode.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.249-253
• /
• 1994

In machine tools, frictional force exists between the table and the bed, and in ballscrews. In this paper, feed motor current is used to measure the motor torque and frictional force. A hall sensor is used to measure the feed motor current. Some frictional pheonomina in feed drice systems, such as, the relationship between feedrate and frictional force, lubrication conditions and frictional force, and feed direction and frictional force, are obtained. Generally, the friction behavior is in good agreement with Stribeck's curve. However, the data shows significant scatter when feedrate is high.

• 한국지반공학회지:지반
• /
• 제5권3호
• /
• pp.51-62
• /
• 1989

보강토옹벽의 원심모형분험의 예비실험으로서 모래와 보강재 사이의 마찰거동의 특성을 조사.연 구하기 위하려 마찰실험을 행하였다. 보강재의 종류 및 길이를 변화시킴으로써 그들이 모래와 보강재 사이의 마찰계수에 미치는 영향을 조사하였다. 한편 다른 두가지 실험방법(직원전단시험과 인발시험)을 택하여 어떤 방법이 실제 현장에서의 보강재의 거동을 잘 나타내는지를 비교.검토하였다.

• Korea-Australia Rheology Journal
• /
• 제13권2호
• /
• pp.89-95
• /
• 2001

Effects of particulate size and frictional characteristics were examined on the melting behavior of PP(polypropylene) in a twin screw extruder. Powder and pellet types of PP were used and each component was blended with PE(polyethylene) wax and clay, respectively. It was observed that small size particulates, 1.e. powder systems exhibit accelerated melting behavior; and it was also found that the abrasive auditive acts as an effective agent for fast melting of PP powder. Retardation of melting due to the reduced friction was observed in both types of PP, contrary to the result found in a batch mixer. The tendency observed in variation of torque and exit temperature was explained in terms of frictional effect and length of compacted region formed during evolution of melting.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.125-133
• /
• 2011

The wear of rubber track being in contact with the road surface is an important subject because it decreases the traction performance and the operating efficiency of tracked vehicle. For the above reasons, many attempts have been made to quantitatively calculate the rubber track. However, it depends on the experimental methods which are highly time- and cost-consuming. Therefore, the numerical simulation approach is highly desirable, but it needs to model the complex geometry and the material behavior in details as well as the interaction with the road surface. In this study, the rubber track and its material behavior are elaborately modeled since these factors are very important in the prediction of the wear rate of the rubber track. Accordingly to the studies on the rubber wear by previous investigations, it has been found that the wear is greatly influenced by the frictional energy. The frictional energy of rubber track is computed by utilizing the 3D finite element analysis of the rubber track, and the wear rate is evaluated making use of the frictional energy and a wear model.

• KSTLE International Journal
• /
• 제7권2호
• /
• pp.51-55
• /
• 2006

In order to design an effective foot surface which can provide adequate friction for a self-propelled medical microrobot moving inside the small intestine, frictional mechanisms between the small intestine inner wall and the foot surface of the robot must be understood. In this paper, mechanical interlocking effect was considered to design the surface of the foot that can generate the desired frictional force. The concept of the design was derived from the hookworm that lives inside the small intestine. Hookwarms are known to adhere to the small intestine wall by interlocking with villi on the surface of the small intestine. The interlocking mechanism was considered as the main frictional mechanism for the design of the microrobot foot surface in this work. 2 mm and 6 mm diameter solid and hollow cylindrical shaped foot specimens were designed and tested to assess the frictional force between the specimens and the porcine small intestine specimen.

• 한국지반공학회논문집
• /
• 제36권11호
• /
• pp.107-117
• /
• 2020

개단 강관말뚝의 경우 일반적으로 말뚝에 작용하는 외부 주면 마찰력뿐만 아니라 설치과정에서 폐색된 흙이 강관 내부에 작용하는 내부 마찰저항이 존재한다. 내·외부 저항에 따라 극한하중의 변화가 예상되며, 말뚝이 시공된 지반이 점성토일 경우 지반 침하로 유발되는 부주면 마찰력에도 영향을 끼칠 것으로 판단된다. 따라서 본 연구에서는 강관말뚝 내·외부 저항 특성에 따른 거동을 수치해석적으로 분석하고자 하며, 지반 침하 발생 전·후의 마찰력 분포, 축력, 침하량을 산정하였다. 해석 결과, 내부 마찰 저항은 외부 마찰 저항보다 적은 영향을 미쳤지만 전체적인 말뚝 거동에 끼치는 영향을 고려하였을 때, 중요한 요소 중 하나이며 설계 시 두 가지 저항요소를 고려할 필요가 있을 것으로 판단된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1361-1364
• /
• 2004

There is a need for fundamental understanding of biotribological characteristics of various biomaterials sliding against biological materials in order to develop a moving mechanism of medical microsystems having high energy efficiency. A special experimental equipment was designed and built to study the frictional behavior of various biomaterials sliding against a small intestine specimen of a pig. Friction experiments for six biomaterials were performed. Particularly, the effects of load and speed on frictional behavior were investigated. The results of this work will aid in the development of the actuator for a self-propelling micro-endoscope.

• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.253-258
• /
• 2000

Frictional behavior of wire electric discharge machined surfaces of spheroidized annealed STDll steel was investigated. The surfaces were produced with a various series of finish cuts where pulse energy was reduced with increase in the number of finish cuts. Roughness and micro-hardness of the surfaces were also measured. It is observed that the increase in the number of finish cuts produces the surface exhibiting lower frictional resistance followed by higher resistance after considerable wear. Effects of finish cuts on the friction characteristics are discussed with the aid of roughness and micro-hardness of the surfaces.