• Journal of Welding and Joining
• /
• 제32권5호
• /
• pp.50-57
• /
• 2014

Friction Stir Welding (FSW) is a complex process with several mutually interdependent parameters. A slight difference from known settings may lead to imperfections in the stirred zone. These inhomogeneities affect on the mechanical properties of the FSWed joints. In order to prevent the failure of the welded joint it is necessary to detect the most critical defects non-destructive. Especially critical defects are wormhole and lack of penetration (LOP), because of the difficulty of detection. Online thermography is used process-accompanying for defect detecting. A thermographic camera with a fixed position relating to the welding tool measures the heating-up and the cool down of the welding process. Lap joints with sound weld seam surfaces are manufactured and monitored. Different methods of evaluation of heat distribution and intensity profiles are introduced. It can be demonstrated, that it is possible to detect wormhole and lack of penetration as well as surface defects by analyzing the welding and the cooling process of friction stir welding by passive online thermography measurement. Effects of these defects on mechanical properties are shown by tensile testing.

• 대한기계학회논문집A
• /
• 제32권12호
• /
• pp.1107-1114
• /
• 2008

This paper is aimed to understand the effect of different galvannealing temperatures on the frictional properties and Fe-Zn intermetallic phases of the galvannealed (GA) coatings on steel sheets. Their galvannealing treatments were conducted at 465, 505, 515 and $540^{\circ}C$ for about 10s in the additional heating furnace of an industrial continuous hot-dip galvanizing line. The mechanical and the frictional properties of the coatings were estimated using nanoindentation, nanoscratch, micro vickers hardness tests and flat friction tests, which were performed at contact pressures of 4, 20 and 80MPa. Also, the correlation between the microstructure and the frictional properties of the GA coatings were investigated by SEM observation for the cross-section of the GA coating after and before flat friction tests. The results showed that the mechanical and the frictional properties of the coatings are strongly dependent on their phase distributions and microstructure. Especially, in low contact pressure of 4MPa the frictional properties of the coatings were dependent on the surface phases and morphology, while in high contact pressure of 80MPa it was influenced by their mechanical properties based on the dominant phase distributions.

• 한국산학기술학회논문지
• /
• 제8권6호
• /
• pp.1337-1342
• /
• 2007

본 연구에서는 동시 냉난방 히트펌프용 열교환기의 성능평가 및 설계해석 기술의 확보를 위해 난방운전 온도조건에서 6종의 루버핀-관 열교환기의 공기측 열전달특성 및 마찰특성을 실험을 통하여 조사하였다. 실험을 위해 공기엔탈피방식의 칼로리미터와 항온수조를 이용하였다. 전열량의 증가는 핀피치보다 열수에 의해 더 크게 나타났고, 핀피치가 작을수록 열전달계수는 더 높았다. 또한 핀피치가 작을수록 열수증가에 의한 열전달계수의 증가폭이 커졌다. 핀피치와 열수변화에 대한 j-계수와 f-계수는 레이놀즈 수가 증가할수록 감소하였고, 레이놀즈 수 400부근의 영역에서 역전현상이 존재하였다.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.315-319
• /
• 2020

In various fields, several studies based on carbon nanotubes (CNTs) have been conducted. The results of previous studies, wherein CNT coatings have been incorporated as solid lubricants, demonstrate that the friction and wear characteristics of CNT coatings can be improved through the absorption/dispersion of the contact pressure by controlling the stiffness of the nanomesh structure comprising CNT strands. In this study, the friction and wear characteristics of the following are compared: CNT coating formed by spin coating of CNT solution, compressed CNT coating, and compressed/heated CNT coating (wherein CNT strands are squeezed through compression and/or heating). It is observed that the friction coefficient of the CNT coating having the largest number of voids between the CNT strands is significantly lower than those of the compressed CNT coating and the compressed/heated CNT coating. The wear tracks of the compressed CNT coating and the compressed/heated CNT coating indicate that some parts become torn or adhere into a lump. However, in the case of the CNT coating, a smooth wear surface is formed by rubbing. Furthermore, as the void space between the squeezed and adhered CNT strands decreases, the resistance to structural deformation increases, thereby resulting in an increased frictional force and a wear pattern that becomes torn or forms a lump. Hence, the results obtained from this study corroborate that the friction and wear characteristics of CNT coatings can be enhanced through the absorption/dispersion of the contact pressure by controlling the stiffness of the nanomesh structure of CNT coatings.

• 수산해양기술연구
• /
• 제14권2호
• /
• pp.79-87
• /
• 1978

기관밸브용접 SCr4-21-4N 및 SUH3-21-4N을 연구선정된 최적마찰압접조건 하에서 마찰압접을 하고 이때 생기는 압접부의 잔류응력 및 경도의 peak 등 압접결함의 제거 및 압접성능개선을 위한 열처리에 관하여 실험연구한 결과 다음과 같은 결론을 얻었다. (1) 배기 valve용강 SCr4-21-4N 및 SUH3-21-4N의 마찰압접을 위한 최적조건으로서 회전수 3,000rpm, 마찰가열압 p 하(1)=8 kg/mm 상(2), upset 압 p 하(2)=20 kg/mm 상(2), 압접가열시간 t 하(1)=3초, upset 시간 2.5초를 선정한 것이 매우 타당함이 실험적으로 입증되었다. (2) 이종재질 SUH3-SUH31, SCr4-SUH31, SCr4-SUH3, SUH3-CRK22, SCr4-21-4N 및 SUH3-21-4N의 마찰압접에 관한 저자의 종래 연구와 본연구 결과는 압접부의 압접 특성이 서로 매우 일치하였다. (3) SCr4-21-4N 및 SUH3-21-4N의 마찰압접부의 잔류응력 및 전도의 peak를 제거하기 위한 최적열처리조건은 $600^{\circ}C$$\times$30min.$\times$room air cooling의 normalizing임이 확인되었다. (4) 이때 열처리 후에는, 열처리전의 인장강도의 약 20%가 감소했으나, 파단 위치는 열영향부로부터 모재 SCr4 및 SUH3 측으로 이동하였다. (5) 상기 최적조건 하에서 마찰압접되고 열처리된 압접부의 현미경 조직검사 결과, 압접부가 매우 좁고 압접결함이 없으며, 치밀하고 조밀한 조직의 우수한 압접이었음이 확인되었다. (6) 상기 최적조건은, 기관 valve 생산을 위한 타이종재질의 마찰압접조건으로도 응용될 수 있을 것이다.

• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.762-771
• /
• 1987

본 연구에서는 국산 구조용 강인 SM45C와 SUS304재를 마찰가열압력과 업셋압 력을 서로 변화시키고 업셋시간을 2초로 고정하여 압접시간 10초를 기준으로 하여 변 화시키면서 마찰압접한 후 압접시간 변화에 따른 인장강도의 변화와 업셋량 변화에 따 른 인장강도 및 굽힘강도를 고찰하였다.또 최고 강도치를 나타내는 압접조건을 구 한 후 미소 경도치 및 이종재의 압접부에서 미소하게 변화하는 조직변화도 함께 고찰 하였다.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.34-38
• /
• 2008

It was investigated that two rods of aluminium can be welded by hot extru-pressure welding method with stepped welding dies, and that the welding pressure on the welding surface were analyzed by computer simulation according to the stepped shapes of welding dies. It was known by computer simulation that welding pressure on the welding section of rods welded using stepped welding dies. And it was known by experime- nts that two rods of aluminium can be welded on the end sections by hot pressure welding method using stepped welding dies without relative rotational movement of contacted aluminium rods needed for the purpose of friction heating and pressure.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.28-33
• /
• 2001

Screw conveyors are used extensively in industrial for conveying and elevating materials. Despite their apparent simplicity, the mechanics of the conveying action is very complex. so many engineers depend on experiential data. Capacities of screw are pumping, steady flow of polymer melts, steady volumetric throughput etc. they are affected by geometry of screw, heat flux, pressure on inside barrel, rotating velocity, friction coefficient at screw surface etc. by computation volumetric efficiency increases as rotating velocity increases and decreases as friction coefficient increases. also it decreases with short pitch length. and double flight screw is more effective than single flight screw. The temperature of polymer melts by heating pad and injection pressure play a very important role in the injection molding machine. so in this paper we analyze thermal distortion and stress of screw includes pressure and temperature distributions by finite element analysis to understand what design factors influence on volumetric throughput efficiency of the screw and thermo-mechanical characteristics of screw.

• 한국정밀공학회지
• /
• 제30권8호
• /
• pp.847-853
• /
• 2013

Micro-dimples on sliding surfaces have been investigated to reduce the frictional forces on metal bearing surfaces; however, for an elastomer, such as thermoplastic polyurethane (TPU), this has not been studied. The material properties of an elastomer are affected by temperature, and this can shorten the life of the elastomer. In this paper, micro-dimples were applied on the surface of an elastomer in order to reduce the frictional heating, which was experimentally investigated using pin-on-disk apparatus while the surface temperature was measured. To obtain optimal design parameters, the design of the experiment was applied, and the shape of the section, size, depth and density of micro-dimples were selected as the design parameters. The results show that the size of the dimple is the most important design parameter.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.760-765
• /
• 2000

The study deals with the development of a computational procedure for evaluating the temperature rise in dry and lubricated multi-layered contacts of head/disk interface. A transient computational model with a transformed rectangular computational domain is utilized. A model and a computational method for micro-contact with sub-lubricated zone, including friction heat generation, have been presented. The model was applied, taking full account of the changes in contact area and contact load due to frictional heating. The computational distribution of temperature is obtained with the analytical findings for various composition and contact conditions. Especially, a rapid rise ($220^{\circ}C$ or above) in read head temperature lese to a saturation in the influence of a thermal spike on signal performance. This general class of problems can be treated provided that heat generation distribution and layer properties are known.